2009 RENAULT TWINGO wheel

31A-52
FRONT AXLE COMPONENTS
Front anti-roll bar: Removal - Refitting
EQ UIPMENT LEVEL EA0 or EQUIPMENT LEVEL EA1 or EQUIPMENT LEVEL EA3 or EQUIPMENT LEVEL EA5
or EQUIPMENT LEVEL EAG or EQUIPMENT LEVEL EZ2 or EQUIPMENT LEVEL EZ4
31A
Anti-roll bar specifications:
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (02A, Lifting equipment).
aRemove the front axle subframe (see 31A, Front
axle components, Front axle subframe: Removal
- Refitting, page 31A-43) .II - OPERATION FOR REMOVAL OF PART
CONCERNED
aCompress the anti-roll bar rubber mounting bush on
the wheel side using the (Sus. 1413).
aRemove:
-the bolt (1) from the anti-roll bar on the wheel side,
-the rubber mounting bush from the anti-roll bar,
-the anti-roll bar bearing bolts (2) ,
-the anti-roll bar bearings,
-the anti-roll bar,
-the rubber mounting bush from the anti-roll bar
bearing.
REFITTING
REFITTING OPERATION FOR PART CONCERNED
aRefit:
-the anti-roll bar bearing rubber mounting bush,
-the anti-roll bar.
aFit the anti-roll bar bearings into the subframe neck. Special tooling required
Sus. 1413Rubber mounting compres-
sor for fitting the anti-roll bar.
(wheel end).
Sus. 1824Fork for fitting the anti-roll bar
centre bearings.
Tightening torquesm
anti-roll bar bearing
bolts on the subframe35 Nm
anti-roll bar bolt on the
wheel side14 Nm
Engine Ø of the strut in
mm
D7F 25
D4F, K9K 26
119406

31A-53
FRONT AXLE COMPONENTS
Front anti-roll bar: Removal - Refitting
EQ UIPMENT LEVEL EA0 or EQUIPMENT LEVEL EA1 or EQUIPMENT LEVEL EA3 or EQUIPMENT LEVEL EA5
or EQUIPMENT LEVEL EAG or EQUIPMENT LEVEL EZ2 or EQUIPMENT LEVEL EZ4
31A
aFit the (Sus. 1824) (3) on the anti-roll bar.
aLift the (Sus. 1824).
aRefit the anti-roll bar bearing bolts (4) .
aTorque tighten the anti-roll bar bearing bolts on
the subframe (35 Nm).
aRefit:
-the anti-roll bar rubber mounting bush on the wheel
side,
-the anti-roll bar bolt on the wheel side.aRefit the front axle subframe (see 31A, Front axle
components, Front axle subframe: Removal -
Refitting, page 31A-43) .
aCompress the anti-roll bar rubber mounting bush on
the wheel side using the (Sus. 1413) (5) .
aRefit the anti-roll bar nut (6) on the wheel side.
aTorque tighten the anti-roll bar bolt on the wheel
side ( 14 Nm).
119403
119404
12992

31A-54
FRONT AXLE COMPONENTS
Front anti-roll bar: Removal - Refitting
EQ UIPMENT LEVEL SPORT
31A
Anti-roll bar specifications:
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (02A, Lifting equipment).
aRemove:
-the front wheels (see 35A, Wheels and tyres,
Wheel: Removal - Refitting, page 35A-1) ,
-the wheel arch liners (see Front wheel arch liner:
Removal - Refitting) (55A, Exterior protection),
-the front axle subframe (see 31A, Front axle com-
ponents, Front axle subframe: Removal - Refit-
ting, page 31A-43) .II - OPERATION FOR REMOVAL OF PART
CONCERNED
aRemove:
-the nuts (1) of the anti-roll bar tie rods,
-the anti-roll bar tie rods from the anti-roll bar.
aRemove:
-the anti-roll bar bearing bolts (2) ,
-the anti-roll bar bearings (3) ,
-the anti-roll bar, Special tooling required
Sus. 1824Fork for fitting the anti-roll bar
centre bearings.
Tightening torquesm
anti-roll bar bearing
bolts35 N.m
Colour∅ of the strut in mm
Brown 21
Blue 20132461
132457

