2009 RENAULT TWINGO diagram

Electrical equipment
"The repair procedures given by the manufacturer in this document are based on the
technical specifications current when it was prepared.
The procedures may be modified as a result of changes introduced by the
manufacturer in the production of the various component units and accessories from
which his vehicles are constructed."
V2
All rights reserved by Renault s.a.s.
Edition Anglaise
Copying or translating, in part or in full, of this document or use of the service part
reference numbering system is forbidden without the prior written authority of
Renault s.a.s.
© Renault s.a.s.
V2 MR-413-X44-83E000$000_engTOC.mif
REV COUNTER INSTRUMENT
Vdiag No.: 04
Fault finding - Introduction 83E - 2
Fault finding - List and location of components 83E - 7
Fault finding - Role of components 83E - 8
Fault finding - Operating diagram 83E - 9
Fault finding - Function 83E - 10
Fault finding - Configuration 83E - 11
Fault finding - Conformity check 83E - 12
Fault finding - Status summary table 83E - 14
Fault finding - Interpretation of statuses 83E - 15
Fault finding - Customer complaints 83E - 16
Fault finding - Fault Finding Chart 83E - 17
83E
MR-413-X44-83E000$000_engTOC.mif

83E-2
MR-413-X44-83E000$084_eng.mif
V2
83E
REV COUNTER INSTRUMENT
Fault finding - Introduction
1. SCOPE OF THIS DOCUMENT
This document presents the fault finding procedure applicable to all computers with the following specifications:
2. PREREQUISITES FOR FAULT FINDING
Documentation type
Fault finding procedures (this manual):
–Assisted fault finding (integrated into the diagnostic tool), Dialogys.
Wiring Diagrams:
–Visu-Schéma (CD-ROM), paper.
Type of diagnostic tools
–CLIP
Special tooling required
3. REMINDERS
Procedure
To run fault finding on the vehicle computers, switch on the ignition. Proceed as follows:
–turn the ignition key to APC,
–connect the diagnostic tool and perform the required operations.
To cut off + after ignition feed, proceed as follows:
–disconnect the diagnostic tool,
–turn the ignition key to OFF,
–verify that the forced + after ignition feed has been switched off by checking that the computer warning lights on
the control panel have gone out. Vehicle(s): New Twingo
Function concerned: Rev counterComputer name: Rev counter
3 levels:
–Petrol version
–Diesel version
–Sport version
Vdiag no.: 04
Special tooling required
Multimeter
Elé. 1681 Universal bornier
CPT_V04_PRELI

Vdiag No.: 04
MR-413-X44-83E000$084_eng.mif

83E-9
MR-413-X44-83E000$336_eng.mif
V2
83E
REV COUNTER INSTRUMENT
Fault finding - Operating diagram
1 – + after ignition feed Multiplex connections
2 – + battery feed A – Rev counter
3 – Side light B – Diagnostic tool
4 – Earth C – Instrument panel
5 – Rev counter computer D – Injection
6 – Backlighting E – ABS/ESP
7 – Lighting dimmer
8 – Rev counter needle
9 – ESP warning light

Vdiag No.: 04
MR-413-X44-83E000$336_eng.mif

83E-15
MR-413-X44-83E000$756_eng.mif
V2
83E
REV COUNTER INSTRUMENT
Fault finding - Interpretation of statuses
ET002
SIDE LIGHTS SWITCH
STATUS
DEFINITION–ACTIVE: This status indicates that the side light control is active.
–INACTIVE: This status indicates that the side light control is inactive.
NOTES–Ignition on.
–Side lights on.
If the status of the side light control remains at status INACTIVE, apply the following fault finding procedure.
Check fuse F43 (10A) of the passenger compartment fuse box, component code 1016.
Check that the connection and condition of the rev counter connector are correct (see Wiring Diagram Technical
Note, Twingo II, Component code 995).
If there is a repair method (see Technical Note 6015A, Electrical wiring repair, Wiring: Precautions for repair)
repair the connector, otherwise replace the wiring.
Check the + 12 V feed on connection LPG of component 995.
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for
repair) repair the wiring, otherwise replace it.
Check the continuity and insulation of:
Connection LPG between the passenger compartment fuse box, component code 1016 and the rev
counter, component code 995.
Connection MAM of the rev counter, component code 995.
Connection MAN of the rev counter, component code 995.
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for
repair) repair the wiring, otherwise replace it.
If the fault is still present, contact the techline.
CPT_V04_ET002

Vdiag No.: 04
MR-413-X44-83E000$756_eng.mif