2009 RENAULT TWINGO wiring

86A-34
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults using command RZ003 Fault memory.
Deal with any other faults.
V2 MR-413-X44-86A100$120.mif
RADIO
Fault finding – Interpretation of faults86A
R01-08
Vdiag No.: A4
DF006
CONTINUED
Part B:
Check the connection and condition of the aerial connectors on the radio and navigation system, component codes
261 and 662, and of the connector on the roof aerial, component code 1874.
If the connector(s) is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the insulation, continuity and absence of interference resistance on the following connections:
•46CJ between components 261 and 662,
•TB82 between components 261 and 662.
If the connection(s) are faulty and there is a repair method (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the insulation, continuity and absence of interference resistance on the following connections:
•34EP between components 261 and 1874,
•TB39 between components 261 and 1874.
If the connection(s) are faulty and there is a repair method (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the connections are correct, replace the roof aerial amplifier, component code 1874 (see MR 392, Mechanical,
86A, Radio, Radio aerial: Removal - Refitting).
If the fault is still present, replace the radio (see MR 392, Mechanical, 86A, Radio, Radio: Removal - Refitting).
If the fault persists, contact your Techline.

86A-40
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults using command RZ003 Fault memory.
Deal with any other faults.
V2 MR-413-X44-86A100$120.mif
RADIO
Fault finding – Interpretation of faults86A
R01-08
Vdiag No.: A4
DF039
PRESENT
OR
STOREDBATTERY VOLTAGE
1.DEF: Undervoltage
NOTESConditions for applying fault finding procedures to stored faults:
The fault is declared present after:
– The + after ignition feed is activated,
– The multimedia system is switched on using the on/off button.
– The battery voltage is out of range (12 V < X < 15 V).
Note:
Apply this fault finding method if the fault reappears as present after having been
cleared
Use the Wiring Diagrams Technical Note for Clio III or New Twingo.
Remove the card from the reader or the key from the ignition, then check the condition of the battery.
Check the battery: leaks, incorrectly fitted, loosened battery terminal, and corrosion.
Check the earth connections of the vehicle: battery/chassis, engine/chassis, starter/engine, alternator/engine,
gearbox/chassis.
If the fault is detected, resolve the abnormal contact fault.
Check the battery and perform an alternator supply test (see 16A, Starting, Charging).
Check the conformity of the fuse in the fuse and relay box:
•for New Twingo: F48 (15A),
•for Clio III: F2 (20A) and Unit fuse 710 (15A).
Replace the fuse if not correct.
Disconnect the connector of the radio 261.
Check the continuity of the earth on connection MAO (New Twingo) or MT (Clio III).
If the connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the +12 V supply on connection BCP4 of component 261.
If the supply is not correct, check the insulation, continuity and absence of interference resistance on
connection code BCP4 between components 260 and 261.
If the connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault persists, contact your Techline.
R108_VA4_DF039

86A-41
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults using command RZ003 Fault memory.
Deal with any other faults.
V2 MR-413-X44-86A100$120.mif
RADIO
Fault finding – Interpretation of faults86A
R01-08
Vdiag No.: A4
DF040
DF043
PRESENT
OR
STOREDNO AUDIO CD CHANGER SIGNALS
1.DEF: No communication with the CD changer
NOTESUse the Wiring Diagrams Technical Note for Clio III or New Twingo.
Check for a CD changer in the vehicle.
Check the consistency between the configuration of the radio and the vehicle equipment by reading configuration
LC005 External components and correct if necessary, using SC002 Computer configuration.
Look for any signs of damage to the wiring harness, check the condition and connection of the connectors and
connections of components 261 and the CD changer.
If the connectors or connections are faulty and if there is a repair procedure (see Technical Note 6015A,
Electrical wiring repair, Wiring: Precautions for repair), repair the connector or the wiring, otherwise replace
the wiring.
If the vehicle is equipped with a CD changer, it was fitted as an accessory. Please refer to the handbook delivered
with the product.
If the checks are correct, replace the CD changer.
If the fault persists, contact your Techline.
R108_VA4_DF040/R108_VA4_DF043

86A-46
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults using command RZ003 Fault memory, after pressing the ON/
OFF button.
Deal with any other faults.
V2 MR-413-X44-86A100$120.mif
RADIO
Fault finding – Interpretation of faults86A
R01-08
Vdiag No.: A4
DF064
PRESENT
OR
STOREDACTIVATION SIGNAL
CC.0: Short circuit to earth
CC.1: Short circuit to + 12 V
CO: Open circuit
NOTESConditions for applying fault finding procedures to stored faults:
The fault is declared present after:
–the + after ignition feed is activated,
–the multimedia system has been switched on using the on/off button.
Use the Wiring Diagrams Technical Note for Clio III or New Twingo.
For a vehicle equipped with a navigation system, use the multimedia connection unit
computer, component code 1714, for fault finding.
For a vehicle without a navigation system, use the display computer, component code
653, for fault finding.
Check the condition of the connector on the radio, component code 261, and, depending on the equipment level,
on the display, component code 653, or on the multimedia connection unit, component code 1714.
If the connector(s) is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the insulation, continuity and absence of interference resistance on the following connections:
•34HY between,components 261 and 653 or 1714,
If the connection(s) are faulty and there is a repair method (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the connection is correct, replace the radio (see MR 392 (Clio III) or MR 411 (New Twingo) Mechanical, 86A,
Radio, Radio: Removal - Refitting).
If the fault persists, contact your Techline.
R108_VA4_DF064

