2009 RENAULT TWINGO air condition

38C-28
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool
If the fault is still present, contact the Techline.
V3 MR-413-X44-38C050$101.mif
ANTI-LOCK BRAKING SYSTEM
Fault finding – Interpretation of faults38C
Bosch 8.1 ESP
Vdiag No.: 05
DF017
PRESENT
OR
STOREDCOMPUTER
1. DEF: Supply fault or internal electronic fault
NOTESConditions for applying the fault finding procedure to stored faults:
Apply the fault finding procedure whether the fault is present or stored.
Use the Wiring Diagram Technical Note for New Twingo.
Check the tightness and condition of the battery terminals (see 80A, Battery).
Check the charging circuit (see 16A, Starting - Charging).
Check the condition and position of fuses F1 and F2 (40A and 30A) in the engine fuse box and fuse F10 (5A) in
the passenger compartment fuse box (see MR413, Fault finding, 81C, Fuse box).
Check the connection and condition (possible wiring damage) of the connector of component 1094.
If the connector is faulty (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions
for repair), repair the connector, otherwise replace the wiring.
With the connector of component 1094 disconnected, check the insulation and continuity of connections MAH
of component 1094 (tightness, oxidation etc.).
With the connectors of component 1094, 1175, 583 and intermediate connector R107 disconnected, check
the insulation and continuity of connection AP5 between component 1094 and intermediate connector R107.
Check the insulation and continuity of connection AP5 between intermediate connector R107 and
component 1016.
With the connectors of components 1094 and 1834 disconnected, check the continuity and insulation
of connection BP14 between components 1094 and 1834.
With the connectors of components 1094 and 1834 disconnected, check the continuity and insulation
of connection BP8 between components 1094 and 1834.
If the connection(s) are faulty (see Technical Note 6015A, Electrical wiring repair, Wiring: Precautions
for repair), repair the wiring, otherwise replace the wiring.
ESP_V05_DF017

38C-30
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool
If the fault is still present, contact the Techline.
V3 MR-413-X44-38C050$101.mif
ANTI-LOCK BRAKING SYSTEM
Fault finding – Interpretation of faults38C
Bosch 8.1 ESP
Vdiag No.: 05
DF026
PRESENT
OR
STOREDFRONT RIGHT-HAND WHEEL SPEED SENSOR CIRCUITCO.0: open circuit or short circuit to earth
CO.1: open circuit or short circuit to +12 V
1. DEF: internal electronic fault
2. DEF: magnetic or mechanical fault on the target or interference
NOTESUse the Wiring Diagram Technical Note for New Twingo.
CO.0
CO.1
1.DEF
NOTESNone.
Check the connection and condition (possible wiring damage) of the connectors of components 1094 and 152.
If the connector is faulty (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions
for repair), repair the connector, otherwise replace the wiring.
Swap the 2 front wheel speed sensors (see MR 411 Mechanical, 38C, Wheel speed sensor, Removal -
Refitting).
Clear the computer fault memory.
Switch off the ignition.
Switch on the ignition again.
Did the fault initially declared as DF026 become fault DF006 "Front left-hand wheel speed sensor circuit"
present?
YESReplace the wheel speed sensor (see MR 411 Mechanical, 38C, Anti-lock braking
system, Front wheel speed sensor, Removal - Refitting).
NOCheck the insulation and continuity of connections 4M and 4N between
components 152 and 1094.
Also check the insulation between these 2 connections.
If the connection or connections are faulty (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the wiring, otherwise
replace it.
If all the checks are in order, contact Techline.
ESP_V05_DF026

38C-31
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool
If the fault is still present, contact the Techline.
V3 MR-413-X44-38C050$101.mif
ANTI-LOCK BRAKING SYSTEM
Fault finding – Interpretation of faults38C
Bosch 8.1 ESP
Vdiag No.: 05
DF026
CONTINUED
2.DEFNOTESConditions for applying the fault finding procedure to
stored faults:
The fault is declared present after a road test.
Check the connection and condition (possible wiring damage) of the connectors ofcomponents 1 094and152.
Iftheconnector is faulty (seeTe chnical Note 6015A, Repairing e lectrical wiring, Wiring: Precautions for repair),
repair the connector, otherwise replace the wiring.
Swap the 2 front wheel speed sensors (seeMR 411 M echanical, 38C, W heel speed sensor, Removal - Refitting).
Clearthecomputer fault memory.
Switch offtheignition.
Switch on the ignit io nagain.
Carry out a road test.
Did the fault i nitially declared asDF0 26becomeDF006 "Front left-hand wheel speed sensor circuit" present?
YESReplace component 152 (see MR 411, Mechanical, 38C, Anti-lock braking system,
Front wheel speed sensor, Removal - Refitting).
NOCh eckthe insulatio n a nd c on t i n ui t yof connections4Mand4Nbetween components
152and1094.
Alsocheckthe insulationbetween these 2 connections.
Iftheconnection or connections are faulty (seeTe chnical Note 6 015A, Repairing
electrical wiring, W iring: Precautions for repair), repair the wiring, otherwise replace it.
Inspect the condition of the target (metallic contamination etc.).
Cle an the target with compressed air if necessary.
Ch eck the sensor / target air gap through one wheel revolution (0.4 gap <1.7 mm).
If the air gap isincorrect:
–Replace the instrumented bearing/wheel sensor mounting assembly (see MR 411,
Mechanical, 31A, Front axle components, Front hub carrier bearing: Removal
– Refitting).
If the air gap iscorrect:
–After cleaning the target, clear the computer fault memory.
–Carry out a road test followed by another check with the diagnostic tool.
–If the fault is still present, replace the instrumented bearing/wheel sensor mounting
assembly (see MR 411 Mechanical, 31A, Front axle components, Front hub
carrier bearing: Removal – Refitting).

