2009 RENAULT TWINGO diagram

Electrical equipment
"The repair procedures given by the manufacturer in this document are based on the
technical specifications current when it was prepared.
The procedures may be modified as a result of changes introduced by the
manufacturer in the production of the various component units and accessories from
which his vehicles are constructed."
V1
All rights reserved by Renault s.a.s.
Edition Anglaise
Copying or translating, in part or in full, of this document or use of the service part
reference numbering system is forbidden without the prior written authority of
Renault s.a.s.
© Renault s.a.s.
V1 MR-413-X44-85A000$000_engTOC.mif
WIPERS - WASHERS
Fault finding - Introduction 85A - 2
Fault finding - List and location of components 85A - 7
Fault finding - Operating diagram 85A - 8
Fault finding - Function 85A - 12
Fault finding - Role of components 85A - 13
Fault finding - configuration and programming 85A - 14
Fault finding - Conformity check 85A - 15
Fault finding - Customer complaints 85A - 17
Fault finding - Fault Finding Chart 85A - 18
85A
MR-413-X44-85A000$000_engTOC.mif

85A-2
MR-413-X44-85A000$100_eng.mif
V1
85A
WIPERS - WASHERS
Fault finding - Introduction
1. SCOPE OF THIS DOCUMENT
This document presents the fault finding procedure applicable to all computers with the following specifications:
2. PREREQUISITES FOR FAULT FINDING
Documentation type
Fault finding procedures (this manual):
–Assisted fault finding (integrated into the diagnostic tool), Dialogys.
Wiring Diagrams:
–Visu-Schéma (CD-ROM), paper.
Types of diagnostic tools
–CLIP
Special tooling required
3. REMINDERS
To run fault finding on the vehicle's computers, switch on the ignition in fault finding mode (+ after ignition feed).Vehicle(s): New Twingo
Function concerned: Wipers/washers
Special tooling required
Multimeter
Elé. 1681 Universal bornier
MR-413-X44-85A000$100_eng.mif

85A-8
MR-413-X44-85A000$300_eng.mif
V1
85A
WIPERS - WASHERS
Fault finding - Operating diagram
List of components and associated component codes:
Component code Component
1016 Passenger compartment fuse box
645 UCH
247 Instrument panel
677 Washer pump
145 Combined wiper-washer
212 Windscreen wiper motor
1415 Light / rain sensor
211 Rear screen wiper motor
MR-413-X44-85A000$300_eng.mif

85A-9
MR-413-X44-85A000$300_eng.mif
V1
WIPERS - WASHERS
Fault finding - Operating diagram85A
Simple windscreen wiper diagram (without rain sensor):
Windscreen wiper diagram with rain sensor:

85A-10
MR-413-X44-85A000$300_eng.mif
V1
WIPERS - WASHERS
Fault finding - Operating diagram85A
Rear screen wiper diagram:
Windscreen washer diagram:

85A-11
MR-413-X44-85A000$300_eng.mif
V1
WIPERS - WASHERS
Fault finding - Operating diagram85A
The vehicle has an automatic wiper function. To activate this function, place the combined wiper-washer in the
intermittent position.
If the car is put into reverse gear when the front wiper motor is in operation, the UCH commands operation of the rear
wiper.
The UCH controls the power supply to the wiper function. It controls the operation of the front wipers, the wiping
speed (intermittent, low-speed, high-speed) and the bi-directional front and rear screen wash pump.
The rain sensor requires an exterior temperature signal, as this enables activation of the wipers to be avoided at
temperatures which might have frozen the wipers.
Summary of the operation of the rain and light sensor
Steering column control,Rain and light sensor
...Interpretation of driver demands...Interpretation of the amount of rain
Front/rear washer pumpUCH
...Windscreen and rear screen
washing...Front and rear wiper management
...Operation management
Multiplex connections
Wire connections
Serial connections