86A-23V2 MR-413-X44-86A100$060.mif
86A
R01-08
Vdiag No.: A4
Thermal protection
Thermal protection is integrated in order to protect the radio.
The functions are restored when the internal temperature falls below 80˚C.
Car radio code
The radio is protected by a two-part anti-theft system:
•A 4-digit code,
•Information exchanged between the instrument panel and the radio.
This code is requested in the following cases:
•New vehicle,
•New radio,
•When a radio is swapped between vehicles.
The radio is protected by a four digit code. This code must be entered using the radio control satellite or the
radio keypad.
Entering the code using the radio control satellite:
Press the lower button on the control to confirm an entry.
Entering the code using the radio:
Enter the digits using buttons 1, 2, 3 and 4, and then confirm with button 6.
If the code is entered incorrectly, the radio will be locked (1 minute for the first error, 2 minutes for the second error,
4 minutes for the third error, etc., for a maximum of 32 minutes after each attempt).
After several attempts, if the fault is still present, contact the Techline.
Some configurations must be programmed after the code has been entered for the first time (see Configuration -
Parameters). These settings are stored when the battery is disconnected.
Reminder:
The radio will operate for approximately 2 minutes in scrambled mode without the code having been entered
(with regular warning beeps).
Note:
If the battery is disconnected, it is not necessary to re-enter the radio anti-theft code.
RADIO
Fault finding – Anti-theft code
86A-43
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults using command RZ003 Fault memory.
Deal with any other faults.
V2 MR-413-X44-86A100$120.mif
RADIO
Fault finding – Interpretation of faults86A
R01-08
Vdiag No.: A4
DF055
PRESENT
OR
STOREDBUTTON JAMMED
1.DEF: Radio front panel button jammed.
NOTESConditions for applying fault finding procedures to stored faults:
The fault is declared present after:
–The + after ignition feed is activated,
–The multimedia system is switched on using the on/off button.
The button concerned is pressed for at least 2 minutes,
Check the conformity of the radio buttons by consulting the following statuses:
–ET005 Source button,
–ET007 Info traffic button,
–ET008 Radio on/off button,
–ET009 CD eject button,
–ET010 Radio preset button 1,
–ET011 Radio preset button 2,
–ET012 Radio preset button 3,
–ET013 Radio preset button 4,
–ET014 Radio preset button 5,
–ET015 Radio preset button 6,
–ET063 MEM button,
–ET068 Volume - button,
–ET069 Volume + button,
–ET070 OK button,
–ET071 Up button,
–ET072 Down button,
–ET073 Left-hand button,
–ET074 Right-hand button,
If the one of the statuses is Pressed, press on the corresponding button so that the status becomes Released.
If the fault is still present, replace the radio (see MR 392 (Clio III) or MR 411 (New Twingo) Mechanical, 86A,
Radio, Radio: Removal - Refitting).
R108_VA4_DF055
86A-87
AFTER REPAIRCarry out another fault finding check on the system.
Deal with any faults.
V2 MR-413-X44-86A100$190.mif
RADIO
Fault finding – Fault Finding Chart86A
R01-08
Vdiag No.: A4
ALP 13 A radio button(s) no longer operates or functions poorly.
NOTESUse the Wiring Diagrams Technical Note for Clio III or New Twingo.
Check button operation. Perform a status reading for
the buttons (see Conformity check).
Are the statuses consistent with button
activation?Contact the Techline.
Replace the radio, component code 261 (see MR 392
(Clio III) or MR 411 (New Twingo) Mechanical, 86A,
Radio, Radio: Removal - Refitting).
YES
NO
R108_VA4_ALP13
