2009 RENAULT TWINGO RS instrument panel

17B-169V7 MR-413-X44-17B000$150.mif
PETROL INJECTION
Fault finding – Status summary table17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
* RCH: passenger compartment heating resistor
Tool statusDiagnostic tool title
ET075Pedal released and throttle closed
ET076Starting
ET077Impact detected
ET079Air conditioning present
ET081Accelerator pedal position
ET082Motorised throttle position
ET086Camshaft dephaser (Only for Vdiag 4C)
ET088Compressor actuation request
ET089Flywheel target programming
ET093Catalytic converter fault finding
ET094Upstream sensor fault finding
ET095Misfire fault finding
ET111RCH* number set
ET112RCH* cut-off
ET143Low-speed fan assembly relay control
ET144High-speed fan assembly relay control
ET233Clutch pedal
ET289Injection -> instrument panel connection
ET290Petrol pump relay control
ET300Richness regulation
ET340Request by Automatic Transmission for OBD warning light to come on (Only for CLIO III
or MODUS)
ET341Immobiliser code programmed
ET351Injection -> electronic stability program connection
ET357Low-speed fan unit relay connection

17B-184V7 MR-413-X44-17B000$151.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET042CRUISE CONTROL/SPEED LIMITER
STATUS
DEFINITIONNOT DETECTED: This status indicates that the cruise control or speed limiter function
is not present on the vehicle.
INACTIVE: This status indicates that the cruise control/speed limiter main On/Off switch
is in the rest (or neutral) position.
LIMITER: This status indicates that the driver has used the main switch to select the
speed limiter.
CRUISE CONTROL: This status indicates that the driver has used the main switch to
select the cruise control.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system operation
programming.
Use the Wiring Diagram Technical Note for NEW TWINGO, E33, CLIO III
or MODUS.
Conformity check: Engine stopped and ignition on, or engine running at idle speed, and engine coolant
temperature > 80˚C.
NOT DETECTEDThe cruise control or speed limiter function is not present on the vehicle.
"INACTIVE"No button has been pressed.
LIMITERThe speed limiter ON/OFF button has been pressed.
Lights the orange warning light on the instrument panel.
CRUISE
CONTROLThe cruise control ON/OFF button has been pressed.
Lights the green warning light on the instrument panel.
SIM32_V44_ET042/SIM32_V4C_ET042/SIM32_V50_ET042/SIM32_V54_ET042
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

17B-220V7 MR-413-X44-17B000$152.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET289INSTRUMENT PANEL INJECTION CONNECTION
STATUS
DEFINITIONCONNECTED: This status indicates that the connection between the injection
computer and the instrument panel is not defective.
DISCONNECTED: This status indicates that the connection between the injection
computer and the instrument panel is defective.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system operation
programming.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80˚C
NOT CONNECTEDThe connection between the injection computer and the instrument panel is defective,
test the instrument panel (see 83A, Instrument panel) and the multiplex network
(see 88B, Multiplexing).
SIM32_V44_ET289/SIM32_V4C_ET289/SIM32_V50_ET289/SIM32_V54_ET289
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.

17B-223V7 MR-413-X44-17B000$152.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET340AUTOMATIC TRANSMISSION REQUEST TO ACTIVATE OBD

WARNING LIGHT
STATUS
DEFINITIONACTIVE: This status indicates that the automatic transmission computer request to
activate the OBD warning light is active.
INACTIVE: This status indicates that the automatic transmission computer request to
activate the OBD warning light is inactive.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system operation
programming.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80˚C
"ACTIVE"
or
"INACTIVE"For normal engine operation, the status must be INACTIVE.
If activation of the OBD warning light on the instrument panel is not consistent with
the status,
test the instrument panel (see 83A, Instrument panel).
SIM32_V44_ET340/SIM32_V4C_ET340/SIM32_V50_ET340/SIM32_V54_ET340
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.

17B-324V7 MR-413-X44-17B000$172.mif
PETROL INJECTION
Fault finding – Interpretation of parameters17B
SIM 32 injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
* OCS: Oil Control System.
PR873OIL OXIDATION SIGNAL
(except D7F800 and D4F772)
PARAMETER
DEFINITIONThis parameter indicates the distance of the vehicle when the oil dilution threshold is
reached.
NOTESOnly apply the interpretation of this parameter if the OCS* strategy is activated on the
instrument panel. Check the configuration reading LC106 OCS on the instrument panel
computer is WITH.
Conformity check: Engine stopped and ignition on, or engine running, and engine coolant temperature
> 80˚C.
The oil condition is calculated by the oxidation program in the injection computer, according to the number of
engine revolutions.
When this count reaches a certain threshold before the end of the oil service period, the injection computer
sends a signal to the instrument panel, which will display service due. Parameter PR873 corresponds to
the vehicle mileage at the time this signal is sent.
Then the instrument panel computer deducts 900 miles (1500 km) before displaying the message Service required.
IMPORTANT:
When the message Service due appears on the instrument panel, the customer must have the oil changed within
the remaining 900 miles (1500 km).
SIM32_V44_PR873 / SIM32_V4C_PR873 / SIM32_V50_PR873 / SIM32_V54_PR873
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
Repeat the conformity check from the start.

17B-325V7 MR-413-X44-17B000$172.mif
PETROL INJECTION
Fault finding – Interpretation of parameters17B
SIM 32 injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
PR874LAST SERVICE
(except D7F800 and D4F772)
PARAMETER
DEFINITIONThis parameter indicates the vehicle mileage the last time a service was carried out.
NOTESIt is updated when the oil service parameters are reinitialised in the instrument panel.
SIM32_V44_PR874 / SIM32_V4C_PR874 / SIM32_V50_PR874 / SIM32_V54_PR874
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
Repeat the conformity check from the start.