86A-60
AFTER REPAIRWhen communication is established, deal with any faults indicated.
V2 MR-413-X44-86A100$190.mif
86A
R01-08
Vdiag No.: A4
ALP 1 No dialogue with the computer
NOTESTry to establish dialogue with a computer on another vehicle to check that the
diagnostic tool is not faulty. If the diagnostic tool is not causing the fault and dialogue
cannot be established with any other computer on the same vehicle, it may be that
a faulty computer is disrupting the fault finding line.
Use a process of successive disconnections to locate this computer.
Check the battery voltage, component code 107, and perform the necessary operations
to obtain the correct voltage (12 V < X < 15 V).
Ensure that the communication conditions are met: + After ignition feed activated and
radio On/Off button pressed.
Use the Wiring Diagrams Technical Note for Clio III or New Twingo.
For a vehicle equipped with a Navigation computer, use component 1714, Multimedia
connection unit, for fault finding on the Multimedia interface unit.
Otherwise use component 653, display computer.
Is the multimedia interface unit recognised
during the multiplex network test?The multimedia interface unit activates other
multimedia system computers.
Consult ALP 1 for the multimedia interface unit
(see 86D, Multimedia interface unit,
Fault finding chart).
Reconfigure the multimedia interface unit
(see 86D, Multimedia interface unit,
Configurations and Programming).
NO
YES
A
R108_VA4_ALP1
RADIO
Fault finding – Fault Finding Chart

86A-62
AFTER REPAIRWhen communication is established, deal with any faults indicated.
V2 MR-413-X44-86A100$190.mif
RADIO
Fault finding – Fault Finding Chart86A
R01-08
Vdiag No.: A4
ALP 1
CONTINUED 2
Check the continuity, insulation and absence of
interference resistance on the following
connection:
•34HU between components 261 and 1714.
If the connection is faulty and there is
a repair procedure (see Technical Note
6015A, Electrical wiring repair, Wiring:
Precautions for repair), repair the wiring,
otherwise replace it. Are the checks correct?
Check the insulation, continuity and absence of
interference resistance on the following
connections:
•34GC between components 662 and 261,
•34GB between components 662 and 261.If the connection or connections are faulty
and there is a repair procedure (see
Technical Note 6015A, Electrical wiring
repair, Wiring: Precautions for repair),
repair the wiring, otherwise replace it. Are the checks correct?
Check the insulation, continuity and absence of
interference resistance on the following
connections:
•34GC and 107X between components 261
and 1714,
•34GB and 107W between components 261
and 1714.Replace the navigation computer,
component code 662 (see MR 392,
Mechanical, 83C, On-board telematics
system, Navigation computer:
Removal – Refitting). Are the checks correct?
Replace the radio, component code 261 (see MR
392, Mechanical, 86A, Radio, Radio: Removal -
Refitting).
C
YES
NO
YES
NO
YES
NO
YES

86A-63
AFTER REPAIRWhen communication is established, deal with any faults indicated.
V2 MR-413-X44-86A100$190.mif
RADIO
Fault finding – Fault Finding Chart86A
R01-08
Vdiag No.: A4
ALP 1
CONTINUED 3
Check the condition and connection of the radio
computer connector, component code 261.
If the connector is faulty and there is a repair
method (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for
repair), repair the connector, otherwise replace
the wiring.
Disconnect the radio computer connector,
component code 261.
Check for + 12 V and earth on the radio between
the following connections:
•BCP4 of component 261 and the MAO
(New Twingo) or MT (Clio III) earth.
Are the checks correct?
Check for + 12 V on the radio computer between
the following connections:
•BCP4 of component 261 and earth.Check the continuity, insulation and
absence of interference resistance of
connection MAO (New Twingo) or MT
(Clio III) between the radio computer,
component code 261 and the earth.
If the connection is faulty and there is a repair
procedure (see Technical Note 6015A,
Electrical wiring repair, Wiring:
Precautions for repair), repair the wiring,
otherwise replace it. Is the result of the check correct?
B
NO
YESD
NO
YES
NO
E

86A-64
AFTER REPAIRWhen communication is established, deal with any faults indicated.
V2 MR-413-X44-86A100$190.mif
RADIO
Fault finding – Fault Finding Chart86A
R01-08
Vdiag No.: A4
ALP 1
CONTINUED 4
Check the continuity, insulation and absence of
interference resistance on the following
connections:
•BCP4 between components 261 and 710,
•BP69 between components 260 and 710
(only for Clio III).
If the connection or connections are faulty and
there is a repair procedure (see Technical Note
6015A, Electrical wiring repair, Wiring:
Precautions for repair), repair the wiring,
otherwise replace it.
E
NO