2009 RENAULT TWINGO immobiliser

87B-70
MR-413-X44-87B000$480.mif
V5
UCH
Vdiag No.: 44PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check87B
SUB-FUNCTION: PROTECTION (CONTINUED)
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
FunctionParameter or Status
Checked or ActionDisplay and
NotesFault finding
KeyET045:Radio frequency
signal receivedYES = When the UCH receives
a radiofrequency signal.
NO = When the UCH does not
receive a Radiofrequency
signal.In the event of a fault, refer to
the interpretation of status
ET045.
ET193:Radiofrequency
signal from a key
allocated to the
vehiclePRESENT =
Reception of a signal
Radiofrequency signal from a
key allocated to the vehicle.
ABSENT =
No reception of signal
Radiofrequency or signal
Radiofrequency signal from a
key not allocated to the vehicleIn the event of a fault, refer to
the interpretation of status
ET193.
ET240:Key frequency (in
MHz)433
NONEIf NONE, refer to the
interpretation of status
ET240.
PR056:Number of keys
allocatedX ≤ 4 key(s)In the event of a fault, refer to
the interpretation of fault
PR056.
InjectionET229:Injection immobiliser
codePROGRAMMED
NOT PROGRAMMED
UNDETERMINEDIn the event of a fault, consult
the interpretation of status
ET229.
ET250:InjectionNOT PROTECTED
PROTECTEDIn the event of a fault, refer to
the interpretation of status
ET250.
(See 17B, Petrol Injection,
Conformity check,
Protection) or (see 13B,
Diesel Injection, Conformity
check, Protection).
Starter actuatorET239:Ignition switch
positionINACTIVE
+ ACCESSORIES
+ after ignition feed.
+ START FEEDIn the event of a fault, refer to
the interpretation of status
ET239.

87B-84
MR-413-X44-87B000$528.mif
V5
87B
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Status summary table
*CPE: Electric central door locking
*RF: radio frequencyTool status Diagnostic tool title
ET008Blank UCH
ET015Passenger compartment blower
ET027Windscreen wiper park position
ET028Heated rear screen button
ET029Air conditioning button
ET030Air conditioning request 2
ET044CPE* button
ET045RF* signal. received
ET046Engine immobiliser
ET047Brake pedal position
ET061Open tailgate request
ET077Wiper stalk position
ET078Windscreen washer request
ET079Rear screen washer request
ET080Rear screen wiper request
ET081Lighting switch position
ET082Rear fog lights request
ET083Left-hand indicator request
MR-413-X44-87B000$528.mif
UCH
Vdiag No.: 44

87B-85
MR-413-X44-87B000$528.mif
V5
UCH
Vdiag No.: 44PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Status summary table87B
*SR: Sunroof.
*RF: radio frequencyTool status Diagnostic tool title
ET084Right-hand indicator request
ET085Hazard warning lights button
ET087One-touch window/SR* authorisation
ET096Wiper intermittent speed ring position
ET097Rear screen wiper park position
ET109Reverse gear engaged
ET111Front fog lights request
ET114Wiping request via rain sensor
ET115Request to switch on lights by light sensor
ET142Engine operating phase
ET181Key allocated to the vehicle
ET185Key code received
ET186Short press on door closing button
ET189Long press on door opening button
ET193RF* signal from a key allocated to the vehicle
ET229Injection immobiliser code
ET239Ignition switch position
ET240Key frequency (in Hz)
ET250Injection
ET463Door(s) or tailgate

87B-99
MR-413-X44-87B000$576.mif
V5
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
UCH
Vdiag No.: 44
87B
ET046
ENGINE IMMOBILISER
NOTESNo faults should be present or stored.
Apply the checks only if, the status remains ACTIVE after the ignition is switched off
and back on again under the following conditions.
SPECIFICATIONSACTIVE
INACTIVE
Check sure that ET239 Ignition switch position is + after ignition feed. Otherwise, refer to the interpretation of
this status.
Check that ET185 Key code received is YES.
Otherwise, refer to the interpretation of this status.
Check that ET181 Key allocated to vehicle is YES.
Otherwise, refer to the interpretation of this status.
Check that ET008 UCH blank is NO.
Otherwise, refer to the interpretation of this status.
Check that ET229 Injection immobiliser code is PROGRAMMED.
Otherwise, refer to the interpretation of this status.
Check that ET250 Injection is NOT PROTECTED.
Otherwise, refer to the interpretation of this status.
Carry out fault finding on the multiplex network (see 88B, Multiplexing).
If none of the computers on the vehicle has a malfunction and the statuses named in the notes are working
properly, contact Techline.
AFTER REPAIRRepeat the conformity check from the start.
Carry out fault finding on the system.
UCH_V44_ET046

