2009 RENAULT TWINGO RS air condition

17B-249V7 MR-413-X44-17B000$152.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET603AIR CONDITIONING COMPRESSOR RELAY CONTROL CIRCUIT
STATUS
DEFINITIONACTIVE: This status indicates that the air conditioning compressor relay control
is active.
INACTIVE: This status indicates that the air conditioning compressor relay control
is inactive.
NOTESThere must be no present or stored faults.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80˚C
"ACTIVE"
or
"INACTIVE"This status becomes ACTIVE when the air conditioning compressor is activated by
the driver.
In the event of a fault, apply the interpretation of DF1072 Air conditioning
compressor control.
SIM32_V44_ET603/SIM32_V4C_ET603/SIM32_V50_ET603/SIM32_V54_ET603
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.

17B-252V7 MR-413-X44-17B000$153.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET673JAMMED ACCELERATOR PEDAL–YES
–NO
STATUS
DEFINITIONYES: This status indicates that the accelerator pedal is detected to be jammed.
NO: This status indicates that the accelerator pedal is not detected to be jammed.
NOTESSpecial notes:
Apply this procedure only if the status is YES.
Use the Wiring Diagrams Technical Note for NEW TWINGO, E33, CLIO III
or MODUS.
Conformity check: Engine stopped and ignition on, or engine running, and engine coolant
temperature > 80˚C
YES
OR
NOThis status varies when the ignition is on or the engine is running depending on the
status of the accelerator pedal.
Check the condition of the connectors of the brake switch (component code 160), of the accelerator potentiometer
(component code 921), and of the engine management computer (component code 120).
If the connector or connectors are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
SIM32_V44_ET673 / SIM32_V4C_ET673 / SIM32_V50_ET673 / SIM32_V54_ET673
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

17B-254V7 MR-413-X44-17B000$153.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET674REFRIGERANT PRESSURE–Too low
–Correct
–Unavailable
STATUS
DEFINITIONTOO LOW: this status indicates that the refrigerant pressure is too low.
CORRECT: this status indicates that the refrigerant pressure is correct.
UNAVAILABLE: this status indicates that the refrigerant pressure is unavailable.
NOTESDeal with DF232 Refrigerant pressure sensor circuit first.
There must be no present or stored faults.
Conformity check: Engine stopped and ignition on, or engine running, and engine coolant
temperature > 80˚C
TOO LOW
or
CORRECT
or
"UNAVAILABLE"The purpose of this status is to check that the circuit is correctly charged with gas.
It becomes active when the air conditioning is detected as being connected and there
are no faults present.
The result of this status is:
–Too low: Pressure below 2 bar.
–Correct: Pressure above 2 bar.
–Unavailable: Cannot perform test.
SIM32_V44_ET674 / SIM32_V4C_ET674 / SIM32_V50_ET674 / SIM32_V54_ET674
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

17B-256V7 MR-413-X44-17B000$153.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET703
CONTINUED 1
"MINUS"
Decrease button pressed.
In the event of a fault, refer to the interpretation of status ET703.
"PLUS"Increase button pressed.
In the event of a fault, refer to the interpretation of status ET703.
Sensor electrical conformity
INACTIVEStatus ET703 becomes INACTIVE when none of the cruise control / speed limiter
buttons is pressed. These buttons are located on the steering wheel.
To carry out the checks and measurements in complete safety, observe the driver's
frontal airbag removal recommendations (see MR 392 (Clio III), MR 385 (Modus),
MR 411 (New Twingo), or MR 442 (E33), Mechanical, 88C, Airbag and
pretensioners, Driver's frontal airbag: Removal - Refitting).
If status ET703 does not display INACTIVE,
–check the condition of the cruise control/speed limiter +/- button and the condition
of its connector.
–check the condition of the cruise control/speed limiter "R/0" button and the
condition of its connector,
If the connector(s) is faulty and if there is a repair procedure (see Technical Note
6015A, Repairing electrical wiring, Wiring: Precautions for repair), repair the
connector, otherwise replace the wiring.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

17B-257V7 MR-413-X44-17B000$153.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET703
CONTINUED 2
INCREASE
Status ET703 becomes INCREASE when the cruise control/speed limiter + button is
pressed. This button is on the steering wheel, on the left-hand side.
To carry out the checks and measurements in complete safety, observe the driver's
frontal airbag removal recommendations (see MR 392 (Clio III), MR 385 (Modus),
MR 411 (New Twingo), or MR 442 (E33), Mechanical, 88C, Airbag and
pretensioners, Driver's frontal airbag: Removal - Refitting).
If status ET703 does not display INCREASE, check the condition of the cruise
control/speed limiter +/- button, and the condition of its connector.
If the connector is faulty and there is a repair method (see Technical Note 6015A,
Repairing electrical wiring, Wiring: Precautions for repair), repair the connector,
otherwise replace the wiring.
Measure the resistance of the following connections while pressing the + button
(on the button connections):
●86G of component 331.
●86M of component 331.
If the resistance is not X ≈ 300 Ω, check the continuity of the connection when the
button is in the rest position.
If there is continuity, replace the +/- control button.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

