2009 RENAULT TWINGO engine

17B-195V7 MR-413-X44-17B000$151.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET054IDLING SPEED REGULATION–Active
–Inactive
STATUS
DEFINITIONACTIVE: This status indicates that idle speed regulation is active.
INACTIVE: This status indicates that idle speed regulation is inactive.
NOTESThere must be no present or stored faults.
Special notes:
Only perform these tests if the parameters do not correspond with the system operation
programming.
Conformity check: engine stopped and ignition on.
"INACTIVE"The status becomes active when the engine is started.
Conformity check: engine running at idle speed, engine coolant temperature > 80˚C.
ACTIVEThe status becomes active when the engine is started.
SIM32_V44_ET054/SIM32_V4C_ET054/SIM32_V50_ET054/SIM32_V54_ET054
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
Repeat the conformity check from the start.

17B-196V7 MR-413-X44-17B000$151.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET054
CONTINUED
IDLING SPEED TOO LOW
Check:
–engine oil level (too high, splashing),
–that the exhaust pipe is not blocked (catalytic converter damaged),
–the cleanliness and conformity of the air filter,
–that the air inlet circuit is not blocked,
–that the throttle valve assembly is not clogged,
–the condition and conformity of the spark plugs,
–the fuel circuit sealing,
–the fuel pressure and the flow (see MR 392 (Clio III), MR 385 (Modus), MR 411 (New Twingo), or MR 442
(E33), Mechanical, 13A, Fuel supply),
–the condition and cleanliness of the injectors,
–the cylinder compression's,
–the timing setting.
Repair or replace the faulty components, if necessary.
IDLING SPEED TOO HIGH
Check:
–engine oil level (too high, splashing),
–for the fittings in the oil vapour rebreathing system,
–the sealing between the throttle valve and inlet manifold,
–the manifold pressure sensor sealing,
–the fuel vapour absorber bleed, which must not be jammed open,
–the fuel vapour absorber bleed system sealing,
–the brake servo system sealing,
–the sealing between the inlet manifold and cylinder head,
–the oil vapour recovery circuit sealing between the inlet manifold and cylinder head,
–the fuel pressure and the flow (see MR 392 (Clio III), MR 385 (Modus), MR 411 (New Twingo), or MR 442
(E33), Mechanical, 13A, Fuel supply),
–the condition and cleanliness of the injectors,
–the cylinder compression's,
–the timing adjustment,
Repair or replace the faulty components, if necessary.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

17B-197V7 MR-413-X44-17B000$151.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET056DOUBLE RICHNESS LOOP
STATUS
DEFINITIONACTIVE: The status indicates that the double richness loop is active.
INACTIVE: The status indicates that the double richness loop is inactive.
NOTESThere must be no present or stored faults.
Special notes:
Only perform these tests if the parameters do not correspond with the system operation
programming.
Conformity check: Engine stopped and ignition on, or engine running at idle speed, and engine coolant
temperature > 80˚C.
"INACTIVE"
or
ACTIVEThis status is only inactive if one of the two oxygen sensors is in poor condition.
In the event of a fault, apply the interpretation of faults DF082 Upstream oxygen
sensor heating circuit, DF083 Downstream oxygen sensor heating circuit,
DF092 Upstream oxygen sensor circuit, DF093 Downstream oxygen
sensor circuit.
SIM32_V44_ET056/SIM32_V4C_ET056/SIM32_V50_ET056/SIM32_V54_ET056
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

17B-198V7 MR-413-X44-17B000$151.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET057
ET058
ET059
ET060MISFIRING ON CYLINDER 1
MISFIRING ON CYLINDER 2
MISFIRING ON CYLINDER 3
MISFIRING ON CYLINDER 4
STATUS
DEFINITIONYES: This status indicates that a combustion misfire has been detected on the cylinder.
NO: This status indicates that a combustion misfire has not been detected on the
cylinder.
NOTESSpecial note:
Only perform the tests if the statuses do not correspond with the system programming
functions.
Conformity check: engine running at idle speed, engine coolant temperature > 80˚C.
"YES"
or
"NO"For normal engine operation, the status must be NO.
'In the event of a fault, apply the interpretation of faults DF059 Combustion misfire
in cylinder 1, DF060 Combustion misfire in cylinder 2, DF061 Combustion
misfire in cylinder 3 and DF062 Combustion misfire in cylinder 4 according to
the cylinder in question.
SIM32_V44_ET057/SIM32_V4C_ET057/SIM32_V50_ET057/SIM32_V54_ET057/SIM32_V44_ET058/SIM32_V4C_ET058/SIM32_V50_ET058/
SIM32_V54_ET058/SIM32_V44_ET059/SIM32_V4C_ET059/SIM32_V50_ET059/SIM32_V54_ET059/SIM32_V44_ET060/SIM32_V4C_ET060/
SIM32_V50_ET060/SIM32_V54_ET060
AFTER REPAIRRepeat the conformity check from the start.

