2009 RENAULT TWINGO wiring

19A-18
COOLING
Cooling radiator: Removal - Refitting
D4F or D7F, and STANDARD HEATING
19A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (MR 411, 02A, Lifting equip-
ment).
aDisconnect the battery (see ) (MR 411, 80A, Bat-
tery).
aRemove:
-the front wheels (see Wheel: Removal - Refitting)
(MR 411, 35A, Wheels and tyres),
-the front wheel arch liners (see Front wheel arch
liner: Removal - Refitting) (MR 412, 55A, Exterior
protection),
-the front bumper (see Front bumper: Removal -
Refitting) (MR 412, 55A, Exterior protection).
aDisconnect the air filter unit air inlet pipe (1) from the
air filter unit cover.
aRemove:
-the air filter unit air inlet pipe bolt from the cross
member (2) ,-the air filter unit air inlet pipe.
aDrain the cooling system (see 19A, Cooling, Cool-
ing system: Draining - Refilling, page 19A-9) .
aRemove using the (Mot. 1448) :
-the radiator top hose clip,
-the radiator degassing hose clip.
aDisconnect:
-the radiator top hose,
-the radiator degassing hose.
aUnclip:
-the lower hose from the engine cooling fan assem-
bly,
-the wiring harness from the engine cooling fan as-
sembly.
aDisconnect the engine cooling fan assembly con-
nectors.
II - REMOVAL OPERATION FOR PART
CONCERNED
aRemove:
-the radiator mounting cross member (see Radiator
mounting cross member: Removal - Refitting)
(MR 412, 41A, Front lower structure),
-the « radiator / engine cooling fan assembly » unit.
Stripping the cooling radiator
aRemove the radiator plastic deflectors.
aUnclip the engine cooling fan assembly.
REFITTING
I - REFITTING PREPARATIONS OPERATION
Rebuilding the cooling radiator
aClip the engine cooling fan assembly in place.
aRefit the radiator plastic deflectors.
II - REFITTING OPERATION FOR PART
CONCERNED
aRefit:
-the « radiator / engine cooling fan assembly » unit, Special tooling required
Mot. 1448Remote operation pliers for
hose clips .
D4F, and 780
122833

19A-19
COOLING
Cooling radiator: Removal - Refitting
D4F or D7F, and STANDARD HEATING
19A
-the radiator mounting cross member (see Radiator
mounting cross member: Removal - Refitting)
(MR 412, 41A, Front lower structure).
III - FINAL OPERATION
aConnect the engine cooling fan assembly connec-
tors.
aClip:
-the wiring harness to the engine cooling fan as-
sembly,
-the bottom hose to the engine cooling fan assem-
bly.
aConnect:
-the radiator degassing hose,
-the radiator top hose.
aUsing the (Mot. 1448), fit:
-the radiator degassing hose clip,
-the radiator top hose clip.
aRefit:
-the air filter box air inlet pipe,
-the air filter unit air inlet pipe bolt on the cross
member.
aConnect the air filter unit air inlet pipe to the air filter
unit cover.
aRefit:
-the front bumper (see Front bumper: Removal -
Refitting) (MR 412, 55A, Exterior protection),
-the front wheel arch liners (see Front wheel arch
liner: Removal - Refitting) (MR 412, 55A, Exterior
protection),
-the front wheels (see Wheel: Removal - Refitting)
(MR 411, 35A, Wheels and tyres).
aConnect the battery (see ) (MR 411, 80A, Battery).
aFill and bleed the cooling system (see 19A, Cool-
ing, Cooling system: Draining - Refilling, page
19A-9) . D4F, and 780

19A-21
COOLING
Cooling radiator: Removal - Refitting
K4M
19A
aDisconnect the connector (1) from the air condition-
ing pressure sensor.
aRemove:
-the condenser protector (2) ,
-the « dehydrator reservoir - expansion valve » con-
necting pipe bolt (3) ,
-the « compressor - condenser » connecting pipe
bolt (4) .
aDisconnect:
-the « dehydrator reservoir - expansion valve » con-
necting pipe,
-the « compressor - condenser » connecting pipe.
aFit protective plugs onto the air conditioning pipe
unions.
aRemove using the (Mot. 1448) :
-the cooling radiator top hose clip,
-the cooling radiator degassing hose clip.
aDisconnect:
-the cooling radiator top hose,
-the cooling radiator degassing hose.aDisconnect:
-the engine cooling fan assembly resistor connector
(5) ,
-the engine cooling fan assembly connector (6) .
aUnclip:
-the engine cooling fan assembly wiring at (7) ,
-the cooling radiator top and bottom hose from the
engine cooling fan assembly.
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aAttach the « radiator - condenser- fan » assembly to
the upper cross member using a safety strap(s).
aRemove:
-the radiator mounting cross member (see Radiator
mounting cross member: Removal - Refitting)
(41A, Front lower structure),
-the « radiator - condenser- fan » assembly by loos-
ening the safety strap(s).
132335132336

