2009 RENAULT TWINGO wheel bolts

12A-55
FUEL MIXTURE
Exhaust manifold: Removal - Refitting
K4M
12A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (02A, Lifting equipment).
aDisconnect the battery (see Battery: Removal - Re-
fitting) (80A, Battery).
aRemove:
-the engine undertray,
-the front right-hand wheel (see Wheel: Removal -
Refitting) (35A, Wheels and tyres),
-the windscreen wiper arms (see Windscreen wip-
er arm: Removal - Refitting) (85A, Wiping -
Washing),
-the scuttle panel grille (see Scuttle panel grille:
Removal - Refitting) (56A, Exterior equipment),
-the scoop under the scuttle panel grille (see Scoop
under the scuttle panel grille: Removal - Refit-
ting) (56A, Exterior equipment).
aDrain the gearbox (see Manual gearbox oils:
Draining - Filling) (21A, Manual gearbox).aRemove:
-the front right-hand wheel driveshaft (see Front
right-hand driveshaft: Removal - Refitting)
(29A, Driveshafts),
-the lower engine tie-bar (see 19D, Engine mount-
ing, Lower engine tie-bar: Removal - Refitting,
page 19D-18) ,
-the upstream expansion chamber (see 19B, Ex-
haust, Expansion chamber: Removal - Refit-
ting, page 19B-23) .
aRemove:
-the bolts (1) from the driveshaft relay bearing,
-the driveshaft relay bearing. Tightening torquesm
exhaust manifold studs9 N.m
heat shield bolts12 N.m
upstream and down-
stream oxygen sensors44 N.m
strut mounting bolt on
the cylinder block75 N.m
upstream strut bolt (ini-
tial torque)14 N.m
exhaust manifold nuts26 N.m
upstream and down-
streamstrut bolts44
N.m
upstream strut bolts44 N.m
driveshaft relay bearing
bolts21 N.m
IMPORTANT
Wear cut-resistant gloves during the operation.
131770

12A-60
FUEL MIXTURE
Exhaust manifold: Removal - Refitting
K4M
12A
-the driveshaft relay bearing.
aTorque tighten the driveshaft relay bearing bolts
(21 N.m).
aRefit:
-the upstream expansion chamber (see 19B, Ex-
haust, Expansion chamber: Removal - Refit-
ting, page 19B-23) ,
-the lower engine tie-bar (see 19D, Engine mount-
ing, Lower engine tie-bar: Removal - Refitting,
page 19D-18) ,
-the front right-hand wheel driveshaft (see Front
right-hand driveshaft: Removal - Refitting)
(29A, Driveshafts).
aFill the gearbox (see Manual gearbox oils: Drain-
ing - Filling) (21A, Manual gearbox).
aRefit:
-the scoop under the scuttle panel grille (see Scoop
under the scuttle panel grille: Removal - Refit-
ting) (56A, Exterior equipment),
-the scuttle panel grille (see Scuttle panel grille:
Removal - Refitting) (56A, Exterior equipment),
-the windscreen wiper arms (see Windscreen wip-
er arm: Removal - Refitting) (85A, Wiping -
Washing),
-the front right-hand wheel (see Wheel: Removal -
Refitting) (35A, Wheels and tyres),
-the engine undertray.
aConnect the battery (see Battery: Removal - Refit-
ting) (80A, Battery).

