2009 RENAULT TWINGO RS air condition

PARKING DISTANCE CONTROL
Fault finding - Introduction
87F
87F - 3V2 MR-413-X44-87F000$066_eng.mif
Vdiag No.: 04 08
Faults
Faults are declared as either present or stored (depending on whether they appeared in a certain context and have
disappeared since, or whether they remain present but have not been diagnosed within the current context).
The present or stored status of faults should be taken into consideration when the diagnostic tool is used following
the + after ignition supply being switched on (without operating the system components).
For a present fault, apply the procedure described in the Interpretation of faults section.
For a stored fault, note the faults displayed and apply the instructions in the Notes section.
If the fault is confirmed when the instructions in the Notes section are applied, the fault is present. Deal with the fault
If the fault is not confirmed, check:
–the electrical lines which correspond to the fault,
–the connectors for these lines (for oxidation, bent pins, etc.),
–the resistance of the component detected as faulty,
–the condition of the wires (melted or split insulation, wear).
Conformity check
The aim of the conformity check is to check data that does not produce a fault on the diagnostic tool because the
data is inconsistent. Therefore, this stage is used to:
–carry out fault finding on faults that do not have a fault display, and which may correspond to a customer
complaint.
–check that the system is operating correctly and that there is no risk of a fault recurring after repairs.
This section gives the fault finding procedures for statuses and parameters and the conditions for checking them.
If a status is not behaving normally or a parameter is outside the permitted tolerance values, consult the
corresponding fault finding page.
Customer complaints - Fault finding chart
If the test with the diagnostic tool is OK but the customer complaint is still present, the fault should be processed by
customer complaints.
A synopsis of the general procedure to follow is provided on the following page in the
form of a flow chart.

PARKING DISTANCE CONTROL
Fault finding - Interpretation of faults
87F
87F - 14V2 MR-413-X44-87F000$462_eng.mif

Vdiag No.: 04 08
PARKING DISTANCE CONTROL
Fault finding - Interpretation of faults
DF002
PRESENT
OR
STOREDLEFT-HAND OUTER SENSOR
CC.1 : Short circuit to + 12 V
CO.0 : Open circuit or short circuit to earth
1.DEF : Internal electronic fault
NOTESConditions for applying the fault finding procedure to stored faults:
The fault is declared present following selection of reverse gear if the parking proximity
sensor function is ACTIVE (READY): the parking proximity sensor warning light is not
lit, see the interpretation of status ET003 Parking proximity sensor function.
Special notes:
This fault is indicated by the buzzer (a 5 second warning sound) and the system shuts
down.
CC.1
CO.0
NOTES None
Remove the rear bumper and disconnect the 3-track connector on the left-hand outer sensor.
Check for possible damage to the wiring harness, check the condition and connection of the parking distance
control computer and left-hand outer sensor connectors (bent, oxidised or broken tabs).
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Switch off the ignition and disconnect the computer's 16-track connector.
Measure the internal resistances of computer component code 12022 between the following connections:
●Connection code 151C,
●Connection code 151U.
The resistance must be 215 kΩΩ Ω Ω
± 10 kΩΩ Ω Ω
.
●Connection code 151C,
●Connection code 151V.
The resistance must be 100 kΩΩ Ω Ω
± 5 kΩΩ Ω Ω
.
If the readings do not correspond to the above values or if there is a short circuit in the specified connections,
contact Techline.
AFTER REPAIRClear the stored faults.
Follow the instructions to confirm repair.
Deal with any other faults.
AAP_V04_DEF002/AAP_V08_DEF002
MR-413-X44-87F000$462_eng.mif

