2009 RENAULT TWINGO air condition

62B-47
MR-413-X44-62B000$552_eng.mif
V1
CLIMATE CONTROL
Fault finding - Interpretation of statuses

Vdiag No.: 44
62B
ET085
HEATED REAR SCREEN: AUTO MODE
NOTESNone
This status specifies whether the heated rear screen is operated in automatic mode or not. This mode
corresponds to the SEE CLEAR function. This function switches on the heated rear screen, the heated door
mirrors, the air conditioning and the windscreen ventilation. The heating and air conditioning system requires a
short amount of time between the request and blower activation in order for dry air to be blown. The heated rear
screen will operate for as long as the SEE CLEAR function is requested (permanently controlled). This automatic
mode is obtained by pressing the de-icing button at the top of the air conditioning control panel.
If the SEE CLEAR function is requested, the status should display ACTIVE.
If the SEE CLEAR function is not requested, the status should display INACTIVE.
If the status does not operate as indicated (see ALP10 Poor de-icing efficiency - rear screen demisting).
AFTER REPAIRRepeat the conformity check from the start.
CLIM_V44_ET085

62B-48
MR-413-X44-62B000$552_eng.mif
V1
CLIMATE CONTROL
Fault finding - Interpretation of statuses

Vdiag No.: 44
62B
ET086
HEATED REAR SCREEN: MANUAL MODE
NOTESNone
This status specifies whether the request for the heated rear screen is being operated in manual mode. This mode
corresponds to a timed operating period for the heated rear screen, controlled by the UCH. This time delay
depends on the exterior temperature (between 10 and 15 minutes).
Operation in manual mode is obtained by pressing the de-icing button at the bottom of the air conditioning control
panel. This function is used to switch on the heated rear screen and the heated door mirrors.
If activation of the heated rear screen is requested in manual mode, the status should display ACTIVE.
If activation of the heated rear screen is not requested, the status should display: INACTIVE.
If the status does not operate as indicated (see ALP10 Poor de-icing efficiency - rear screen demisting).
AFTER REPAIRRepeat the conformity check from the start.
CLIM_V44_ET086

62B-49
MR-413-X44-62B000$552_eng.mif
V1
CLIMATE CONTROL
Fault finding - Interpretation of statuses

Vdiag No.: 44
62B
ET140
AIR CONDITIONING REQUEST
NOTESNote:
For more information, refer to the flowchart for the request to switch on the
compressor (see Air conditioning, General operating mode).
This status specifies whether the request to switch on the compressor has been sent by the climate control
computer to the UCH or not.
When activation of the air conditioning is requested, the status should display ACTIVE.
When activation of the air conditioning is not requested, the status should display INACTIVE.
If the status does not operate as indicated, contact your Techline.
AFTER REPAIRRepeat the conformity check from the start.
CLIM_V44_ET140

62B-50
MR-413-X44-62B000$552_eng.mif
V1
CLIMATE CONTROL
Fault finding - Interpretation of statuses

Vdiag No.: 44
62B
ET141
PASSENGER COMPARTMENT FAN
NOTESSpecial note:
This status is used by the UCH to authorise the request for air conditioning which is
sent to the injection. The UCH sends this signal to the injection to authorise the
request to activate the passenger compartment heating resistors (only on diesel
version): operating safety.
This status shows the operation of the passenger compartment blower.
When the passenger compartment blower is operating (from speed 1 to speed 8), the status displays: RUNNING.
When the passenger compartment blower is not operating (speed 0), the status displays STOPPED.
If the status does not operate as displayed, check that the passenger compartment blower is operating correctly.
If the passenger compartment blower does not work, apply the fault finding procedure in Fault finding chart
(ALP) 5 No passenger compartment ventilation.
If the passenger compartment blower operates correctly but the status displays the message OFF, check that the
passenger compartment blower visual feedback (spiral symbol) on the control panel works correctly (increase in
spiral bargraphs according to the eight speeds).
If the passenger compartment visual feedback (blade symbol) on the instrument panel does not work, contact
your Techline.
If the fault is still present, perform fault finding on the multiplex network (see 88B, Multiplexing).
AFTER REPAIRRepeat the conformity check from the start.
CLIM_V44_ET141

