2009 RENAULT TWINGO Engine And Peripherals Multimedia Connection Unit Workshop Manual

86D-25
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults using command RZ001 Fault memory.
Deal with any other faults.
V1 MR-413-X44-86D000$090.mif
MULTIMEDIA CONNECTION UNIT
Fault finding – Interpretation of faults86D
BIC
Vdiag No.: 14
DF007
PRESENT
OR
STOREDCOMPUTER
1.DEF: Internal electronic fault
NOTESIf the fault is present, the multimedia function is locked and no computer (radio, radio
control satellite, etc.) operates.
If the vehicle is equipped with a Navigation computer (only on Clio III), replace the multimedia connection unit (see
MR 392, Mechanical, 83C, On-board telematics system, Multimedia network interface unit: Removal -
Refitting).
If the vehicle is not equipped with a Navigation computer, replace the display (see MR 392 (Clio III) or MR 411
(New Twingo), Mechanical, 86A, Radio, Display: Removal - Refitting).
If the fault is still present, contact your Techline.
BIC_V14_DF007

86D-26
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults using command RZ001 Fault memory.
Deal with any other faults.
V1 MR-413-X44-86D000$090.mif
MULTIMEDIA CONNECTION UNIT
Fault finding – Interpretation of faults86D
BIC
Vdiag No.: 14
DF008
PRESENT
OR
STOREDCOMPUTER
1.DEF: Internal electronic fault
NOTESIf the fault is present, the multimedia function is locked and no computer (radio, radio
control satellite, etc.) operates.
If the vehicle is equipped with a Navigation computer (only on Clio III), replace the multimedia connection unit (see
MR 392, Mechanical, 83C, On-board telematics system, Multimedia network interface unit: Removal -
Refitting).
If the vehicle is not equipped with a Navigation computer, replace the display (see MR 392 (Clio III) or MR 411
(New Twingo), Mechanical, 86A, Radio, Display: Removal - Refitting).
If the fault persists, contact your Techline.
BIC_V14_DF008

86D-27
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults using command RZ001 Fault memory.
Deal with any other faults.
V1 MR-413-X44-86D000$090.mif
MULTIMEDIA CONNECTION UNIT
Fault finding – Interpretation of faults86D
BIC
Vdiag No.: 14
DF011
PRESENT
OR
STOREDEXTERNAL TEMPERATURE SENSOR CIRCUIT
CC.0: Short circuit to earth
CC.1: Open circuit or short circuit to +12 V
NOTESConditions for applying the fault finding procedure to stored faults:
The fault is declared present after the ignition is switched off and back on.
Configure the system using CF007 Vehicle configuration followed by CF012 Lighting configuration (See
Configurations and programming).
If the fault is still present, contact the Techline.
BIC_V14_DF011

86D-28V1 MR-413-X44-86D000$100.mif
86D
BIC
Vdiag No.: 14
MAIN SCREEN
NOTESOnly carry out a conformity check after a complete check with the diagnostic tool. The
values shown in this conformity check are given as a guide.
Application conditions: Engine stopped, ignition on, and the radio switched on.
FunctionParameter or status
checked or actionDisplay
and notesFault finding
Side lightsET004:+12 V Side
lightsINACTIVE
INVALID
OFF
ONIn the event of an inconsistency,
run fault finding on the UCH (see
87B, Passenger compartment
connection unit).
BIC_V14_CCONF
MULTIMEDIA CONNECTION UNIT
Fault finding – Conformity check