17B-199V7 MR-413-X44-17B000$151.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET061CYLINDER
1 RECOGNITION
–Completed
–Not completed
STATUS
DEFINITIONCOMPLETED: This status indicates that the cylinder 1 injector command recognition
is active.
NOT COMPLETED: This status indicates that the cylinder 1 injector command
recognition is inactive.
NOTESThere must be no present or stored faults.
Special notes:
Only perform these tests if the parameters do not correspond with the system operation
programming.
Conformity check: Engine stopped and ignition on, or engine running at idle speed, and engine coolant
temperature > 80˚C.
COMPLETED
or
NOT
PERFORMEDThe status is completed when the engine is started if the engine phasing is correct.
Run command RZ005 Programming and program the engine flywheel target
(see Configurations and Programming). Check the programming using ET089
Flywheel target programming.
Engine phasing:
On engines without a camshaft sensor, the engine phasing is performed by software. A "Memo-phasing" program
is run first to phase the engine management on starting according to the data saved from the previous setting. Wait
30 seconds (for the data to be saved) before disconnecting the computer.
Then, a second program confirms the first decision. It is based on torque analysis. The torque calculation is based
on the analysis of the time taken for the engine flywheel teeth to pass by. The engine speed should be between
320 rpm and 5,000 rpm.
Run command RZ005 Programming and program the engine flywheel target (see Configurations and
Programming). Check the programming using ET089 Flywheel target programming.
SIM32_V44_ET061/SIM32_V4C_ET061/SIM32_V50_ET061/SIM32_V54_ET061
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

17B-200V7 MR-413-X44-17B000$151.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET062FLYWHEEL SIGNAL–detected
–not detected
STATUS
DEFINITIONDETECTED: This status indicates that the engine flywheel signal is detected.
NOT DETECTED: This status indicates that the engine flywheel signal is not detected.
NOTESThere must be no present or stored faults.
Special notes:
Only perform these tests if the parameters do not correspond with the system operation
programming.
Conformity check: engine stopped and ignition on.
NOT DETECTEDThe engine flywheel signal is detected after the engine is started.
In the event of a fault apply the interpretation for DF154 Flywheel signal sensor
circuit.
Conformity check with engine running at idle speed, engine coolant temperature > 80˚C
DETECTED The engine flywheel signal is detected after the engine is started.
In the event of a fault apply the interpretation for DF154 Flywheel signal sensor
circuit.
SIM32_V44_ET062/SIM32_V4C_ET062/SIM32_V50_ET062/SIM32_V54_ET062
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

17B-201V7 MR-413-X44-17B000$151.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET075PEDAL NO LOAD AND THROTTLE VALVE CLOSED
STATUS
DEFINITIONYES: This status indicates that the motorised throttle is closed and that there is no load
on the accelerator pedal.
NO: This status indicates that the motorised throttle is definitely not closed and/or that
there is some load on the accelerator pedal.
NOTESThere must be no present or stored faults.
Special notes:
Only perform these tests if the parameters do not correspond with the system operation
programming.
Conformity check: Engine stopped and ignition on, or engine running at idle speed, and engine coolant
temperature > 80˚C.
"YES"Without action on the pedal, the status ET075 is YES.
"NO"Apply the interpretation of PR030 Accelerator pedal position.
SIM32_V44_ET075/SIM32_V4C_ET075/SIM32_V50_ET075/SIM32_V54_ET075
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

17B-202V7 MR-413-X44-17B000$151.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET076STARTING
STATUS
DEFINITIONPROHIBITED: This status indicates that starting is not possible.
AUTHORISED: This status indicates that starting is possible.
NOTESSpecial note:
Only perform the tests if the statuses do not correspond with the system programming
functions.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80˚C
"PROHIBITED"Refer to the UCH fault finding note, (see 87B, Passenger compartment connection
unit) or to the Protection and Switching Unit fault finding note, (see 87G, Engine
compartment connection unit).
"AUTHORISED"Refer to the UCH fault finding note, (see 87B, Passenger compartment connection
unit) or to the Protection and Switching Unit fault finding note, (see 87G, Engine
compartment connection unit).
SIM32_V44_ET076/SIM32_V4C_ET076/SIM32_V50_ET076/SIM32_V54_ET076
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.