62B-59
MR-413-X44-62B000$644_eng.mif
V1
CLIMATE CONTROL
Fault finding - Interpretation of parameters
Vdiag No.: 44
62B
PR092
BATTERY VOLTAGE
NOTESUse the Wiring Diagram Technical Note for the New Twingo.
This parameter specifies the supply voltage of the climate control computer.
This parameter must display a voltage equal to: 10.5 V < X < 14.4 V with the engine running.
Using a multimeter, check the consistency of the parameter by measuring the voltage across the battery
terminals.
If the parameter corresponds with the voltage measured on the battery terminals, run fault finding on the electric
charging circuit.
If the parameter does not correspond with the battery voltage, check the condition and position of fuse F29 (15A)
in the passenger compartment fuse unit.
Consult section 81C Fuses.
Disconnect the connectors of the following components of connection SP2:
●Component connector 615
●Component connector 419
●Component connector 645
●Component connector 319
●Component connector 261
●Component connector 653
●Component connector 1428
With connector A of component 419 disconnected, check the insulation and continuity of connection SP2
between components 419 and 1016.
If the connection or connections are faulty (see Technical Note 6015A, Repairing electrical wiring, Wiring:
Precautions for repair), repair the wiring, otherwise replace it.
Check the vehicle earth connection NAM of the connector of component 419.
If the connection is faulty (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for the
repair), repair the wiring, otherwise replace the wiring.
If these checks do not reveal any faults, carry out a test on each of the components involved in connection
SP2 (short circuit).
AFTER REPAIRRepeat the conformity check from the start.
CLIM_V44_PR092

62B-60
MR-413-X44-62B000$644_eng.mif
V1
CLIMATE CONTROL
Fault finding - Interpretation of parameters
Vdiag No.: 44
62B
PR122
NIGHT LIGHTING LEVEL
NOTESThe climate control computer receives the dimmer lighting level via the instrument
panel through the multiplex line.
This parameter indicates the dimmer lighting level as a percentage.
If this parameter appears inconsistent with the air conditioning control panel lighting, contact Techline.
AFTER REPAIRRepeat the conformity check from the start.
CLIM_V44_PR122

62B-62
MR-413-X44-62B000$736_eng.mif
V1
62B
CLIMATE CONTROL
Fault finding - Interpretation of commands
AC001
PASSENGER COMPARTMENT BLOWER UNIT
NOTESNone
This command is used to ensure that the passenger compartment blower is working. When this command is run
the passenger compartment blower comes on.
If the command does not operate as indicated, consult Fault finding chart 5 No passenger compartment
ventilation.
AFTER REPAIRCheck that the air conditioning function operates correctly.
CLIM_V44_AC001

Vdiag No.: 44
MR-413-X44-62B000$736_eng.mif

62B-63
MR-413-X44-62B000$736_eng.mif
V1
CLIMATE CONTROL
Fault finding - Interpretation of commands

Vdiag No.: 44
62B
AC002
AC003
RECIRCULATION MOTOR: EXTERIOR AIR
RECIRCULATION MOTOR: RECIRCULATION
NOTESWARNING
Do not touch the flap when running the command.
NOTE
The flap is located behind the cabin filter.
This command is used to actuate the air recirculation motor to check that it is working.
When running command AC003, the flap closes. When running command AC002, the flap opens.
If the command does not work as shown, check the mechanical condition of the flap.
If the fault is still present, apply the interpretation of fault DF021 Recirculation motor circuit.
AFTER REPAIRCheck that the air conditioning function operates correctly.
CLIM_V44_AC002 / CLIM_V44_AC003