86D-29V1 MR-413-X44-86D000$100.mif
MULTIMEDIA CONNECTION UNIT
Fault finding – Conformity check86D
BIC
Vdiag No.: 14
FUNCTION: MULTIMEDIA
SUB-FUNCTION: USER SELECTION
NOTESOnly carry out a conformity check after a complete check with the diagnostic tool. The
values shown in this conformity check are given as a guide.
Application conditions: Engine stopped, ignition on, and the radio switched on.
FunctionParameter or status
Checked or actionDisplay and notes Fault finding
ButtonET002:Radio on/off buttonINACTIVE
ACTIVE
This status remains
active until the ignition is
switched off.In the event of an
inconsistency, run fault
finding on the radio (see 86A,
Radio)
Battery voltagePR002:Battery voltage12 V < X < 15 VIn the event of an
inconsistency, consult the
interpretation of fault DF005
Supply.
Vehicle speedPR003:Vehicle speedIndicates the vehicle
speed in mph (km/h).In the event of an
inconsistency, run fault
finding on the ABS (see 38C,
Anti-lock braking system).
External
temperaturePR004External
temperature-40˚C < X < 60˚CIn the event of an
inconsistency, run fault
finding on the UCH (see 87B,
Passenger compartment
connection unit).
System activationAC002:On - Off ButtonUsed to simulate the On -
Off Button of the radioIn the event of an
inconsistency, consult the
interpretation of fault DF006
Activation signal and run
fault finding on the radio (see
86A, Radio).

86D-30V1 MR-413-X44-86D000$100.mif
MULTIMEDIA CONNECTION UNIT
Fault finding – Conformity check86D
BIC
Vdiag No.: 14
FUNCTION: MULTIMEDIA (CONTINUED)
SUB-FUNCTION: USER SELECTION
NOTESOnly carry out a conformity check after a complete check with the diagnostic tool. The
values shown in this conformity check are given as a guide.
Application conditions: Engine stopped, ignition on, and the radio switched on.
FunctionParameter or status
Checked or actionDisplay and notes Fault finding
ButtonET009:Repeat button
(only on Clio III)
PRESSED
RELEASEDIn the event of an
inconsistency, consult the
interpretation of status
ET009.
ET020:Mute buttonIn the event of an
inconsistency, consult the
interpretation of status
ET020.
ET011:+ buttonIn the event of an
inconsistency, consult the
interpretation of status
ET011.
ET012:- buttonIn the event of an
inconsistency, consult the
interpretation of status
ET012.
ET023:Source buttonIn the event of an
inconsistency, consult the
interpretation of status
ET023.
ET024:Mode button In the event of an
inconsistency, consult the
interpretation of status
ET024.
ET025:Telephone button In the event of an
inconsistency, consult the
interpretation of status
ET025.
Wheel actionET017:Wheel actionUPWARDS
DOWNWARDS
INACTIVEIn the event of an
inconsistency, consult the
interpretation of status
ET017.

86D-31V1 MR-413-X44-86D000$100.mif
MULTIMEDIA CONNECTION UNIT
Fault finding – Conformity check86D
BIC
Vdiag No.: 14
FUNCTION: MULTIMEDIA
SUB-FUNCTION: DISPLAY
NOTESOnly carry out a conformity check after a complete check with the diagnostic tool. The
values shown in this conformity check are given as a guide.
Application conditions: Engine stopped, ignition on, and the radio switched on.
FunctionParameter or status
Checked or actionDisplay and notes Fault finding
DisplayAC001:Display testThis command is used
to test the liquid crystal
screen of the display.None
LightingET004:+12 V Side lightsOFF
ON
INVALID
INACTIVEIn the event of an
inconsistency, run fault
finding on the UCH (see
87B, Passenger
compartment
connection unit).
ET007:BrightnessPANEL GAP
NIGHTIn the event of an
inconsistency, consult the
interpretation of ALP 4
Lighting does not
change when the
vehicle lights are
switched on.

86D-32V1 MR-413-X44-86D000$110.mif
86D
BIC
Vdiag No.: 14
Tool status Diagnostic tool title
ET002Radio on/off button
ET004+12 V Side lights
ET007Brightness
ET009Repeat button (only on Clio III)
ET011+ button
ET012- button
ET017Wheel action
ET020Mute button
ET023Source button
ET024Mode button
ET055Telephone button
MULTIMEDIA CONNECTION UNIT
Fault finding – Status summary table