PARKING DISTANCE CONTROL
Fault finding - Interpretation of faults
87F
87F - 16V2 MR-413-X44-87F000$462_eng.mif
Vdiag No.: 04 08
DF003
PRESENT
OR
STOREDLEFT-HAND INNER SENSOR
CC.1 : Short circuit to + 12 V
CO.0 : Open circuit or short circuit to earth
1.DEF : Internal electronic fault
NOTESConditions for applying the fault finding procedure to stored faults:
The fault is declared present following selection of reverse gear if the parking proximity
sensor function is ACTIVE (READY): the parking proximity sensor warning light is not
lit, see the interpretation of status ET003 Parking proximity sensor function.
Special notes:
This fault is indicated by the buzzer (a 5 second warning sound) and the system shuts
down.
CC.1
CO.0
NOTES None
Remove the rear bumper and disconnect the 3-track connector on the left-hand inner detection sensor.
Check for possible damage to the wiring harness, check the condition and connection of the parking distance
control computer and left hand inner sensor connectors (bent, oxidised or broken tabs).
If the connection is faulty (see Technical Note 6015A, Electrical wiring repair, Wiring: Precautions for repair),
repair the wiring, or replace it.
Switch off the ignition and disconnect the computer's 16-track connector.
Measure the internal resistances of the computer between the following connections:
●Connection code 151M,
●Connection code 151U.
The resistance must be 215 kΩΩ Ω Ω
± 10 kΩΩ Ω Ω
.
●Connection code 151M,
●Connection code 151V.
The resistance must be 100 kΩΩ Ω Ω
± 5 kΩΩ Ω Ω
.
If the readings do not correspond to the above values or if there is a short circuit in the specified connections,
contact Techline.
Measure the resistance of component 1221 between the following connections:
●Connection code 151M,
●Connection code 151U.
If the resistance value is not infinite, replace the left-hand inner sensor.
●Connection code 151M,
●Connection code 151V.
If the resistance is not 40 kΩΩ Ω Ω
± 5 kΩΩ Ω Ω
(wait a few seconds for the reading to stabilise), replace the left-hand inner
sensor.
AFTER REPAIRClear the stored faults.
Follow the instructions to confirm repair.
Deal with any other faults.
AAP_V04_DEF003/AAP_V08_DEF003

PARKING DISTANCE CONTROL
Fault finding - Interpretation of faults
87F
87F - 18V2 MR-413-X44-87F000$462_eng.mif
Vdiag No.: 04 08
DF004
PRESENT
OR
STOREDRIGHT-HAND OUTER SENSOR
CC.1 : Short circuit to + 12 V
CO.0 : Open circuit or short circuit to earth
1.DEF : Internal electronic fault
NOTESConditions for applying the fault finding procedure to stored faults:
The fault is declared present following selection of reverse gear if the parking proximity
sensor function is ACTIVE (READY): the parking proximity sensor warning light is not
lit, see the interpretation of status ET003 Parking proximity sensor function.
Special notes:
This fault is indicated by the buzzer (a 5 second warning sound) and the system shuts
down.
CC.1
CO.0
NOTES None
Remove the rear bumper and disconnect the 3-track connector on the right-hand outer detection sensor.
Check for possible damage to the wiring harness, check the condition and connection of the parking distance
control computer and right-hand outer sensor connectors (bent, oxidised or broken tabs).
If the connection is faulty (see Technical Note 6015A, Electrical wiring repair, Wiring: Precautions for repair),
repair the wiring, or replace it.
Switch off the ignition and disconnect the computer's 16-track connector.
Measure the internal resistances of the computer between the following connections:
Connection code 151H,
●Connection code 151U.
The resistance should be 215 kΩΩ Ω Ω
± 10 kΩΩ Ω Ω
.
●Connection code 151H,
●Connection code 151V.
The resistance should be 100 kΩΩ Ω Ω
± 5 kΩΩ Ω Ω
.
If the readings do not correspond to the above values or if there is a short circuit in the specified connections,
contact Techline.
Measure the resistance of component 1219 between the following connections:
●Connection code 151H,
●Connection code 151U.
If the resistance value is not infinite, replace the right-hand outer sensor.
●Connection code 151H,
●Connection code 151V.
If the resistance is not 40 kΩΩ Ω Ω
± 5 kΩΩ Ω Ω
(wait a few seconds for the reading to stabilise), replace the right-hand outer
sensor.
AFTER REPAIRClear the stored faults.
Follow the instructions to confirm repair.
Deal with any other faults.
AAP_V04_DEF004/AAP_V08_DEF004

