2009 RENAULT TWINGO Wiring diagrams

17B-163V7 MR-413-X44-17B000$133.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
*RV/LV: Cruise control/speed limiter function
DF1012
PRESENT
OR
STOREDMULTIPLEX SIGNALS CONSISTENCY FOR RV/LV*
1.DEF: Inconsistency
NOTESConditions for applying the fault finding procedure to stored faults:
The fault is present after a road test using the cruise control then the speed limiter
function.
Use the Wiring Diagrams Technical Note for NEW TWINGO, E33, CLIO III,
or MODUS.
Disconnect the battery.
Disconnect the injection computer.
Check the cleanliness and condition of the injection computer connections, component code 120.
If the connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Using the Universal bornier, check for insulation and continuity on the following connections:
●86G between components 120 and 331,
●86M between components 120 and 331.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact the Techline.
SIM32_V44_DF1012 / SIM32_V4C_DF1012 / SIM32_V50_DF1012 / SIM32_V54_DF1012
AFTER REPAIRFollow the instructions to confirm repair:
–If the fault is present, continue to deal with the fault.
–If the fault is stored, ignore it.
Deal with any other faults.
Clear the stored faults.

17B-165V7 MR-413-X44-17B000$133.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
For Clio III and Modus:
DF1072
PRESENT
OR
STOREDAIR CONDITIONING COMPRESSOR RELAY CONTROLCO: Open circuit
CC.0: Short circuit to earth
CC.1: Short circuit to + 12 V
1.DEF: EOBD
NOTESConditions for applying the fault finding procedure to stored faults
The fault is declared present when the engine is running.
Special notes:
CO or CC.1: Not possible to control the air conditioning and the customer is complaining
that driving comfort is reduced.
CO: No impact on the system.
CC.0: The compressor is still active, risk of irreversible damage to the compressor (loss
of capacity). The customer is complaining that the air conditioning is operating
continuously.
Use the Wiring Diagrams Technical Note for NEW TWINGO, E33, CLIO III, or
MODUS.
Check the condition of the UPC connectors, component code 1337.
Check the condition of the engine management computer connector, component code 120.
If the connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Run a test on the UPC computer (see 87G, Engine compartment connection unit).
Run command AC180 Air conditioning compressor relay control and check for + 12 V on connection 38R of
the air conditioning compressor clutch, component code 171.
If the fault is still present, contact the Techline.
SIM32_V44_DF1072 / SIM32_V4C_DF1072 / SIM32_V50_DF1072 / SIM32_V54_DF1072
AFTER REPAIRFollow the instructions to confirm repair:
–If the fault is present, continue to deal with the fault.
–If the fault is stored, ignore it.
Deal with any other faults.
Clear the stored faults.

17B-175V7 MR-413-X44-17B000$151.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET021HIGH-SPEED FAN REQUEST–Active
–Inactive
STATUS
DEFINITIONACTIVE: This status indicates that the high-speed fan assembly is active.
INACTIVE: This status indicates that the high-speed fan assembly is inactive.
NOTESSpecial notes:
Apply the checks only if statuses ACTIVE and INACTIVE are inconsistent.
Refer to the Wiring Diagrams Technical Note for NEW TWINGO, E33, CLIO III
or MODUS.
Conformity check: Engine stopped and ignition on, or engine running at idle speed, and engine coolant
temperature > 80˚C.
"ACTIVE"
or
"INACTIVE"Fan unit 2 starts when the coolant temperature exceeds 102˚C and stops when it falls
below 99˚C.
Sensor electrical conformity
SIM32_V44_ET021/SIM32_V4C_ET021/SIM32_V50_ET021/SIM32_V54_ET021
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
Repeat the conformity check from the start.

17B-178V7 MR-413-X44-17B000$151.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET022LOW-SPEED FAN REQUEST–Active
–Inactive
STATUS
DEFINITIONACTIVE: This status indicates that the low-speed fan assembly is active.
INACTIVE: This status indicates that the low-speed fan assembly is inactive.
NOTESSpecial notes:
Apply the checks only if statuses ACTIVE and INACTIVE are inconsistent.
Refer to the Wiring Diagrams Technical Note for NEW TWINGO, E33, CLIO III or
MODUS.
Conformity check: Engine stopped and ignition on, or engine running at idle speed, and engine coolant
temperature > 80˚C.
"ACTIVE"
or
"INACTIVE"To ensure cooling, when the engine is running, fan assembly 1 is activated when
the coolant temperature exceeds 99˚C and stops when it falls below 96˚C.
Sensor electrical conformity
SIM32_V44_ET022/SIM32_V4C_ET022/SIM32_V50_ET022/SIM32_V54_ET022
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
Repeat the conformity check from the start.

