2009 RENAULT TWINGO wheel torque

36B-30
MR-413-X44-36B000$536.mif
V2
POWER – ASSISTED STEERING
Fault finding – Conformity check
EPAS
Vdiag No.: 04 - 08
36B
SUB-FUNCTION: ASSISTANCE (CONTINUED)
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool.
Application conditions: engine at idle speed, no movement of the steering
wheel, front wheels straight ahead.
FunctionParameter or Status
Checked or ActionDisplay and notes Fault finding
AssistancePR001:Torque applied
to the steering
wheel0 Nm (+ 0.2 Nm)In the event of a fault, apply the
interpretation of parameter
PR001.
OutputPR132: Current setpoint
(45 A)0 A
Note: these two
parameters must be
approximately the
same.In the event of a fault, apply the
interpretation of parameters
PR132 and PR130.
PR130: Motor power (45
A)
PR131: Current setpoint
(60 A)0 A
Note: these two
parameters must be
approximately the
same.In the event of a fault, apply the
interpretation of parameters
PR131 and PR129.
PR129: Motor power (60
A)

36B-35
MR-413-X44-36B00$737.mif
V2
36B
POWER – ASSISTED STEERING
Fault finding – Parameter summary table
Tool parameter Diagnostic tool title
PR001Torque applied to the steering wheel
PR003Vehicle speed
PR004Engine speed
PR121Steering wheel angle
PR129Motor power (60 A)
PR130Motor power (45 A)
PR131Current setpoint (60 A)
PR132Current setpoint (45 A)
EPAS
Vdiag No.: 04 - 08
MR-413-X44-36B00$737.mif

36B-36
MR-413-X44-36B000$804.mif
V2
36B
POWER – ASSISTED STEERING
Fault finding – Interpretation of parameters
PR001
TORQUE APPLIED TO THE STEERING WHEEL
NOTESNone.
This parameter indicates the torque applied by the driver to the steering column.
If the parameter does not conform with the values indicated in the Conformity check, consult the interpretation of
fault DF054 Torque sensor.
AFTER REPAIRPerform a test using the diagnostic tool.
DAE_V04_PR001/DAE_V08_PR001
EPAS
Vdiag No.: 04 - 08
MR-413-X44-36B000$804.mif

36B-40
MR-413-X44-36B000$804.mif
V2
POWER – ASSISTED STEERING
Fault finding – Interpretation of parameters
EPAS
Vdiag No.: 04 - 08
36B
PR129
PR131
MOTOR POWER (60 A)
CURRENT SETPOINT (60 A)
NOTESNone.
Parameter PR131 Current setpoint (60 A) indicates the current setpoint (power) sent by the EPAS computer to
the steering motor according to the torque applied to the steering wheel. Parameter PR129 Motor power (60 A)
indicates the electric current actually consumed by the EPAS motor.
The value of parameter PR131 Current setpoint (60 A) must be approximately equal to the value of parameter
PR129 Motor power (60 A).
If the parameters are not the same, contact the Techline.
AFTER REPAIRPerform a test using the diagnostic tool.
DAE_V04_PR129/DAE_V04_PR131/ DAE_V08_PR129/DAE_V08_PR131

36B-41
MR-413-X44-36B000$804.mif
V2
POWER – ASSISTED STEERING
Fault finding – Interpretation of parameters
EPAS
Vdiag No.: 04 - 08
36B
PR130
PR132
MOTOR POWER (45 A)
CURRENT SETPOINT (45 A)
NOTESNone.
Parameter PR130 Current setpoint (45 A) indicates the current setpoint (power) sent by the EPAS computer to
the steering motor according to the torque applied to the steering wheel. Parameter PR132 Motor power (45 A)
indicates the electric current actually consumed by the EPAS motor.
The value of parameter PR130 Current setpoint (45 A) must be approximately equal to the value of parameter
PR132 Motor power (45 A).
If the parameters are not the same, contact the Techline.
AFTER REPAIRPerform a test using the diagnostic tool.
DAE_V04_PR130/DAE_V04_PR132/ DAE_V08_PR130/DAE_V08_PR132

36B-51
MR-413-X44-36B000$938.mif
V2
POWER – ASSISTED STEERING
Fault finding – Fault finding Chart
EPAS
Vdiag No.: 04 - 08
36B
ALP 9 STEERING WHEEL VIBRATION OR PULSATING
NOTESOnly address this customer complaint after a complete check with the diagnostic
tool.
Use the Technical Note wiring diagram for New Twingo.
Connectors of component 502 disconnected, check the condition and conformity of the connectors and clips.
If the connector is faulty (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for
repair), repair the connector, otherwise replace the wiring.
With the connector of component 1016 disconnected:
Check the continuity and insulation of connection AP23 between components 502 and 1016.
Check the continuity and insulation of connection ML of component 502.
If the connection or connections are faulty (see Technical Note 6015A, Repairing electrical wiring, Wiring:
Precautions for repair), repair the wiring, otherwise replace it.
If the checks reveal no faults, perform a conformity check of component 1016.
Check the conformity of PR001 Torque applied to steering wheel (see Conformity check).
If the value of this parameter changes drastically without any movement of the steering wheel, contact the
Techline
Check the conformity of PR129 Motor power (60 A) or PR130 Motor power (45 A) (see Conformity check).
If the value of this parameter changes drastically without any movement of the steering wheel, contact the
Techline.
If the incident is still present, contact the Techline.
AFTER REPAIRPerform a check using the diagnostic tool.
DAE_V04_ALP9/ DAE_V08_ALP9