PARKING DISTANCE CONTROL
Fault finding - Interpretation of faults
87F
87F - 20V2 MR-413-X44-87F000$462_eng.mif
Vdiag No.: 04 08
DF005
PRESENT
OR
STOREDRIGHT-HAND INNER SENSOR
CC.1 : Short circuit to + 12 V
CO.0 : Open circuit or short circuit to earth
1.DEF : Internal electronic fault
NOTESConditions for applying the fault finding procedure to stored faults:
The fault is declared present following selection of reverse gear if the parking proximity
sensor function is ACTIVE (READY): the parking proximity sensor warning light is not
lit, see the interpretation of status ET003 Parking proximity sensor function.
Special notes:
This fault is indicated by the buzzer (a 5 second warning sound) and the system shuts
down.
CC.1
CO.0
NOTES None
Remove the rear bumper and disconnect the 3-track connector on the right-hand inner detection sensor.
Check for possible damage to the wiring harness, check the condition and connection of the parking distance
control computer and the right hand inner sensor connectors (bent, oxidised or broken tabs).
If the connection is faulty (see Technical Note 6015A, Electrical wiring repair, Wiring: Precautions for repair),
repair the wiring, or replace it.
Switch off the ignition and disconnect the computer's 16-track connector.
Measure the internal resistances of the computer between the following connections:
Connection code 151Q,
●Connection code 151U.
The resistance should be 215 kΩΩ Ω Ω
± 10 kΩΩ Ω Ω
.
●Connection code 151Q,
●Connection code 151V.
The resistance should be 100 kΩΩ Ω Ω
± 5 kΩΩ Ω Ω
.
If the readings do not correspond to the above values or if there is a short circuit in the specified connections,
contact Techline.
Measure the resistance of component 1220 between the following connections:
●Connection code 151Q,
●Connection code 151U.
If the resistance value is not infinite, replace the right-hand inner sensor.
●Connection code 151Q,
●Connection code 151V.
If the resistance value is not 40 kΩΩ Ω Ω
± 5 kΩΩ Ω Ω
(wait a few seconds for the reading to stabilise), replace the right-hand
inner sensor.
AFTER REPAIRClear the stored faults.
Follow the instructions to confirm repair.
Deal with any other faults.
AAP_V04_DEF005/AAP_V08_DEF005

PARKING DISTANCE CONTROL
Fault finding - Interpretation of faults
87F
87F - 22V2 MR-413-X44-87F000$462_eng.mif
Vdiag No.: 04 08
DF006
PRESENT
OR
STOREDBUZZER
CC.1 : Short circuit to + 12 V
CO.0 : Open circuit or short circuit to earth
NOTESConditions for applying the fault finding procedure to stored faults:
The fault is declared present following selection of reverse gear if the parking proximity
sensor function is ACTIVE (READY): the parking proximity sensor warning light is not
lit, see the interpretation of status ET003 Parking proximity sensor function.
Special notes:
The fault is indicated by the absence of the 1-second beep normally emitted by the
buzzer when reverse gear is selected.
Check for possible damage to the wiring harness, check the condition and connection of the parking distance
control computer and the buzzer connectors (bent, oxidised or broken tabs).
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Switch off the ignition and disconnect the 16 track connector from computer component code 1222.
Measure the internal resistance of the computer between the following connections:
●Connection code 151R.
●Connection code 151S
Between components 1222 and 1223.
If the measured value is not 314 ΩΩ Ω Ω