17B-181V7 MR-413-X44-17B000$151.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET023FAST IDLE SPEED REQUEST–Present
–Absent
STATUS
DEFINITIONPRESENT: The status indicates that the fast idle speed request is active.
ABSENT: The status indicates that the fast idle speed request is inactive.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system operation
programming.
Refer to the Wiring Diagrams Technical Note for NEW TWINGO, E33, CLIO III
or MODUS.
Conformity check: Engine stopped and ignition on, or engine running at idle speed, and engine coolant
temperature > 80˚C.
PRESENT
OR
ABSENTUCH requests the injection system to increase the idling speed.
ABSENT: The UCH has not formulated a request.
PRESENT: The UCH has formulated a request.
If ET023 is inconsistent, test the multiplex network using the diagnostic tool
(see 88B, Multiplexing). If the test is correct, refer to the UCH fault finding procedure
(see 87B, Passenger compartment connection unit) and for Clio III or Modus,
run fault finding on the Protection and Switching Unit (see 87G, Engine
compartment connection unit).
SIM32_V44_ET023/SIM32_V4C_ET023/SIM32_V50_ET023/SIM32_V54_ET023
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

17B-226V7 MR-413-X44-17B000$152.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET405CLUTCH PEDAL SWITCH
STATUS
DEFINITIONACTIVE: this status indicates that the clutch pedal is depressed.
INACTIVE: this status indicates that the clutch pedal is released.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system operation
programming.
Use the Wiring Diagrams Technical Note for NEW TWINGO, E33, CLIO III
or MODUS.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80˚C
"ACTIVE"Clutch pedal depressed.
Non-conformity of the brake signals and or the clutch switch signals can cause the
engine to race during gear changes.
"INACTIVE"Clutch pedal released.
Non-conformity of the brake signals and or the clutch switch signals can cause the
engine to race during gear changes.
SIM32_V44_ET405/SIM32_V4C_ET405/SIM32_V50_ET405/SIM32_V54_ET405
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.

17B-252V7 MR-413-X44-17B000$153.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET673JAMMED ACCELERATOR PEDAL–YES
–NO
STATUS
DEFINITIONYES: This status indicates that the accelerator pedal is detected to be jammed.
NO: This status indicates that the accelerator pedal is not detected to be jammed.
NOTESSpecial notes:
Apply this procedure only if the status is YES.
Use the Wiring Diagrams Technical Note for NEW TWINGO, E33, CLIO III
or MODUS.
Conformity check: Engine stopped and ignition on, or engine running, and engine coolant
temperature > 80˚C
YES
OR
NOThis status varies when the ignition is on or the engine is running depending on the
status of the accelerator pedal.
Check the condition of the connectors of the brake switch (component code 160), of the accelerator potentiometer
(component code 921), and of the engine management computer (component code 120).
If the connector or connectors are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
SIM32_V44_ET673 / SIM32_V4C_ET673 / SIM32_V50_ET673 / SIM32_V54_ET673
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

17B-255V7 MR-413-X44-17B000$153.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET703CRUISE CONTROL/SPEED LIMITER BUTTONS
STATUS
DEFINITIONRESUME: R button pressed.
SUSPEND: 0 button pressed.
INCREASE: Increase button pressed.
MINUS: Decrease button pressed.
INACTIVE: This status indicates that no button has been pressed.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system operation
programming.
Use the Wiring Diagrams Technical Note for NEW TWINGO, E33, CLIO III
or MODUS.
Conformity check: Engine stopped and ignition on, or engine running, and engine coolant
temperature > 80˚C
"INACTIVE"When no button has been pressed.
In the event of a fault, refer to the interpretation of status ET703.
"SUSPEND"'0' button pressed.
In the event of a fault, refer to the interpretation of status ET703.
"REACTIVATE"'R' button pressed.
In the event of a fault, refer to the interpretation of status ET703.
SIM32_V44_ET703 / SIM32_V4C_ET703 / SIM32_V50_ET703 / SIM32_V54_ET703
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.