12B-8
TURBOCHARGING
Turbocharger: Removal - Refitting
D4F, and 780 or 782
12B
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (02A, Lifting equipment).
aDisconnect the battery (see Battery: Removal - Re-
fitting) (80A, Battery).
aRemove the engine undertray.
aDrain the manual gearbox (see Manual gearbox
oils: Draining - Filling) (21A, Manual gearbox).
aRemove:
-the air filter unit (see 12A, Fuel mixture, Air filter
unit: Removal - Refitting, page 12A-13) ,
-the upstream oxygen sensor (see 17B, Petrol in-
jection, Oxygen sensors: Removal - Refitting,
page 17B-13) ,
-the lower engine tie-bar (see 19D, Engine mount-
ing, Lower engine tie-bar: Removal - Refitting,
page 19D-18) ,
-the front right-hand wheel driveshaft (see Front
right-hand driveshaft: Removal - Refitting)
(29A, Driveshafts),
-the catalytic converter (see 19B, Exhaust, Cata-
lytic converter: Removal - Refitting, page 19B-
12) .II - OPERATION FOR REMOVAL OF PART
CONCERNED
aRemove the turbocharger oil return pipe (see 12B,
Turbocharging, Turbocharger oil pipe: Removal
- Refitting, page 12B-12) .
aFit the tools (Ms. 583) onto the turbocharger cooling
hoses (6) .
aRemove the turbocharger cooling hose clips using
the tool (Mot. 1448).
aDisconnect the turbocharger cooling hoses.
aRemove the turbocharger cooling pipe strut bolt (7) .
aRemove the turbocharger oil supply pipe (see 12B,
Turbocharging, Turbocharger oil pipe: Removal
- Refitting, page 12B-12) . Special tooling required
Ms. 583Pipe clamps .
Mot. 1448Remote operation pliers for
hose clips .
Tightening torquesm
turbocharger nuts21 N.m
turbocharger cooling
pipe hollow bolts30 N.m
turbocharger cooling
pipe bracket bolts10 N.m
IMPORTANT
Wear cut-resistant gloves during the operation.121773

12B-18
TURBOCHARGING
Intercooler: Removal - Refitting
D4F, and 780 or 782 – K9K, and 718
12B
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (02A, Lifting equipment).
aRemove:
-the front wheels (see Wheel: Removal - Refitting)
(35A, Wheels and tyres),
-the front wheel arch liners (see Front wheel arch
liner: Removal - Refitting) (55A, Exterior protec-
tion),
-the front bumper (see Front bumper: Removal -
Refitting) (55A, Exterior protection).
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aRemove the intercooler bolts (1) .
aLoosen the clip on the intercooler air outlet pipe (2) .
aDisconnect the intercooler air outlet pipe.
aUnclip the turbocharger air outlet pipe (3) .
aDisconnect the turbocharger air outlet pipe.
aRemove:
-the intercooler,
-the air deflector clips,
-the air deflector,
-the metal mounting.
REFITTING
I - REFITTING PREPARATION OPERATION
aCheck that the intercooler is not full of oil. In this
case, clean it with cleaning agent and let it dry (see
Vehicle: Parts and consumables for the repair)
(04B, Consumables - Products).
II - REFITTING OPERATION FOR PART
CONCERNED
aRefit:
-the metal mounting,
-the air deflector,
-the air deflector clips,
-the intercooler.
aConnect the turbocharger air outlet pipe.
aClip on the turbocharger air outlet pipe.
aConnect the intercooler air outlet pipe.
aTighten the clip on the intercooler outlet pipe.
aRefit the intercooler bolts.
III - FINAL OPERATION
aRefit:
-the front bumper (see Front bumper: Removal -
Refitting) (55A, Exterior protection),
-the front wheel arch liners (see Front wheel arch
liner: Removal - Refitting) (55A, Exterior protec-
tion),
-the front wheels (see Wheel: Removal - Refitting)
(35A, Wheels and tyres).
122830

14A-6
ANTIPOLLUTION
Fuel vapour absorber: Removal - Refitting
D4F, and SOUTH AFRICA
14A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting)
aDisconnect the battery (see Battery: Removal - Re-
fitting)
aRemove the rear left-hand wheel (see Wheel: Re-
moval - Refitting)
aRemove the rear left-hand wheel arch liner (see ) II - OPERATION FOR REMOVAL OF PART
CONCERNED
aUnclip the petrol vapour absorber pipe.
aRemove:
-the petrol vapour absorber bolts.
-the petrol vapour absorber.
REFITTING
REFITTING OPERATION FOR PART CONCERNED
aRefit.
-the petrol vapour absorber.
-the petrol vapour absorber bolts
aClip on the petrol vapour absorber pipe.
FINAL OPERATION
aRefit the rear left-hand wheel arch liner (see )
aRefit the rear left-hand wheel (see Wheel: Removal
- Refitting)
aReconnect the battery (see Battery: Removal - Re-
fitting) IMPORTANT
During this oper ation, be sure to:
-refrain from smoking or bringing red hot objects
close to the working area,
-be careful of fuel splashes when disconnecting the
union.
IMPORTANT
Wear goggles with side protectors for this opera-
tion.
IMPORTANT
Wear leaktight gloves (Nitrile type) for this opera-
tion.
WARNING
To avoid any corrosion or damage, protect the
areas on which fuel is likely to run.
WARNING
Keep the pipe unions away from contaminated
areas.
WARNING
To prevent impurities from entering the circuit, place
protective plugs on all fuel circuit components
exposed to the open air.
143884