87B -132
MR-413-X44-87B000$624.mif
V5
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
UCH
Vdiag No.: 44
87B
ET185
KEY CODE RECEIVED
NOTESThere must be no present or stored faults.
Apply the checks only if the status is NO with the ignition on.
SPECIFICATIONSYES
NO
Check that there are no powerful electromagnetic wave sources (CB (Citizen Band), mobile phone in close
proximity to the transponder ring).
Switch the ignition off and then on again.
Check that fuse F8 (15 A) is sound and correctly fitted in the passenger compartment fuse and relay box.
Replace the fuse if necessary.
Try the vehicle's second key.
If the status changes to YES, replace the first key and program the keys using command SC015 Key allocation.
This status tells you whether the UCH has received the immobiliser code from the key.
If the status remains NO, check the connection between the transponder ring (component code 1618) and the
UCH (component code 645).
Check the + 12 V feed on connection AP43 of component 1618.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check that the earth on track 2 of the transponder ring is in perfect condition.
Check the insulation, the continuity and the absence of interference resistance on the following
connections:
●Connection code AP43 between components 1016 and 1618.
●Connection code 80X between components 645 and 1618.
●Connection code 80Y between components 645 and 1618.
●Connection code NAM between component 1618 and earth.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact the Techline.
AFTER REPAIRRepeat the conformity check from the start.
Carry out fault finding on the system.
UCH_V44_ET185

87B -135
MR-413-X44-87B000$624.mif
V5
UCH
Vdiag No.: 44PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses87B
* Powerlatch: Time required for injection computer supply after + 12 V after ignition feed cut-off. ET229
INJECTION IMMOBILISER CODE
NOTESThere must be no present or stored faults.
Only apply the checks if the status is NOT PROGRAMMED or NOT DETERMINED
after activating the + After ignition feed for 20 seconds; switch off the ignition, wait for
the end of Powerlatch (20 minutes maximum), and then switch on the ignition again.
SPECIFICATIONSUNDETERMINED
NOT PROGRAMMED
PROGRAMMED
STATUS
NOT
PROGRAMMED
Run command SC017 Program injection immobiliser code.
STATUS
UNDETERMINEDSwitch the ignition off and then on again.
First check whether statuses ET046 Immobliser, ET181 Key allocated to the vehicle
and ET239 Position of the ignition switch are correct.
Carry out a multiplex network test (see 88B, Multiplexing).
Carry out fault finding on the injection system (see 13B, Diesel injection or 17B,
Petrol injection).
Check the condition of the injection computer connectors.
Check that the + 12 V supply and injection computer earth (component code 120) are
in order.
If the fault is still present, contact the Techline.
AFTER REPAIRRepeat the conformity check from the start.
Carry out fault finding on the system.
UCH_V44_ET229

87B -136
MR-413-X44-87B000$624.mif
V5
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
UCH
Vdiag No.: 44
87B
ET239
IGNITION SWITCH POSITION
NOTESThere must be no present or stored faults.
SPECIFICATIONS+ APC
+ START
+ ACCESSORIES FEED
Check the correct position and condition of fuses F2 (60A) in the engine fuse and relay box (component code
597) and F8 (15A) in the passenger compartment fuse and relay box (component code 1016).
Replace the fuse if necessary.
Check the condition and connection of the starter switch connector (component code 104) (tabs bent, broken,
oxidised).
Check the condition and connection of the PE1 connector of the UCH, (component code 645) (tabs bent,
oxidised, broken).
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
Check for +12 V on connection AP29 of component 232.
Check the insulation, continuity and the absence of interference resistance on the connections between the
UCH (component code 645) and the ignition switch (component 104):
●Connection code A between components 104 and 1016.
●Connection code BP12 between components 104 and 597.
●Connection code AP43 between components 1016 and 645.
●Connection code D between components 104 and 232.
●Connection code 1B between components 232 and 645.
●Connection code AP29 between components 1016 and 232.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the connections are in order, replace the ignition switch (component code 104).
(See MR 411 Mechanical 82A, Immobiliser, Ignition switch: Removal - Refitting).
If the fault is still present, contact the Techline.
AFTER REPAIRRepeat the conformity check from the start.
Carry out fault finding on the system.
UCH_V44_ET239

87B -138
MR-413-X44-87B000$624.mif
V5
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
UCH
Vdiag No.: 44
87B
*Powerlatch: Time required for injection computer supply after + 12 V after ignition feed cut-off to the ignition switch. ET250
INJECTION
NOTESThere must be no present or stored faults.
Switch on the + after ignition feed for 20 seconds, switch off the ignition, wait until the
end of Powerlatch* (20 minutes maximum), then switch on the ignition again.
Check that the immobiliser warning light remains lit.
SPECIFICATIONSNOT PROTECTED
PROTECTED
After the setpoint has been obtained, if the status remains PROTECTED, first check that statuses ET046 Engine
immobiliser, ET181 Key allocated to vehicle and ET229 Injection immobiliser code are operating correctly.
Carry out a multiplex network test (see 88B, Multiplexing).
Carry out fault finding on the injection system (see 13B, Diesel injection or 17B, Petrol injection).
If the fault is still present, contact the Techline.
AFTER REPAIRRepeat the conformity check from the start.
Carry out fault finding on the system.
UCH_V44_ET250