2009 RENAULT TWINGO engine

82D-24
MR-413-X44-82D000$700_eng.mif
V1
ACCESS/SAFETY
Fault finding - Conformity check82D
SUB-FUNCTION: PROTECTION (CONTINUED 1)
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
Computer Order FunctionParameter or Status
checked or ActionDisplay and
NotesFault finding
UCH (see 87B,
Passenger
compartment
connection unit)5
KeyET045:Radiofrequency
signal receivedYES = When the
UCH receives a
radiofrequency
signal.
NO = When the
UCH does not
receive a
Radiofrequency
signal.In the event of a fault,
refer to the
interpretation of
status ET045
(see 87B, Passenger
compartment
connection unit).
6ET193:Radiofrequency
signal from a key
allocated to the
vehiclePRESENT =
Reception of a
radiofrequency
signal from a key
allocated to the
vehicle.
ABSENT = No
reception of
frequency signal or
reception of
frequency signal
from a key not
allocated to the
vehicle.In the event of a fault,
refer to the
interpretation of
status ET193
(see 87B, Passenger
compartment
connection unit).
7ET240:Key frequency
(in MHz)433
NONEIf "NONE", check that
there is a
radiofrequency key by
trying with another key
(see 87B, Passenger
compartment
connection unit).
8PR056:Number of keys
allocatedX key(s)In the event of a fault,
refer to the
interpretation of
PR056 (see 87B,
Passenger
compartment
connection unit).

82D-25
MR-413-X44-82D000$700_eng.mif
V1
ACCESS/SAFETY
Fault finding - Conformity check82D
SUB-FUNCTION: PROTECTION (CONTINUED 2)
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
Computer Order FunctionParameter or Status
checked or ActionDisplay and
NotesFault finding
UCH (see 87B,
Passenger
compartment
connection unit)9
InjectionET229:Injection
immobiliser
codePROGRAMMED
NOT
PROGRAMMED
UNDETERMINEDIn the event of a fault, refer
to the interpretation of
status ET229 (see 87B,
Passenger compartment
connection unit).
10 ET250:InjectionNOT
PROTECTED
PROTECTEDIn the event of a fault, refer
to the interpretation of
status ET250
(see 17B, Petrol
injection, Conformity
check, Protection)
(see 13B, Diesel
injection, Conformity
check, Protection)
(see 87B, Passenger
compartment
connection unit).
11Starter actuatorET239:Ignition switch
positionINACTIVE
+ ACCESSORIES
+ after ignition
feed.
+ START FEEDIn the event of a fault, refer
to the interpretation of
status ET239 (see 87B,
Passenger compartment
connection unit).

82D-26
MR-413-X44-82D000$700_eng.mif
V1
ACCESS/SAFETY
Fault finding - Conformity check82D
SUB-FUNCTION: PROTECTION (CONTINUED 3)
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
Computer Order FunctionParameter or Status
checked or ActionDisplay and Notes Fault finding
Diesel
Injection
(see 13B,
Diesel
Injection)1Computer + after
ignition feedET001:Computer +
after ignition
feedPRESENT
Indicates + after ignition
computer feed.
PRESENT/ABSENTIn the event of a fault,
use the interpretation
of faults DF047
"Computer feed
voltage" and DF015
"Main relay control
circuit ".
2Engine
immobiliserET003:Engine
immobiliser INACTIVE
- INACTIVE: The
injection computer has
recognised the
immobiliser code
transmitted by the UCH.
- ACTIVE: The injection
computer has not
recognised the
immobiliser code
transmitted by the UCH.If ACTIVE, use the
"help" for ET003 on
the tool.
3Code
programmedET006:Code
programmedYES
States whether the
immobiliser code has
been programmed by the
computer or not.
YES: Code programmed
NO: Code not
programmed into the
injection computerIf NO, test the
multiplex network.
4StartingET076:StartingAUTHORISED
Indicates whether or not
starting has been
authorised by the
injection
AUTHORISED: injection
authorises starting.
PROHIBITED: Injection
does not authorise
startingIf PROHIBITED,
carry out a complete
fault finding
procedure on the
preheating system.

82D-27
MR-413-X44-82D000$700_eng.mif
V1
ACCESS/SAFETY
Fault finding - Conformity check82D
SUB-FUNCTION: PROTECTION (CONTINUED 4)
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
Computer Order FunctionParameter or Status
checked or ActionDisplay and Notes Fault finding
Petrol
Injection
(see 17B,
Petrol
Injection)1Computer +
after ignition
feedET001:Computer +
after ignition
feedPRESENT
Indicates + after
ignition computer feed.
PRESENT/ABSENTIn the event of a
fault, use the
interpretation of
faults DF047
"Computer feed
voltage" and
DF015 "Main relay
control circuit".
2Engine
immobiliserET003:Engine
immobiliser INACTIVE
- INACTIVE: The
injection computer has
recognised the
immobiliser code
transmitted by the UCH.
- ACTIVE: The injection
computer has not
recognised the
immobiliser code
transmitted by the UCH.If ACTIVE, use "the
help" for ET003 on
the tool.
3Code
programmedET341:Immobiliser
code
programmedYES
States whether the
immobiliser code has
been programmed by
the computer or not.
YES: Code programmed
NO: Code not
programmed into the
injection computerIn the event of a
fault, refer to the
interpretation of
status ET341
"Immobiliser code
programmed".
4StartingET076:StartingAUTHORISED
Indicates whether or not
starting has been
authorised by the
injection
AUTHORISED: injection
authorises starting.
PROHIBITED: Injection
does not authorise
startingIf PROHIBITED,
carry out a complete
fault finding
procedure on the
preheating system.

