2009 RENAULT TWINGO ESP

38C-33
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool
If the fault is still present, contact the Techline.
V3 MR-413-X44-38C050$101.mif
ANTI-LOCK BRAKING SYSTEM
Fault finding – Interpretation of faults38C
Bosch 8.1 ESP
Vdiag No.: 05
DF027
CONTINUED
2.DEFNOTESConditions for applying the fault finding procedure to
stored faults:
The fault is declared present after a road test.
Check the connection and condition (possible wiring damage) of the connectors ofcomponents 1 094and150.
Iftheconnector is faulty (seeTe chnical Note 6015A, Repairing e lectrical wiring, Wiring: Precautions for repair),
repair the connector, otherwise replace the wiring.
Ch eck the insulation and continuity ofconnections 4Sand4Tbetweencomponents 150and1094.
Alsocheckthe insulationbetween these 2 connections.
Iftheconnection or connections are faulty (seeTe chnical Note 6015A, Repairing e lectrical wiring, Wiring:
Precautions for repair), repair the wiring, otherwise replace it.
Inspect the condition of the target ( metallic contamination etc.).
Cleanthetarget with compressed air if necessary.
For v ersions e quippedwithdiscbrakes:
Check the sensor/target air gap through one wheel revolution (0.1 mm If the air gap isincorrect:
–Replace the instrumented bearing/wheel sensor mounting assembly (see MR 411, Mechanical, 33A, Rear axle
components, Rear hub carrier bearing: Removal - Refitting).
If the air gap iscorrect:
–Swap both rear wheel brake discs as well as the brake pads.
–Clear the computer fault memory.
–Carry out a road test followed by another check with the diagnostic tool.
–If the fault initially declared as DF007 Rear left-hand wheel speed sensor circuit has become DF027, replace
the instrumented bearing/wheel sensor mounting assembly (see MR 411, Mechanical, 33A, Rear axle
components, Rear hub carrier bearing: Removal - Refitting).
–If the fault remains on the same side, replace component 150 (see MR 411, Mechanical, 38C, Anti-lock
braking system, Rear wheel speed sensor, Removal - Refitting).
For v ersions e quippedwithdrumbrakes:
–Swap both rear wheel brake drums.
–Clear the computer fault memory.
–Carry out a road test followed by another check with the diagnostic tool.
–If the fault initially declared as DF007 Rear left-hand wheel speed sensor circuit has become DF027, replace
the target (see MR 411, Mechanical, 33A, Rear axle components, Rear brake drums, Removal - Refitting).
–If the fault remains on the same side, replace component 150 (see MR 411, Mechanical, 38C, Anti-lock
braking system, Rear wheel speed sensor, Removal - Refitting).

38C-34
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool
If the fault is still present, contact the Techline.
V3 MR-413-X44-38C050$101.mif
ANTI-LOCK BRAKING SYSTEM
Fault finding – Interpretation of faults38C
Bosch 8.1 ESP
Vdiag No.: 05
DF055
PRESENTVEHICLE PARAMETER PROGRAMMINGDEF: configuration absent or incorrect
NOTESNone.
Configure the vehicle parameters using command VP004 Vehicle parameters (see help table in clip).
Clear the fault memory, and initialise the computer (switch the + after ignition feed off and on again).
Check for any possible faults.
ESP_V05_DF055