± 10 ΩΩ Ω Ω
or if there is a short circuit on the specified connections, contact Techline.
Switch off the ignition, and disconnect the parking distance control computer to check the insulation, continuity
and the absence of interference resistance on the following connections:
●Connection code 151R,
●Connection code 151S.
Between components 1222 and 1223.
If the connection or connections are faulty and if there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring or replace it.
Measure the resistance value of component 1223 between the following connections:
Measure the resistance between the following connections:
●Connection code 151R,
●Connection code 151S.
Replace the buzzer if its resistance value is not approximately 48 ΩΩ Ω Ω
± 5 ΩΩ Ω Ω
.
If the fault is still present, replace the buzzer.
AFTER REPAIRClear the stored faults.
Follow the instructions to confirm repair.
Deal with any other faults.
AAP_V04_DEF006/AAP_V08_DEF006

PARKING DISTANCE CONTROL
Fault finding - Interpretation of faults
87F
87F - 23V2 MR-413-X44-87F000$462_eng.mif
Vdiag No.: 04 08
DF007
PRESENT
OR
STOREDSENSOR SUPPLY VOLTAGE
CC.0: Short circuit to earth
NOTESConditions for applying the fault finding procedure to stored faults:
The fault reappears present or stored after its has been cleared, the ignition is switched
on and off again and reverse gear is selected.
Special notes:
The sensors are directly supplied with + 12 V by the computer.
With the parking proximity sensor computer 16-track connector connected and with the ignition on, measure the
sensor power supply coming from the computer. The voltage should be equal to the battery voltage (± 0.5 V)
when measuring between connections 151U (+ 12 V) and 151V (earth).
If there is no + 12 V supply between connections 151U and 151V, remove the rear bumper to access the sensors.
Switch off the ignition, and disconnect the parking proximity sensor computer to check the insulation and
continuity and the absence of interference resistance on the following connections:
●Connection code 151U,
●Connection code 151V.
Between components 1222 and 1218, 1219, 1220, 1221.
If the connection or connections are faulty and if there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring or replace it.
If the sensor power supply is correct (no short circuit), reconnect the computer connector and four sensor
connectors.
Turn on the ignition and disconnect the sensors, one at a time, to see if any of the sensors causes the power supply
to drop. Replace the defective sensor.
If the sensor supply lines are not correct, check the presence and condition of fuse F6 (15A); replace it if necessary.
Check for the + 12 V supply on connection AP3 between components of component 1222 and 1016. Check for
earth on connection MG between components 1222 and earth MG.
If the fault is still present, contact the Techline.
AFTER REPAIRClear the stored faults.
Follow the instructions to confirm repair.
Deal with any other faults.
AAP_V04_DEF007/AAP_V08_DEF007

PARKING DISTANCE CONTROL
Fault finding - Interpretation of faults
87F
87F - 24V2 MR-413-X44-87F000$462_eng.mif
Vdiag No.: 04 08
DF008
PRESENT
OR
STOREDCOMPUTER FAULT
1.DEF : Internal electronic fault
NOTESConditions for applying the fault finding procedure to stored faults:
The fault reappears present or stored after its has been cleared, the ignition is switched
on and off again and reverse gear is selected.
Special notes:
If the fault is present and is represented by 1.DEF or 2.DEF, the system operates in
defect mode (substitute values are used).
1.DEF
NOTES None
After following the instructions, if the fault recurs, switch off the ignition and disconnect the supply fuse from the
parking distance control computer F6 (15A).
Reconnect the fuse, switch the ignition back on, and perform a fault reading.
If the fault recurs, check the connections and condition of the parking proximity sensor computer connector (no
damage to the connections).
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
With the ignition switched off, disconnect the parking proximity sensor computer connector to check the
conformity of the feeds and to check the insulation, continuity and the absence of interference resistance
on the following connections:
Connection code AP3,
Between components 1222 and 1016.
Connection code MG.
Between component 1222 and the rear left-hand earth.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact the Techline.
AFTER REPAIRClear the stored faults.
Follow the instructions to confirm repair.
Deal with any other faults.
AAP_V04_DEF008/AAP_V08_DEF008