82D-28
MR-413-X44-82D000$700_eng.mif
V1
ACCESS/SAFETY
Fault finding - Conformity check82D
SUB-FUNCTION: STARTING
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
Computer Order FunctionParameter or Status
checked or ActionDisplay and
NotesFault finding
UCH (see 87B,
Passenger
compartment
connection
unit)1
EngineET239:Ignition switch
positionINACTIVE
+ ACCESSORIES
+ after ignition
feed.
+ START FEEDIn the event of a fault, refer to the
interpretation of status ET239
(see 87B, Passenger
compartment
connection unit).
And (see 17B, Petrol Injection,
Conformity check, Protection)
(see 13B, Diesel Injection,
Conformity check,
Protection).
2ET142:Engine
operating phaseSTOPPED
STARTING
RUNNING
STALLEDIn the event of a fault, refer to the
interpretation of status ET142
(see 87B, Passenger
compartment
connection unit).
And (see 17B, Petrol Injection,
Conformity check, Protection)
(see 13B, Diesel Injection,
Conformity check,
Protection).
3PR025:Engine speed0 rpmIn the event of a fault, carry out a
fault finding on the multiplex
network (see 88B).
And (see 17B, Petrol Injection,
Conformity check, Protection)
(see 13B, Diesel Injection,
Conformity check,
Protection).

82D-29
MR-413-X44-82D000$700_eng.mif
V1
ACCESS/SAFETY
Fault finding - Conformity check82D
SUB-FUNCTION: STARTING (CONTINUED):1
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
Computer Order FunctionParameter or Status
checked or ActionDisplay and Notes Fault finding
Diesel
Injection
(see 13B,
Diesel
Injection)1EngineET038:Engine– NOT RUNNING
– RUNNINGNONE
2StartingET076:StartingAUTHORISED
Indicates whether or not
starting has been
authorised by the
injection
AUTHORISED: injection
authorises starting.
PROHIBITED: Injection
does not authorise
startingIf PROHIBITED, carry out
a complete fault finding
procedure on the
preheating system.
3AirbagET077:Impact
detectedNO
YES (impact stored by
the injection computer).If ET077 is YES:
Switch off the ignition for
10 seconds, then switch it
back on, so the engine can
be restarted. Then clear
any faults.

82D-30
MR-413-X44-82D000$700_eng.mif
V1
ACCESS/SAFETY
Fault finding - Conformity check82D
SUB-FUNCTION: STARTING (CONTINUED 2)
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
Computer Order FunctionParameter or Status
checked or ActionDisplay and Notes Fault finding
Petrol
Injection
(see 17B,
Petrol
Injection)1EngineET038:Engine– NOT RUNNING
– RUNNINGNONE
2ET048:Actuator
relay control– ACTIVE
– INACTIVEIn the event of a fault,
consult the interpretation of
status ET048 "Actuator
control relay".
3StartingET076:StartingAUTHORISED
Indicates whether or not
starting has been
authorised by the
injection
AUTHORISED: injection
authorises starting.
PROHIBITED: Injection
does not authorise
startingIf PROHIBITED, carry out a
complete fault finding
procedure on the
preheating system.
4AirbagET077:Impact
detectedNO
YES (impact stored by
the injection computer).If ET077 is YES:
Switch off the ignition for
10 seconds, then switch it
back on, so the engine can
be restarted. Then clear
any faults.

82D-38
MR-413-X44-82D000$900_eng.mif
V1
ACCESS/SAFETY
Fault finding - Fault Finding Chart82D
ALP 23Renault Anti-Intruder Device
operating fault
NOTESOnly check this customer complaint after performing a complete check with the
diagnostic tool.
Run a multiplex network test (see 88B, Multiplex).
Note:
When this function is activated and if all the doors are closed, the vehicle can be
locked automatically when driving over speeds of 4 mph (7 km/h).
To activate or deactivate this function, the user must press and hold the central door
locking button, with the engine running.
The function is deactivated with a single beep, and is activated with 2 beeps.
Whenever a door is opened then closed over this limit, the UCH automatically locks
the vehicle.
The RAID function can only be performed a maximum of 5 times per trip.
Check the following conformities:
CF009 Deadlocking with LC003 Deadlocking.
CF108 "Renault Anti-Intruder Device" with LC040 "Renault Anti-Intruder Device".
CF192 Central door locking with LC093 Central door locking.
Carry out a road test to check that the RAID function
is active (locking above 4 mph (7 km/h)).
Is the function active?
YES
Check that none of the door statuses is "OPEN".
NOActivate the function by pressing and holding
the electric door locking button, with the
engine running.
AFTER REPAIRCarry out another fault finding check on the system.
UCH_V44_ALP23