2009 RENAULT TWINGO RS ignition

36B-26
MR-413-X44-36B000$536.mif
V2
POWER – ASSISTED STEERING
Fault finding – Conformity check
EPAS
Vdiag No.: 04 - 08
36B
SUB-FUNCTION: ASSISTANCE
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool.
Application conditions: ignition on, engine stopped, no movement of
the steering wheel, front wheels set straight ahead.
FunctionParameter or Status
Checked or ActionDisplay and notes Fault finding
Power supplyPR032:Feed voltage0 VIn the event of a fault on this
parameter, apply the fault finding
procedure of DF037 Battery voltage.
Wire informationPR003:Vehicle speed0 mphIn the event of a fault, apply the
interpretation of parameter PR003.
PR004:Engine speed0 rpmIn the event of a fault, apply the
interpretation of parameter PR004.
Steering wheel
angle
(Vdiag 04 only)ET020:Steering
wheel angle
sensor
programmingNot programmedIn the event of a fault, apply the
interpretation of status ET020.
PR121:Steering
wheel angle- 5˚ < X < 5˚In the event of a fault, apply the
interpretation of parameter PR121.
FaultsET021:Motor thermal
protection
indicatorNot activeIn the event of a fault, apply the
interpretation of status ET021.
ET025:Fault indicatorOffIn the event of a fault, apply the
interpretation of status ET025.

36B-27
MR-413-X44-36B000$536.mif
V2
POWER – ASSISTED STEERING
Fault finding – Conformity check
EPAS
Vdiag No.: 04 - 08
36B
SUB-FUNCTION: ASSISTANCE (CONTINUED)
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool.
Application conditions: ignition on, engine stopped, no movement of the
steering wheel, front wheels set straight ahead.
FunctionParameter or Status
Checked or ActionDisplay and notes Fault finding
AssistancePR001:Torque applied
to the steering
wheel0 Nm (+ 0.2 Nm)In the event of a fault, apply the
interpretation of parameter
PR001.
OutputPR132:Current setpoint
(45 A)0 A
Note: these two
parameters must be
approximately the
same.In the event of a fault, apply the
interpretation of parameters
PR132 and PR130.
PR130:Motor power
(45 A)
PR131:Current setpoint
(60 A)0 A
Note: these two
parameters must be
approximately the
same.In the event of a fault, apply the
interpretation of parameters
PR131 and PR129.
PR129:Motor power
(60 A)

36B-32
MR-413-X44-36B000$670.mif
V2
36B
POWER – ASSISTED STEERING
Fault finding – Interpretation of statuses
ET020
PROGRAMMING THE STEERING WHEEL ANGLE SENSOR
NOTESNote:
Deal first with DF038 Angle sensor.
Special note:
Every time the ignition is switched on, status ET020 is NOT PROGRAMMED.
Programming is performed automatically each time the vehicle is driven.
Drive the vehicle, then switch off the ignition and check that status ET020 is PROGRAMMED.
If status ET020 remains NOT PROGRAMMED after the vehicle is driven, carry out the fault finding procedure for
fault DF038 Angle sensor.
AFTER REPAIRPerform a test using the diagnostic tool.
DAE_V04_ET020
EPAS
Vdiag No.: 04
MR-413-X44-36B000$670.mif

36B-43
MR-413-X44-36B000$938.mif
V2
36B
POWER – ASSISTED STEERING
Fault finding – Fault finding Chart
ALP 1 No dialogue with the computer
NOTESUse the Technical Note wiring diagram for New Twingo.
Try to establish dialogue with a computer on another vehicle to check that the diagnostic tool is not faulty.
If the tool is not faulty and no dialogue is established with any other computer of the same vehicle, check the
tightness and condition of the battery terminals (see 80A, Battery).
Check the charging circuit (see 16A, Starting - Charging).
With connector A of component 502 and the connector of components 1222 and 1094 disconnected, check the
continuity and insulation of connection HK between components 502 and 225.
If the connection(s) are faulty and there is a repair method (see Technical Note 6015A, Repairing electrical
wiring, W iring: Precautions for repair), repair the wiring, otherwise replace it.
If the checks reveal no faults, check the conformity of components 1022 and 1094.
Check the condition and the position of the 80 A fuse in the engine fuse and relay box.
Check the condition and the position of fuse F3 (15 A) in the passenger compartment fuse box.
With the ignition on and the engine stopped, check for a voltage equal to the battery voltage on connections BP81
and AP23 against earth ML.
Connectors of component 502 disconnected, check the condition and conformity of the connectors and clips.
If the connector is faulty (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for
repair), repair the connector, otherwise replace the wiring.
With the connectors of components 597 and 1016 disconnected:
Check the continuity and insulation of connection BP81 between components 502 and 597.
Check the continuity and insulation of connection AP23 between components 502 and 1016.
Check the continuity and insulation of connection ML of component 502.
If the connection(s) are faulty and there is a repair method (see Technical Note 6015A, Repairing electrical
wiring, W iring: Precautions for repair), repair the wiring, otherwise replace it.
If the checks reveal no faults, check the conformity of components 597 and 1016.
If the fault is still present, contact Techline.
AFTER REPAIRPerform a test using the diagnostic tool.
DAE_V04_ALP1/ DAE_V08_ALP1
EPAS
Vdiag No.: 04 - 08
MR-413-X44-36B000$938.mif