16A-1
STARTING - CHARGING
Alternator: Removal - Refitting
D4F or D7F, and STANDARD HEATING
16A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aDisconnect the battery (see ) (MR 411, 80A, Bat-
tery).
aRemove:
-the front right-hand wheel (see Wheel: Removal -
Refitting) (MR 411, 35A, Wheels and tyres),
-the front right-hand wheel arch liner (see Front
wheel arch liner: Removal - Refitting) (MR 412,
55A, Exterior protection).
aUndo the lower bolt on the sub-frame tie-rod.
aRemove the upper bolt from the sub-frame tie-rod.
aRemove the sub-frame tie-rod.
aRemove the accessories belt (see 11A, Top and
front of engine, Accessories belt: Removal - Re-
fitting, page 11A-3) . Tightening torquesm
alter nator bolts25 Nm
sub-frame tie-rod lower
bolt62 Nm
sub-frame tie-rod upper
bolt21 Nm

16A-3
STARTING - CHARGING
Alternator: Removal - Refitting
D4F or D7F, and STANDARD HEATING
16A
aPress in the rings (6) using pliers or a vice to make
the fitting operation easier.
II - REFITTING OPERATION FOR PART
CONCERNED
aRefit:
-the alternator,
-the alternator bolts.
aTorque tighten the alternator bolts (25 Nm).
aRefit:
-the power lead on the alternator,
-the power lead nut on the alternator.
aConnect the alternator excitation lead connector.
III - FINAL OPERATION
aConnect the fuel pipe to the injector rail.
aRefit:
-the dipstick,
-the filler neck,
-the filler neck bolt.
aAlways replace the accessories belt.aRefit the new accessories belt (see 11A, Top and
front of engine, Accessories belt: Removal - Re-
fitting, page 11A-3) .
aFit the sub-frame tie-rod.
aRefit the upper bolt on the sub-frame tie-rod.
aTorque tighten:
-the sub-frame tie-rod lower bolt (62 Nm),
-the sub-frame tie-rod upper bolt (21 Nm).
aRefit:
-the front right-hand wheel arch liner (see Front
wheel arch liner: Removal - Refitting) (MR 412,
55A, Exterior protection),
-the front right-hand wheel (see Wheel: Removal -
Refitting) (MR 411, 35A, Wheels and tyres).
aConnect the battery (see ) (MR 411, 80A, Battery).
18987
D4F, and 780

16A-4
STARTING - CHARGING
Alternator: Removal - Refitting
D4F or D7F, and AIR CONDITIONING
16A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (02A, Lifting equipment).
aDisconnect the battery (see Battery: Removal - Re-
fitting) (80A, Battery).
aRemove:
-the front right-hand wheel (see Wheel: Removal -
Refitting) (35A, Wheels and tyres),
-the front right-hand wheel arch liner (see Front
wheel arch liner: Removal - Refitting) (55A, Ex-
terior protection),
-the accessories belt (see 11A, Top and front of
engine, Accessories belt: Removal - Refitting,
page 11A-3) .
aRemove the air filter unit (see 12A, Fuel mixture,
Air filter unit: Removal - Refitting, page 12A-13) .
aRemove the inlet distributor (see 12A, Fuel mixture,
Inlet distributor: Removal - Refitting, page 12A-
29) .II - OPERATION FOR REMOVAL OF PART
CONCERNED
aDisconnect the alternator connector.
aRemove the alternator positive terminal nut.
aRemove:
-the alternator bolts,
-the alternator. Tightening torquesm
alter nator bolts25 N.m
D4F
120519