2009 RENAULT TWINGO RS air

38C-54
MR-413-X44-38C000$658_eng.mif
V1
MK70 ABS
Vdiag No: 04ANTI-LOCK BRAKING SYSTEM
Fault finding - Interpretation of statuses38C
ET017
CONTINUED 1
Connectors of components 645, 172, 173, 639 and 1094, intermediate connectors
R107 and R15 and connector of component 119 (if present on the vehicle)
disconnected from connection 65A:
–Check the insulation of connection 65A between component 160 and
intermediate connector R107.
–Check the insulation of connection 65A between component 172 and
intermediate connector R107.
–Check the insulation of connection 65A between component 173 and
intermediate connector R107.
–Check the insulation of connection 65A between intermediate connectors R107
and R15.
–Check the insulation of connection 65A between component 639 and
intermediate connector R15.
–Check the insulation of connection 65A between component 645 and
intermediate connector R107.
If the connector is faulty (see NT6015, Repairing electrical wiring, wiring:
Precaution for repairs), repair the connector, otherwise replace the wiring.
–Check for + 12 V after ignition feed on connection AP10 of component 1016 to
earth MAH.
If the checks reveal no faults, carry out a check of each component associated with
connection 65A and AP10 (short circuits).
Check the condition and positioning of the F5 5A fuse (see MR411 Mechanical
systems, 81C, Fuses: 16A).
–Check the condition, mounting and adjustment of the brake light switch and the
conformity of the bulbs.
–Remove the brake light switch and check that it is operating correctly:
Connection continuity Connection insulation
Switch pressed
(Brake pedal released)AP10 and 5A AP10 and 65A
Switch released
(Brake pedal
depressed)AP10 and 65A AP10 and 5A
–Replace the switch if necessary.
Connectors of components 645, 172, 173, 639 and 1094, intermediate
connectors R107 and R15 and connector of component 119 (if present on the vehicle)
disconnected from connection 65A
–Check the insulation of connection 65A between component 160 and
intermediate connector R107.
STATUS
DEPRESSED:
Brake pedal
released
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.

38C-55
MR-413-X44-38C000$658_eng.mif
V1
ANTI-LOCK BRAKING SYSTEM
Fault finding - Interpretation of statuses
MK70 ABS
Vdiag No: 04
38C
ET017
CONTINUED 2
–Check the insulation of connection 65A between component 172 and intermediate connector R107.
–Check the insulation of connection 65A between component 173 and intermediate connector R107.
–Check the insulation of connection 65A between intermediate connectors R107 and R15.
–Check the insulation of connection 65A between component 639 and intermediate connector R15.
–Check the insulation of connection 65A between component 645 and intermediate connector R107.
If the connector is faulty (see NT6015, Repairing electrical wiring, wiring: Precaution for repairs),
repair the connector, otherwise replace the wiring.
If the checks reveal no faults, carry out a check of each component associated with connection 65A
(internal component faults).
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.

38C-56
MR-413-X44-38C000$705_eng.mif
V1
38C
ANTI-LOCK BRAKING SYSTEM
Fault finding - Dealing with computer statuses and parameters
PARAMETERS
PR001: Front right-hand wheel speed.
PR002: Front left-hand wheel speed.
PR003: Rear right-hand wheel speed.
PR004: Rear left-hand wheel speed.
These parameters indicate the speed in mph (km/h) of each wheel on the vehicle.
PR005: Computer supply voltage.
This parameter indicates the computer supply voltage in volts.
PR030: Tachometric index.
This parameter specifies the tachometric index entered in the computer for the tyres fitted to the vehicle.
PR038: Vehicle speed.
This parameter indicates the vehicle speed in mph (km/h).
PR063: Vehicle parameters.
This parameter shows whether the configuration (VP004 "Vehicle parameters") matches the vehicle
undergoing fault finding.
STATUS
ET017: Brake pedal
This status gives the position (depressed or released) of the brake pedal
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
MK70 ABS
Vdiag No: 04
MR-413-X44-38C000$705_eng.mif