19A-22
COOLING
Cooling radiator: Removal - Refitting
K4M
19A
On the workbench
aUnclip:
-the engine cooling fan assembly from the radiator
at (8) by pushing it upwards to detach the brackets
holding it,
-the cooling radiator protector (9) .
REFITTING
I - REFITTING PREPARATION OPERATION
aAlways replace the seals on the air conditioning
pipes.
On the workbench
aClip:
-the radiator protector,
-the engine cooling fan assembly to the cooling ra-
diator.
II - REFITTING OPERATION FOR PART
CONCERNED
aRefit:
-the « radiator - condenser - fan » assembly,
-the radiator mounting cross member (see Radiator
mounting cross member: Removal - Refitting)
(41A, Front lower structure).III - FINAL OPERATION.
aClip:
-the cooling radiator top and bottom hose on the en-
gine cooling fan assembly,
-the engine cooling fan assembly wiring.
aConnect:
-the engine cooling fan assembly connector,
-the engine cooling fan assembly resistor connec-
tor.
aConnect:
-the cooling radiator top hose,
-the cooling radiator degassing hose.
aUsing the (Mot. 1448), fit:
-the cooling radiator top hose clip,
-the cooling radiator degassing hose clip.
aRefit the new seals on the air conditioning pipes.
aConnect:
-the « dehydrator reservoir - expansion valve » con-
necting pipe,
-the « compressor - condenser » connecting pipe.
aTighten to torque:
-the bolt of the dehydrator reservoir -
« expansion valve connecting pipe » (8 N.m),
-the compressor - condenser « connecting pipe
bolt » (8 N.m).
aTorque tighten the air conditioning connecting
pipe bolts (8 N.m).
aRefit the condenser protector.
aConnect the air conditioning pressure sensor con-
nector.
aRefit:
-the front bumper (see Front bumper: Removal -
Refitting) (55A, Exterior protection),
-the front wheel arch liners (see Front wheel arch
liner: Removal - Refitting) (55A, Exterior protec-
tion),
-the front wheels (see Wheel: Removal - Refitting)
(35A, Wheels and tyres).
aConnect the battery (see Battery: Removal - Refit-
ting) (80A, Battery).
132336

19A-49
COOLING
Water chamber: Removal - Refitting
K4M
19A
aUsing the (Mot. 1448) or (Mot. 1202-01) or (Mot.
1202-02) remove:
-the cooling radiator top hose clip on the water
chamber,
-the heater matrix hose clip (1) on the water cham-
ber.
aDisconnect from the water chamber:
-the cooling radiator top hose,
-the heater matrix hose.
aRemove:
-the bolt (2) from the heater matrix hose bracket,
-the heater matrix hose bracket,
-the bolts (3) of the engine wiring channel,
-the coolant temperature sensor (see 19A, Cool-
ing, Coolant temperature sensor: Removal - Re-
fitting, page 19A-66) .
aMove aside the engine wiring channel.
aUnclip the wiring at (4) .II - REMOVAL OPERATION
aRemove:
-the coolant outlet unit bolts,
-the water chamber,
-the water chamber seal.
REFITTING
I - REFITTING PREPARATION OPERATION
aparts always to be replaced: Cylinder head cool-
ant outlet unit seal.
aUse SURFACE CLEANER (see Vehicle: Parts
and consumables for the repair) (04B, Consuma-
bles - Products) to clean and degrease:
-the cylinder head joint face,
-the coolant outlet unit housing if it is being reused.
132444
128456
WARNING
The joint faces must be clean, dr y and free from
grease (avoid finger marks).