38C-32
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool
If the fault is still present, contact the Techline.
V3 MR-413-X44-38C050$101.mif
ANTI-LOCK BRAKING SYSTEM
Fault finding – Interpretation of faults38C
Bosch 8.1 ESP
Vdiag No.: 05
DF027
PRESENT
OR
STOREDREAR RIGHT-HAND WHEEL SPEED SENSOR CIRCUITCO.0: open circuit or short circuit to earth
CO.1: open circuit or short circuit to +12 V
1. DEF: internal electronic fault
2. DEF: magnetic or mechanical fault on the target or interference
NOTESUse the Wiring Diagram Technical Note for New Twingo.
CO.0
CO.1
1.DEF
NOTESNone.
Check the connection and condition (possible wiring damage) of the connectors of components 1094 and 150.
If the connector is faulty (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions
for repair), repair the connector, otherwise replace the wiring.
Using command AC013 Wheel speed sensor supply test (see Interpretation of commands), check for
a voltage of approximately 12 V between connections 4S and 4T of the component.
Is the voltage measured correct?
YESReplace component 150 (see MR 411, Mechanical, 38C, Anti-lock braking system,
Rear wheel speed sensor, Removal - Refitting).
NOCheck the insulation and continuity of connections 4S and 4T between
components 150 and 1094.
Also check the insulation between these 2 connections.
If the connection or connections are faulty (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace
the wiring.
If all the checks are in order, contact Techline.
ESP_V05_DF027

38C-33
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool
If the fault is still present, contact the Techline.
V3 MR-413-X44-38C050$101.mif
ANTI-LOCK BRAKING SYSTEM
Fault finding – Interpretation of faults38C
Bosch 8.1 ESP
Vdiag No.: 05
DF027
CONTINUED
2.DEFNOTESConditions for applying the fault finding procedure to
stored faults:
The fault is declared present after a road test.
Check the connection and condition (possible wiring damage) of the connectors ofcomponents 1 094and150.
Iftheconnector is faulty (seeTe chnical Note 6015A, Repairing e lectrical wiring, Wiring: Precautions for repair),
repair the connector, otherwise replace the wiring.
Ch eck the insulation and continuity ofconnections 4Sand4Tbetweencomponents 150and1094.
Alsocheckthe insulationbetween these 2 connections.
Iftheconnection or connections are faulty (seeTe chnical Note 6015A, Repairing e lectrical wiring, Wiring:
Precautions for repair), repair the wiring, otherwise replace it.
Inspect the condition of the target ( metallic contamination etc.).
Cleanthetarget with compressed air if necessary.
For v ersions e quippedwithdiscbrakes:
Check the sensor/target air gap through one wheel revolution (0.1 mm If the air gap isincorrect:
–Replace the instrumented bearing/wheel sensor mounting assembly (see MR 411, Mechanical, 33A, Rear axle
components, Rear hub carrier bearing: Removal - Refitting).
If the air gap iscorrect:
–Swap both rear wheel brake discs as well as the brake pads.
–Clear the computer fault memory.
–Carry out a road test followed by another check with the diagnostic tool.
–If the fault initially declared as DF007 Rear left-hand wheel speed sensor circuit has become DF027, replace
the instrumented bearing/wheel sensor mounting assembly (see MR 411, Mechanical, 33A, Rear axle
components, Rear hub carrier bearing: Removal - Refitting).
–If the fault remains on the same side, replace component 150 (see MR 411, Mechanical, 38C, Anti-lock
braking system, Rear wheel speed sensor, Removal - Refitting).
For v ersions e quippedwithdrumbrakes:
–Swap both rear wheel brake drums.
–Clear the computer fault memory.
–Carry out a road test followed by another check with the diagnostic tool.
–If the fault initially declared as DF007 Rear left-hand wheel speed sensor circuit has become DF027, replace
the target (see MR 411, Mechanical, 33A, Rear axle components, Rear brake drums, Removal - Refitting).
–If the fault remains on the same side, replace component 150 (see MR 411, Mechanical, 38C, Anti-lock
braking system, Rear wheel speed sensor, Removal - Refitting).