38C-57
MR-413-X44-38C000$752_eng.mif
V1
38C
ANTI-LOCK BRAKING SYSTEM
Fault finding - Dealing with command modes
CLEARING
RZ001: Fault memory.
This command is used for clearing the computer's stored faults.
SPECIAL COMMANDS
SC001: Check target teeth.
This command tests the condition of the teeth on each wheel.
Select command SC001 "Check target teeth" and follow the instructions.
The test result should indicate 48 sprockets.
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
MK70 ABS
Vdiag No: 04
MR-413-X44-38C000$752_eng.mif

38C-58
MR-413-X44-38C000$799_eng.mif
V1
38C
ANTI-LOCK BRAKING SYSTEM
Fault finding - Command summary table
Tool command Diagnostic tool title
AC003Front left-hand wheel solenoid valves
AC004Front right-hand wheel solenoid valves
AC005Rear left-hand wheel solenoid valves
AC006Rear right-hand wheel solenoid valves
AC016Pump motor test
AC153Bleed front left-hand wheel
AC154Bleed front right-hand wheel
AC155Bleed rear left-hand wheel
AC156Bleed rear right-hand wheel
AC195Vehicle speed signal
AC196Hazard warning light activation request
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
MK70 ABS
Vdiag No: 04
MR-413-X44-38C000$799_eng.mif

38C-59
MR-413-X44-38C000$846_eng.mif
V1
38C
ANTI-LOCK BRAKING SYSTEM
Fault finding - Dealing with command modes
AC003
AC004
AC005
AC006FRONT LEFT-HAND WHEEL SOLENOID VALVES
FRONT RIGHT-HAND WHEEL SOLENOID VALVES
REAR LEFT-HAND WHEEL SOLENOID VALVES
REAR RIGHT-HAND WHEEL SOLENOID VALVES
NOTESConditions of use of the command.
Ignition on, engine stopped and vehicle speed zero.
Before using the commands, check that the battery is fully charged.
The previous 4 commands allow the hydraulic check of each wheel.
Raise the vehicle in order to be able to rotate the wheels, and check that they rotate freely.
Keep the brake pedal depressed to prevent the wheel being tested from being turned by hand (do not brake so
firmly that full braking power is reached).
Select and confirm the command of the wheel being examined (e.g. Front left-hand wheel solenoid valves, etc.)
Turn the wheel concerned by hand; 5 locking/unlocking cycles should be noted on the wheel.
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
ABS_V04_AC003 / ABS_V04_AC004
ABS_V04_AC005 / ABS_V04_AC006
MK70 ABS
Vdiag No: 04
MR-413-X44-38C000$846_eng.mif

38C-60
MR-413-X44-38C000$846_eng.mif
V1
ANTI-LOCK BRAKING SYSTEM
Fault finding - Dealing with command modes
MK70 ABS
Vdiag No: 04
38C
AC016
PUMP MOTOR TEST
NOTESConditions of use of the command.
Ignition on, engine stopped and vehicle speed zero.
Before using the command, check that the battery is fully charged.
This command is used to test the pump motor control circuit.
Select command AC016 Pump Motor Test.
The motor must run for 5 seconds.
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
ABS_V04_AC016

38C-61
MR-413-X44-38C000$846_eng.mif
V1
ANTI-LOCK BRAKING SYSTEM
Fault finding - Dealing with command modes
MK70 ABS
Vdiag No: 04
38C
AC153
AC154
AC155
AC156BLEED FRONT LEFT-HAND WHEEL
BLEED FRONT RIGHT-HAND WHEEL
BLEED REAR LEFT-HAND WHEEL
BLEED REAR RIGHT-HAND WHEEL
NOTESConditions of use of the command.
Ignition on, engine stopped and vehicle speed zero.
Before using the commands, check that the battery is fully charged.
These 4 commands should only be used if you observe lengthening of the brake pedal travel during a road test
with ABS regulation (the system should have been bled in advance using the conventional procedure).
See ALP8.
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
ABS_V04_AC153 / ABS_V04_AC154
ABS_V04_AC155 / ABS_V04_AC156