2009 RENAULT TWINGO display

87B-80
MR-413-X44-87B000$480.mif
V5
UCH
Vdiag No.: 44PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check87B
SUB-FUNCTION: WIPING CONTROL
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
FunctionParameter or Status
Checked or ActionDisplay and notes Fault finding
Wiper controlET077:Wiper stalk positionINACTIVE
INTERMITTENT
LOW-SPEED
HIGH SPEEDIn the event of a fault, apply the
interpretation of status ET077.
ET096:Wiper stalk
intermittent speed
ring position1
2
3
4
5In the event of a fault, apply the
interpretation of status ET096.
ET114:Windscreen wiper
request by rain
sensorABSENT
LOW-SPEED
HIGH SPEEDIn the event of a fault, apply the
interpretation of status ET114.
Windscreen wiper
park positionET078:Windscreen washer
requestACTIVE
INACTIVEIn the event of a fault, apply the
interpretation of status ET078.
ET027:Windscreen wiper
park positionACTIVE
INACTIVEIn the event of a fault, apply the
interpretation of status ET027.
Rear screen wiper
park positionET079:Rear screen washer
requestACTIVE
INACTIVEIn the event of a fault, apply the
interpretation of status ET079.
ET097:Rear screen wiper
park positionACTIVE
INACTIVEIn the event of a fault, apply the
interpretation of fault ET097.
ET080:Windscreen
rear screen wiperACTIVE
INACTIVEIn the event of a fault, apply the
interpretation of status ET080.
Reverse gearET109:Reverse gear
engagedYES
NOIn the event of a fault, apply the
interpretation of status ET109.

87B-81
MR-413-X44-87B000$480.mif
V5
UCH
Vdiag No.: 44PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check87B
SUB-FUNCTION: WIPING POWER
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
FunctionParameter or Status
Checked or ActionDisplay and
NotesFault finding
Rear screen
wiperAC007:Rear screen wiperThis command is used to
operate the rear screen
wiper.In the event of a fault, apply the
procedure for dealing with
command AC007.
Wiper speedAC058:Intermittent wiper
operationThis command is used to
operate the intermittent
windscreen wiper action.In the event of a fault, apply the
procedure for dealing with
command AC058.
AC056:Low-speed wiperThis command is used to
operate the windscreen
wipers at low speed.In the event of a fault, apply the
procedure for dealing with
command AC056.
AC057:High-speed wiperThis command is used to
operate the windscreen
wipers at high speed.In the event of a fault, apply the
procedure for dealing with
command AC057.

87B-82
MR-413-X44-87B000$480.mif
V5
UCH
Vdiag No.: 44PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check87B
SUB-FUNCTION: BATTERY
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
FunctionParameter or Status
Checked or ActionDisplay and notes Fault finding
Battery voltagePR001:Battery voltage9 V < X < 16 VIn the event of a fault, run fault
finding on the charging circuit
(see 80A, Battery).
PR074:Battery setpoint
voltageIndicates the battery
setpoint in V.In the event of a fault, apply the
interpretation of parameter
PR074.
PR076:Battery voltage after
restIndicates the battery
voltage after rest in V.In the event of a fault, apply the
interpretation of parameter
PR076.
Alternator
operationET142:Engine operating
phaseSTOPPED
STARTING
RUNNING
STALLEDIn the event of a fault, apply the
interpretation of status ET142.

87B-83
MR-413-X44-87B000$480.mif
V5
UCH
Vdiag No.: 44PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check87B
SUB-FUNCTION: ALTERNATOR
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
FunctionParameter or Status
Checked or ActionDisplay and notes Fault finding
Battery voltagePR073:Alternator charge
signalIndicates the
alternator charge in V.In the event of a fault, apply the
interpretation of parameter PR073.
Alternator
setpointPR075:Alternator setpoint
voltage
Indicates the alternator
setpoint in V.In the event of a fault, apply the
interpretation of parameter PR075.
Battery voltagePR001:Battery voltage9 V < X < 16 VIn the event of a fault, run fault finding
on the charging circuit (see, 80A
Battery), run fault finding on the
multiplex network (see 88B,
Multiplex) and run fault finding on the
injection (see 13B, Diesel injection
or 17B, Petrol injection).
EnginePR024:Engine coolant
temperature˚C
PR025:Engine speedrpmIn the event of a fault, run fault finding
on the multiplex network (see 88B,
Multiplex) and run fault finding on the
injection (see 13B, Diesel injection
or 17B, Petrol injection).
ET142:Engine operating
phaseSTOPPED
STARTING
RUNNING
STALLEDIn the event of a fault, apply the
interpretation of status ET142.
AlternatorAC130:Alternator regulationIndicates the
regulation of the
alternator in volts.In the event of a fault, run fault finding
on the charging circuit (see 80A,
Battery).