17B-258V7 MR-413-X44-17B000$153.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET703
CONTINUED 3
DECREASE
Status ET703 becomes MINUS when the cruise control/speed limiter "-" button is
pressed. This button is on the steering wheel, on the left-hand side.
To carry out the checks and measurements in complete safety, observe the driver's
frontal airbag removal recommendations (see MR 392 (Clio III), MR 385 (Modus),
MR 411 (New Twingo), or MR 442 (E33), Mechanical, 88C, Airbag and
pretensioners, Driver's frontal airbag: Removal - Refitting).
If status ET703 does not change to DECREASE, check the condition of the cruise
control/speed limiter +/- button and check the condition of its connector.
If the connector is faulty and there is a repair method (see Technical Note 6015A,
Repairing electrical wiring, Wiring: Precautions for repair), repair the connector,
otherwise replace the wiring.
Measure the resistance of the following connection while pressing the "-" button
(on the button connections):
●86G of component 331.
●86M of component 331.
If the resistance is not X ≈ 100 Ω, check the continuity of the connection when the
button is in the rest position.
If there is continuity, replace the +/- control button.
SUSPENDStatus ET703 becomes SUSPEND when the cruise control/speed limiter "0" button
is pressed. This button is located on the steering wheel, to the right.
To carry out the checks and measurements in complete safety, observe the driver's
frontal airbag removal recommendations (see MR 392 (Clio III), MR 385 (Modus),
MR 411 (New Twingo), or MR 442 (E33), Mechanical, 88C, Airbag and
pretensioners, Driver's frontal airbag: Removal - Refitting).
If status ET703 does not become SUSPEND, check the condition of the cruise
control/speed limiter "R/0" button and the condition of its connector.
If the connector is faulty and there is a repair method (see Technical Note 6015A,
Repairing electrical wiring, Wiring: Precautions for repair), repair the connector,
otherwise replace the wiring.
Measure the resistance of the following connection while pressing the "0" button
(on the button connections):
●86G of component 331.
●86M of component 331.
If the resistance is not X ≈ 0 Ω, replace the R/0 control button.
If there is continuity, replace the R/0 control button.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

17B-259V7 MR-413-X44-17B000$153.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET703
CONTINUED 4
RESUME
Status ET703 becomes RESUME when the cruise control/speed limiter "R" button is
pressed. This button is located on the steering wheel, to the right.
To carry out the checks and measurements in complete safety, observe the driver's
frontal airbag removal recommendations (see MR 392 (Clio III), MR 385 (Modus),
MR 411 (New Twingo), or MR 442 (E33), Mechanical, 88C, Airbag and
pretensioners, Driver's frontal airbag: Removal - Refitting).
If status ET703 does not change to RESUME, check the status of the cruise control/
speed limiter R/0 button and the condition of its connector.
If the connector is faulty and there is a repair method (see Technical Note 6015A,
Repairing electrical wiring, Wiring: Precautions for repair), repair the connector,
otherwise replace the wiring.
Measure the resistance of the following connection while pressing the R button
(on the button connections):
●86G of component 331.
●86M of component 331.
If the resistance is not X ≈ 900 Ω, check the continuity of the connection when the
button is in the rest position.
If there is continuity, replace the R/0 control button.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

17B-261V7 MR-413-X44-17B000$153.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET704
ET705
CONTINUED
Sensor electrical conformity
ACTIVE
or
INACTIVE
If the brake lights are working:
–Check the continuity and the absence of interference resistance of the
following connections:
●5A between components 160 and 120/645/119 (for NEW TWINGO or E33)
●65A between the components 160 and 120/645/119 (for CLIO III or MODUS).
If the connections are faulty and if there is a repair procedure (see Technical Note
6015A, Electrical wiring repair, Wiring: Precautions for repair), repair the wiring,
otherwise replace the wiring.
If the brake lights are not operational, check:
–the condition and fitting of the brake switch,
–the condition and conformity of the brake lights fuse.
–the conformity of the values in the following tables:
Continuity
between
connectionsInsulation
between
connections
Switch
pressed
(Brake pedal
released)For CLIO III or
MODUS5A and SP13 65G and AP10
For NEW
TWINGO or E335A and AP10 65A and AP10
Switch
released
(Brake pedal
depressed)For CLIO III or
MODUS65G and AP10 5A and SP13
For NEW
TWINGO or E3365A and AP10 5A and AP10
Replace the switch if the values obtained are not correct.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.