38C-35
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool
If the fault is still present, contact the Techline.
V3 MR-413-X44-38C050$101.mif
ANTI-LOCK BRAKING SYSTEM
Fault finding – Interpretation of faults38C
Bosch 8.1 ESP
Vdiag No.: 05
DF063
PRESENT
OR
STOREDWHEEL SPEED CONSISTENCY
DEF: inconsistency
CC.1: short-circuit to +12 volts
NOTESSpecial notes:
This fault indicates that the wheel speeds are inconsistent with each other.
The computer does not know how to determine which one is faulty.
Priorities when dealing with a number of faults:
Deal first with faults DF090 Front right-hand wheel target, DF091 Front left-hand
wheel target, DF092 Rear right-hand wheel target and DF093 Rear left-hand wheel
target even if they are stored.
Use the Wiring Diagram Technical Note for New Twingo.
DEF
NOTESConditions for applying the fault finding procedure to
stored faults:
The fault is declared present after a road test.
Check the quality of the mounting of the wheel speed sensors (correct clipping without excessive play).
Check the conformity of the targets (condition, number of teeth = 48) using the specific command SC001 Check
target teeth for each wheel.
Are the numbers of teeth correct?
YESVisually inspect the condition of the axles (impacts, deformations, etc.) and check that
the tyre mountings conform and are in good condition (see MR 411, Mechanical, 35A,
Wheels and tyres, Identification).
Ensure that the braking system is in good condition (condition of the linings, tightness,
grip, bleeding, bearing play, lubricant on the targets, etc.).
NOApply the target fault procedure for the wheel(s) concerned:
–DF090 Front right-hand wheel target
–DF091 Front left-hand wheel target
–DF092 Rear right-hand wheel target
–DF093 Rear left-hand wheel target
ESP_V05_DF063

38C-36
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool
If the fault is still present, contact the Techline.
V3 MR-413-X44-38C050$101.mif
ANTI-LOCK BRAKING SYSTEM
Fault finding – Interpretation of faults38C
Bosch 8.1 ESP
Vdiag No.: 05
DF063
CONTINUED
2.DEFNOTESNone.
Check the connection and condition (possible wiring damage) of the connectors:
–of component 1094,
–of component 150,
–of component 151,
–of component 152,
–of component 153.
Iftheconnector is faulty (seeTe chnical Note 6015A, Repairing e lectrical wiring, Wiring: Precautions for repair),
repair the connector, otherwise replace the wiring.
Ch eckthe insulation and continuityofconnections 4Mand4Nbetweencomponents 152and1094.
Alsocheckthe insulationbetween these 2 connections.
Ch eckthe insulation and continuityofconnections 4Sand4Tbetweencomponents 1 50and1094.
Alsocheckthe insulationbetween these 2 connections.
Ch eckthe insulation and continuityofconnections 4Cand4Ebetweencomponents 1 53and1094.
Alsocheckthe insulationbetween these 2 connections.
Ch eckthe insulation and continuityofconnections 4Gand4Hbetweencomponents 151and1094.
Alsocheckthe insulationbetween these 2 connections.
If theconnection(s) are faulty (seeTechnical Note 6 015A, Electrical wiring repair, Wiring: Precautions for repair),
repair the wiring, otherwise replace the wiring.
Perform the procedure of counting the poles for each wheel (number of teeth =48)usingspecial command
SC001 Check target teethtoconfirm the disappearance of the fault.

38C-37
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool
If the fault is still present, contact the Techline.
V3 MR-413-X44-38C050$101.mif
ANTI-LOCK BRAKING SYSTEM
Fault finding – Interpretation of faults38C
Bosch 8.1 ESP
Vdiag No.: 05
DF066
PRESENT
OR
STOREDINJECTION MULTIPLEX SIGNAL ABSENT
NOTESSpecial notes:
The injection does not always store these transient faults as quickly as the ESP
system.
If no fault is stored in the injection computer, start the engine; if there is no fault present,
contact the Techline.
Once the fault in the injection system has been repaired, clear the ESP computer
fault memory.
Priority in the event of a number of faults:
Deal with fault DF152 Multiplex network first if it is present or stored.
Conditions for applying the fault finding procedure to stored faults:
The fault is declared present when the engine is started.
Check the injection computer (see13B, Diesel injection or 17B, Petrol injection)usingthe diagnostic tool.
Ru n a m ultiple xnetwork test (see88B, Multiplex).
ESP_V05_DF066