38C-35
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool
If the fault is still present, contact the Techline.
V3 MR-413-X44-38C050$101.mif
ANTI-LOCK BRAKING SYSTEM
Fault finding – Interpretation of faults38C
Bosch 8.1 ESP
Vdiag No.: 05
DF063
PRESENT
OR
STOREDWHEEL SPEED CONSISTENCY
DEF: inconsistency
CC.1: short-circuit to +12 volts
NOTESSpecial notes:
This fault indicates that the wheel speeds are inconsistent with each other.
The computer does not know how to determine which one is faulty.
Priorities when dealing with a number of faults:
Deal first with faults DF090 Front right-hand wheel target, DF091 Front left-hand
wheel target, DF092 Rear right-hand wheel target and DF093 Rear left-hand wheel
target even if they are stored.
Use the Wiring Diagram Technical Note for New Twingo.
DEF
NOTESConditions for applying the fault finding procedure to
stored faults:
The fault is declared present after a road test.
Check the quality of the mounting of the wheel speed sensors (correct clipping without excessive play).
Check the conformity of the targets (condition, number of teeth = 48) using the specific command SC001 Check
target teeth for each wheel.
Are the numbers of teeth correct?
YESVisually inspect the condition of the axles (impacts, deformations, etc.) and check that
the tyre mountings conform and are in good condition (see MR 411, Mechanical, 35A,
Wheels and tyres, Identification).
Ensure that the braking system is in good condition (condition of the linings, tightness,
grip, bleeding, bearing play, lubricant on the targets, etc.).
NOApply the target fault procedure for the wheel(s) concerned:
–DF090 Front right-hand wheel target
–DF091 Front left-hand wheel target
–DF092 Rear right-hand wheel target
–DF093 Rear left-hand wheel target
ESP_V05_DF063

38C-36
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool
If the fault is still present, contact the Techline.
V3 MR-413-X44-38C050$101.mif
ANTI-LOCK BRAKING SYSTEM
Fault finding – Interpretation of faults38C
Bosch 8.1 ESP
Vdiag No.: 05
DF063
CONTINUED
2.DEFNOTESNone.
Check the connection and condition (possible wiring damage) of the connectors:
–of component 1094,
–of component 150,
–of component 151,
–of component 152,
–of component 153.
Iftheconnector is faulty (seeTe chnical Note 6015A, Repairing e lectrical wiring, Wiring: Precautions for repair),
repair the connector, otherwise replace the wiring.
Ch eckthe insulation and continuityofconnections 4Mand4Nbetweencomponents 152and1094.
Alsocheckthe insulationbetween these 2 connections.
Ch eckthe insulation and continuityofconnections 4Sand4Tbetweencomponents 1 50and1094.
Alsocheckthe insulationbetween these 2 connections.
Ch eckthe insulation and continuityofconnections 4Cand4Ebetweencomponents 1 53and1094.
Alsocheckthe insulationbetween these 2 connections.
Ch eckthe insulation and continuityofconnections 4Gand4Hbetweencomponents 151and1094.
Alsocheckthe insulationbetween these 2 connections.
If theconnection(s) are faulty (seeTechnical Note 6 015A, Electrical wiring repair, Wiring: Precautions for repair),
repair the wiring, otherwise replace the wiring.
Perform the procedure of counting the poles for each wheel (number of teeth =48)usingspecial command
SC001 Check target teethtoconfirm the disappearance of the fault.

38C-37
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool
If the fault is still present, contact the Techline.
V3 MR-413-X44-38C050$101.mif
ANTI-LOCK BRAKING SYSTEM
Fault finding – Interpretation of faults38C
Bosch 8.1 ESP
Vdiag No.: 05
DF066
PRESENT
OR
STOREDINJECTION MULTIPLEX SIGNAL ABSENT
NOTESSpecial notes:
The injection does not always store these transient faults as quickly as the ESP
system.
If no fault is stored in the injection computer, start the engine; if there is no fault present,
contact the Techline.
Once the fault in the injection system has been repaired, clear the ESP computer
fault memory.
Priority in the event of a number of faults:
Deal with fault DF152 Multiplex network first if it is present or stored.
Conditions for applying the fault finding procedure to stored faults:
The fault is declared present when the engine is started.
Check the injection computer (see13B, Diesel injection or 17B, Petrol injection)usingthe diagnostic tool.
Ru n a m ultiple xnetwork test (see88B, Multiplex).
ESP_V05_DF066