2009 RENAULT TWINGO ABS

19A-55
COOLING
Engine cooling fan assembly: Removal - Refitting
D4F, and 780 or 782
19A
aRemove the tabs (3) .
aRemove the engine cooling fan assembly.
REFITTING
I - REFITTING PREPARATIONS OPERATION
Rebuilding the cooling radiator
aRefit the engine cooling fan assembly.
aClip on the engine cooling fan assembly tabs.
II - REFITTING OPERATION FOR PART
CONCERNED
aRefit:
-the « radiator / engine cooling fan assembly » unit,
-the radiator mounting cross member (see Radiator
mounting cross member: Removal - Refitting)
(MR 412, 41A, Front lower structure).
III - FINAL OPERATION
aConnect the engine cooling fan assembly connec-
tors.
aClip:
-the wiring harness to the engine cooling fan as-
sembly,
-the bottom hose to the engine cooling fan assem-
bly.aConnect:
-the radiator degassing hose,
-the radiator top hose.
aUsing the (Mot. 1448), fit:
-the radiator degassing hose clip,
-the radiator top hose clip.
aRefit:
-the air filter box air inlet pipe,
-the air filter unit air inlet pipe bolt on the cross
member.
aConnect the air filter unit air inlet pipe to the air filter
unit cover.
aRefit:
-the front bumper (see Front bumper: Removal -
Refitting) (MR 412, 55A, Exterior protection),
-the front wheel arch liners (see Front wheel arch
liner: Removal - Refitting) (MR 412, 55A, Exterior
protection),
-the front wheels (see Wheel: Removal - Refitting)
(MR 411, 35A, Wheels and tyres).
aConnect the battery (see ) (MR 411, 80A, Battery).
aFill and bleed the cooling system (see 19A, Cool-
ing, Cooling system: Draining - Refilling, page
19A-9) .
121770

19C-7
TANK
Fuel tank: Removal - Refitting
D4F or D7F or K4M or K9K
19C
aRemove:
-the clip (8) between the catalytic converter and the
expansion chamber,
-the exhaust pipe rubber mounting bush bolt (9) ,
-the heat shield clips under the tank,
-the heat shield under the tank.aOpen the ABS sensor connector protective unit (10)
.
aDisconnect the ABS sensor connectors (11) .
aDetach the anti-lock braking connectors protective
housing from the tank. K4M
131773
119438
119437

19C-8
TANK
Fuel tank: Removal - Refitting
D4F or D7F or K4M or K9K
19C
aRemove the bolts (12) from the rear brake hose
mounting.
aDetach the brake pipes from the body (13) .II - OPERATION FOR REMOVAL OF PART
CONCERNED
aRemove the fuel vapour absorber (see 14A, Anti-
pollution, Fuel vapour absorber: Removal - Refit-
ting, page 14A-4) .
aDisconnect the anti-splashback pipe (14) .
aRemove the clip (15) from the filling pipe.
aDisconnect the filling pipe.
119686
119688
D4F or D7F or K4M
121722
WARNING
To prevent impur ities from entering the circuit,
plugs must be fitted to the openings of all the fuel
circuit components exposed to the open air.

19C-9
TANK
Fuel tank: Removal - Refitting
D4F or D7F or K4M or K9K
19C
aDetach the brake cables (16) on the tank.
aFit a component support under the fuel tank.
aRemove:
-the tank bolts (17) ,
-the tank.
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
aRefit the tank.
aTorque tighten the tank bolts (21 N.m).
aAttach the brake cables to the tank.
aConnect the filler pipe.
aRefit the filler pipe clip on the neck.
aConnect the anti-splashback pipe.aRefit the fuel vapour absorber (see 14A, Antipollu-
tion, Fuel vapour absorber: Removal - Refitting,
page 14A-4) .
II - FINAL OPERATION.
aConnect the brake pipes to the body.
aRefit the rear brake hose mounting bolts.
aClip the protective housing of the ABS connectors
onto the tank.
aConnect the ABS sensor connectors.
aClose the anti-lock braking system sensor connector
protective housing.
aRefit:
-the heat shield under the tank.
-the heat shield clips under the tank,
-the exhaust system rubber mounting bush bolt,
-the clip between the catalytic converter and the ex-
pansion chamber,
aClip the calliper parking brake cables onto the tank
and the callipers.
119652
119685
D4F or D7F or K4M
K4M