38C-38
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool
If the fault is still present, contact the Techline.
V3 MR-413-X44-38C050$101.mif
ANTI-LOCK BRAKING SYSTEM
Fault finding – Interpretation of faults38C
Bosch 8.1 ESP
Vdiag No.: 05
DF075
PRESENT
OR
STOREDSTEERING WHEEL ANGLE SENSOR SIGNAL
1. DEF: inconsistency
2. DEF: constant signal
NOTESConditions for applying the fault finding procedure to stored faults:
The fault is declared present after a road test.
1.DEF
NOTESSpecial notes:
Question the customer to find out if he regularly drives on
a speed track. If this is the case, follow the procedure below
but never replace component 583.
Clear the ESP offsets using command RZ011 Sensor offset.
Position the steering wheel straight ahead (the wheels must be directly in line with the vehicle) and read the value
of the steering wheel angle using the parameter PR033 "Steering wheel angle".
If the value is not close to 0 ± 5˚, calibrate component 583 using command VP003 Steering wheel angle sensor
(see Configurations and programming).
Clear the ESP sensor offsets using command RZ011 Sensor offset.
With the steering wheel horizontal and the front wheels set straight ahead, turn the steering wheel a quarter of
a turn to the left.
Using parameter PR033 Steering wheel angle, check that the steering wheel angle value is close to - 90.
With the steering wheel horizontal and the front wheels set straight ahead, turn the steering wheel a quarter of
a turn to the right.
Using parameter PR033 Steering wheel angle, check that the steering wheel angle value is close to + 90.
If the steering wheel angle values are not correct, replace component 583 (see MR 411, Mechanical, 36A,
Steering assembly, Steering column, Removal - Refitting).
Drive in a straight line.
If the steering wheel is not horizontal when the vehicle is driving in a straight line (the vehicle "pulls" to the left
or right):
Check the conformity of the tyres, pressures, wear and dimensions (see MR 411, 35A, Wheels and tyres, Tyres,
Identification and tyre pressure, Identification).
Replace the tyre(s) if necessary (see MR 411, 35A, Wheels and tyres, Tyres, Removal - Refitting).
Adjust the wheel alignment (see MR 411, Mechanical, 30A, General information, Front axle: Adjustment).
Calibrate component 583 using command VP003 Steering wheel angle sensor (see Configurations
and programming).
Clear the ESP sensor offsets using command RZ011 Sensor offsets.
ESP_V05_DF075

38C-39
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool
If the fault is still present, contact the Techline.
V3 MR-413-X44-38C050$101.mif
ANTI-LOCK BRAKING SYSTEM
Fault finding – Interpretation of faults38C
Bosch 8.1 ESP
Vdiag No.: 05
DF075
CONTINUED
2.DEFNOTESNone.
Clear the ESP offsets using command RZ011 Sensor offset.
When stationary, turn the steering wheel from left to right and check that the value changes using parameter PR033
Steering wheel angle.
If the value is inconsistent, replace component 583 (see MR 411, Mechanical, 36A, Steering assembly,
Steering column, Removal - Refitting).

38C-40
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool
If the fault is still present, contact the Techline.
V3 MR-413-X44-38C050$101.mif
ANTI-LOCK BRAKING SYSTEM
Fault finding – Interpretation of faults38C
Bosch 8.1 ESP
Vdiag No.: 05
DF086
PRESENT
OR
STOREDCOMPUTER CONFIGURATION
DEF: incorrect vehicle configuration
NOTESNone.
Configure the inhibition or authorisation of the automatic brake lights (according to the legislation of the country).
Using command VP021 Automatic brake light inhibition:
Configure the inhibition of the automatic brake lights using command VP021 Automatic brake light inhibition
Using command VP022 Automatic brake light authorisation:
Configure the authorisation of the automatic brake lights using command VP022 Automatic brake light
authorisation.
ESP_V05_DF086