19A-50
COOLING
Water chamber: Removal - Refitting
K4M
19A
II - REFITTING OPERATION
aRefit the coolant outlet unit with a new seal.
aPretighten in order and to torque the water cham-
ber bolts (initial torque) (4 N.m).
aTorque tighten in order the water chamber bolts
(12 N.m).
III - FINAL OPERATION
aClip the wiring onto the water chamber.
aFit the engine wiring channel.
aRefit:
-the coolant temperature sensor (see 19A, Cool-
ing, Coolant temperature sensor: Removal - Re-
fitting, page 19A-66) ,
-the heater matrix hose bracket.
aTorque tighten the heater matrix hose bracket bolt
(10 N.m).
aConnect to the coolant outlet unit:
-the heater matrix hose,
-the cooling radiator top hose.
aUsing the (Mot. 1448) or (Mot. 1202-01) or (Mot.
1202-02) fit:
-the heater matrix hose clip,
-the cooling radiator top hose clip.
aRefit the air filter unit (see 12A, Fuel mixture, Air fil-
ter unit: Removal - Refitting, page 12A-13) .aFill and bleed the cooling system (see 19A, Cool-
ing, Cooling system: Draining - Refilling, page
19A-9) .
aRefit the engine undertray.
128456

19A-51
COOLING
Engine cooling fan assembly: Removal - Refitting
C44, and K9K
19A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift ( (see Vehicle:
Towing and lifting) )
aDisconnect the battery ( (see Battery: Removal -
Refitting) ).
aRemove:
-the engine undertray bolts,
-the engine undertray,
-the front bumper ( (see Front bumper: Removal -
Refitting) ),
-the left-hand and right-hand headlights (see Halo-
gen headlight: Removal - Refitting) .
aRemove:
-the cooling radiator retaining lug bolt,
-the expansion bottle bolt onto the front upper cross
member,
-the air filter inlet air pipe bolt on the front upper
cross member.
aUnclip and then remove from the front upper cross
member:
-the air filter inlet air pipe,
-the expansion bottle.
aRemove the bonnet lock nuts.
aRemove the « cable - bonnet catch » assembly.
aRemove the front upper cross member ( (see Front
upper cross member: Removal - Refitting) )
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aDisconnect the electrical connectors on the engine
cooling fan assembly.
aUnclip:
-the engine cooling fan assembly wiring,
-the coolant hose at the bottom of the engine cool-
ing fan assembly.aPress on the engine cooling fan assembly locking
tabs (1) on the cooling radiator.
Note:
Do not unclip the bonnet release cable to avoid
damaging the cable clip on the lock.
AIR CONDITIONING
120324
Note:
Be careful not to press too hard on the tabs to
avoid breaking them.

19A-52
COOLING
Engine cooling fan assembly: Removal - Refitting
C44, and K9K
19A
aPress on the engine cooling fan assembly locking
tabs (2) on the cooling radiator.
aWithdraw the engine cooling fan assembly from the
cooling radiator from above, while pressing on the
locking tabs.
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
aFit the engine cooling fan assembly to the cooling ra-
diator.
aClip the engine cooling fan assembly to the cooling
radiator.
aConnect the electrical connectors to the engine cool-
ing fan assembly.aClip:
-the engine cooling fan assembly wiring in place,
-the coolant hose at the bottom of the engine cool-
ing fan assembly.
II - FINAL OPERATION
aRefitting the front upper cross member (see MR 412
Bodywork, 42A, Upper front structure, Cross
member: Removal - Refitting).
aFit the « cable - bonnet catch » assembly.
aRefit the bonnet catch nuts.
aClip and move away from the front upper cross
member:
-the expansion bottle,
-the air filter inlet air pipe.
aRefit:
-the air filter inlet air pipe bolt onto the front upper
cross member,
-the expansion bottle bolt onto the front upper cross
member,
-the cooling radiator retaining lug bolt.
aTighten on the front upper cross member:
-the air filter inlet air pipe bolt onto the front upper
cross member,
-the expansion bottle bolt onto the front upper cross
member,
-the cooling radiator retaining lug bolt.
aRefit:
-the left-hand and right-hand headlights (see 80B,
Headlights, Halogen headlights: Removal - Re-
fitting),
-the front bumper ( (see Front bumper: Removal -
Refitting) ),
-the engine undertray,
-the engine undertray bolts.
aTighten the engine undertray bolts until contact is
made.
aConnect the battery ( (see Battery: Removal - Re-
fitting) ). STANDARD HEATING
120325
Note:
Be careful not to press too hard on the tabs to
avoid breaking them.
Note:
Check that the tabs lock the engine cooling fan
assembly on the cooling radiator correctly.