87B -104
MR-413-X44-87B000$576.mif
V5
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
UCH
Vdiag No.: 44
87B
Windscreen wiper fault:ET077
WIPER STALK POSITION
NOTESNo faults should be present or stored.
Check the following configurations:
–Check that LC094 "Wiper intermittent speed ring" displays "With". If not, carry
out CF191 "Wiper intermittent speed ring".
–Check that LC096 "Automatic wiper function" displays "With". If not, carry out
CF194 "Automatic wiper function".
SPECIFICATIONSINTERMITTENT
LOW SPEED
HIGH SPEED
Check the condition and connection of the 3-track windscreen wiper motor connector (component code 212)
(broken, bent, oxidised tabs).
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
Check that fuse F2 (15 A) is sound and correctly fitted to the passenger compartment fuse and relay box
(component code 1016).
Replace the fuse if necessary.
Check the condition and connection of the UCH 40-track connector PE1 (component code 645) (tabs bent,
oxidised or broken).
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
Check the insulation, continuity and the absence of interference resistance on the following connections:
Combined wiper-washer check:
●Connection code AP71 between components 145 and 1016.
●Connection code 14E (windscreen wiper timed control) between components 645 and 145.
●Connection code 14G (low speed windscreen wiper control) between components 645 and 145.
●Connection code 14H (high speed windscreen wiper control) between components 645 and 145.
●Connection code 36E (rear screen wiper timed control) between components 645 and 145.
●Connection code MAN or MAN between component 145 and the earth MAN (left-hand drive) or MAM
(right-hand drive).
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the problem persists, replace the wiper stalk (component code 145). (See MR 411 mechanical systems 84A,
Controls - Signals, Wiper switch: Removal - Refitting).
AFTER REPAIRRepeat the conformity check from the start.
Carry out fault finding on the system.
UCH_V44_ET077

87B -106
MR-413-X44-87B000$576.mif
V5
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
UCH
Vdiag No.: 44
87B
ET080
REAR SCREEN WIPER REQUEST
NOTESNo faults should be present or stored.
Check the following configuration:
Check that LC096 "Automatic wiper function" displays "With". If not, carry out
CF194 "Automatic wiper function".
SPECIFICATIONSACTIVE
INACTIVE
Check that fuse F36 (15 A) is sound and correctly fitted to the passenger compartment fuse and relay box
(component code 1016).
Replace the fuse if necessary.
Check the condition and connection of the 3-track rear screen wiper motor connector (component code 211)
(broken, bent, oxidised tabs).
Activate the rear screen wiper, check for + 12 V on connection 36A of the rear screen wiper
motor connector (component code 211).
Check that the earth on connection MYH of the rear screen wiper motor connector (component code 211) is in
perfect condition.
Check the condition and connection of the UCH 40-track connector PE1 (component code 645) (tabs bent,
oxidised or broken).
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
AFTER REPAIRRepeat the conformity check from the start.
Carry out fault finding on the system.
UCH_V44_ET080

87B -108
MR-413-X44-87B000$576.mif
V5
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
UCH
Vdiag No.: 44
87B
ET081
LIGHTING STALK POSITION
NOTESNo faults should be present or stored.
Check the following configurations:
–Check that LC008 Daytime running lights is With. Otherwise carry out CF014
"Daytime running lights".
–Check that LC015 Front fog lights is With. Otherwise run CF021 Front fog
lights.
–Check that LC025 "See-me-home lighting" is "With". Otherwise carry out
CF032 "See-me-home lighting".
–Check that LC044 "Rain/light sensor" displays "Present". If not, carry out
CF035 "Rain/light sensor".
–Check that LC095 "Automatic headlight function", displays "With". If not, carry
out CF193 "Automatic headlight function".
SPECIFICATIONSHAZARD LIGHTS
SIDE
DIPPED
MAIN BEAM HEADLIGHTS
Check that fuses F13 (30 A), F15 (5 A) (without automatic headlighting) or F15 (15A) (with automatic
headlighting) is sound and correctly fitted in the passenger compartment fuse and relay box
(component code 1016).
Check the condition and connection of the monolever connector (component code 209) and the UCH 40-track
connector PE2 (component code 645) (tabs bent, broken or oxidised).
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
AFTER REPAIRRepeat the conformity check from the start.
Carry out fault finding on the system.
UCH_V44_ET081

87B -111
MR-413-X44-87B000$576.mif
V5
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
UCH
Vdiag No.: 44
87B
With automatic headlighting:ET082
REAR FOG LIGHTS REQUEST
NOTESNo faults should be present or stored.
Note:
The signal can only be interpreted if the function is managed by the UCH
(vehicle equipped with one-touch fog light control)
Check the following configurations:
Check that LC008 Daytime running lights is With. Otherwise carry out CF014
"Daytime running lights".
–Check that LC015 Front fog lights is With. Otherwise run CF021 Front fog
lights.
–Check that LC025 "See-me-home lighting" is "With". Otherwise carry out
CF032 "See-me-home lighting".
–Check that LC044 "Rain/light sensor" displays "Present". If not, carry out
CF035 "Rain/light sensor".
–Check that LC095 "Automatic headlight function", displays "With". If not, carry
out CF193 "Automatic headlight function".
SPECIFICATIONSPRESENT
ABSENT
Check the presence and condition of fuses F15 (5 A), F20 (15 A), F25 (5 A), F39 (10 A) on the passenger
compartment fuse and relay box (component code 1016).
Replace the fuse if necessary.
Check the correct positioning and condition of the bulb concerned. Replace the light if necessary.
Check the condition and connection of the light concerned (bent, oxidised, broken tabs).
Check the condition and connection of the UCH PE2 connector (component code 645) (tabs bent, oxidised or
broken).
Check the condition and connection of the horn and lights switch connector (component code 209) (tabs bent,
oxidised, broken).
Check for + 12 V (when rear fog lights are requested) on connection 9P of components 172 and 173.
Check for earth on connection MF of component 172 and connection MG on component 173.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
AFTER REPAIRRepeat the conformity check from the start.
Carry out fault finding on the system.
UCH_V44_ET082