31A-55
FRONT AXLE COMPONENTS
Front anti-roll bar: Removal - Refitting
EQ UIPMENT LEVEL SPORT
31A
-the rubber mounting bushes of the anti-roll bar
bearings.
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
aRefit:
-the rubber mounting bushes on the anti-roll bar
bearings,
-the anti-roll bar,
-the anti-roll bar bearings.
aFit the (Sus. 1824) on the anti-roll bar.aLift the (Sus. 1824).
aRefit the anti-roll bar bearing bolts.
aTorque tighten the anti-roll bar bearing bolts (35
N.m).
aRefit the anti-roll bar tie rods on the anti-roll bar.
II - FINAL OPERATION.
aRefit:
-the front axle sub-frame (see 31A, Front axle
components, Front axle subframe: Removal -
Refitting, page 31A-43) ,
-the wheel arch liners (see Front wheel arch liner:
Removal - Refitting) (55A, Exterior protection),
-the front wheels (see 35A, Wheels and tyres,
Wheel: Removal - Refitting, page 35A-1) .
119403
119404

33A-1
REAR AXLE COMPONENTS
Rear brake pads: Removal - Refitting
EQ UIPMENT LEVEL SPORT
33A
When replacing brake pads, be sure to replace the
pads on the opposite side.
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (02A, Lifting equipment).
aRelease the parking brake.
aRemove the rear wheels (see 35A, Wheels and ty-
res, Wheel: Removal - Refitting, page 35A-1) .II - OPERATION FOR REMOVAL OF PART
CONCERNED
aUnclip the parking brake cable from the brake calli-
per at (1) .
aMove aside the parking brake cable.
aRemove the lower bolt (2) of the brake calliper guide
pin.
aTilt the brake calliper over.
aRemove the brake pads (3) from the brake calliper
mounting. Special tooling required
Fre. 1190-01Brake calliper piston return
tool.
Tightening torquesm
new lower bolts of the
calliper guide pins35 N.m
WARNING
To avoid damaging the parking brake cable protec-
tors and causing premature wear of the system, do
not handle the cables with a tool.
132468
132466

33A-3
REAR AXLE COMPONENTS
Rear brake pads: Removal - Refitting
EQ UIPMENT LEVEL SPORT
33A
aFit:
-the brake callipers,
-the parking brake cables.
aTorque tighten the new lower bolts of the calliper
guide pins (35 N.m).
aClip on the handbrake cables.
III - FINAL OPERATION
aRefit the rear wheels (see 35A, Wheels and tyres,
Wheel: Removal - Refitting, page 35A-1) .
IMPORTANT
To avoid any accident, bring the pistons, brake
pads and brake discs into contact by depressing
the brake pad several times.

33A-7
REAR AXLE COMPONENTS
Rear brake calliper: Removal - Refitting
EQ UIPMENT LEVEL SPORT
33A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (02A, Lifting equipment).
aRelease the parking brake.
aPosition a pedal press on the brake pedal to limit
the outflow of brake fluid.
aRemove the rear wheel (see 35A, Wheels and ty-
res, Wheel: Removal - Refitting, page 35A-1) .II - OPERATION FOR REMOVAL OF PART
CONCERNED
aUnclip the parking brake cable from the brake calli-
per at (1) .
aMove aside the parking brake cable.
aLoosen the calliper brake pipe union (2) .
aRemove:
-the brake calliper guide pin bolts (3) ,
-the brake calliper from the mounting,
-the union between the brake pipe and the calliper,
-the brake calliper.
REFITTING
I - REFITTING PREPARATION OPERATION
aClean using a wire brush and BRAKE CLEANER
(see Vehicle: Parts and consumables for the re-
pair) (04B, Consumables - Products):
-the calliper supports,
-the callipers.
aAlways replace the brake calliper guide pin bolts. Special tooling required
Fre. 1190-01Brake calliper piston return
tool.
Equipment required
pedal press
Tightening torquesm
new bolts on the brake
calliper guide pins35 N.m
brake pipe union on the
calliper13 N.m
WARNING
To avoid damaging the parking brake cable protec-
tors and causing premature wear of the system, do
not handle the cables with a tool.
132468

33A-8
REAR AXLE COMPONENTS
Rear brake calliper: Removal - Refitting
EQ UIPMENT LEVEL SPORT
33A
aPush the piston to the bottom of its housing using
the (Fre. 1190-01).
II - REFITTING OPERATION FOR PART
CONCERNED
aRefit the brake calliper on the calliper mounting.
aTorque tighten:
-the new bolts on the brake calliper guide pins
(35 N.m),
-the brake pipe union on the calliper (13 N.m).
aFit the parking brake cable.
aClip the handbrake on the brake calliper.
III - FINAL OPERATION
aRefit the rear wheel (see 35A, Wheels and tyres,
Wheel: Removal - Refitting, page 35A-1) .
aRemove the pedal press from the brake pedal.
aBleed the brake circuit (see 30A, General informa-
tion, Braking circuit: Bleed, page 30A-4) .
106309
IMPORTANT
To avoid any accident, bring the pistons, brake
pads and brake discs into contact by depressing
the brake pad several times.