2009 RENAULT TWINGO ABS

38C-52
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool
If the fault is still present, contact the Techline.
V3 MR-413-X44-38C050$101.mif
ANTI-LOCK BRAKING SYSTEM
Fault finding – Interpretation of faults38C
Bosch 8.1 ESP
Vdiag No.: 05
DF126
PRESENT
OR
STOREDCOMBINED SENSOR SIGNAL PLAUSIBILITY
NOTESSpecial notes:
If the fault appears while the vehicle is being driven on a steep gradient, during a very
tight turn or while the vehicle is being transported on a lorry, train, boat etc., with the
engine running, clear the fault and test drive, if possible, to check that the fault does
not return.
Conditions for applying fault finding procedures to stored faults:
The fault is declared present after a road test.
Check that component 1175 is fitted and attached correctly (the arrow indicating the front of the vehicle).
Check the conformity of the tyres (see MR 411, Mechanical, 35A, Wheels and tyres, Tyres: Identification
and Tyre pressure, Identification).
Check the axle assembly geometry (see MR 411, Mechanical, Chassis, Front axle adjustment).
Calibrate component 583 using command VP003 Steering wheel angle sensor (see Configurations
and programming).
Clear the ESP sensor offsets using command RZ011 Sensor offset.
Re-establish dialogue with the ABS/ESP computer, and if no other fault is to be dealt with, clear the computer fault
memory.
Carry out a road test.
If the fault is still present, contact the Techline.
ESP_V05_DF126

38C-58
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool
If the fault is still present, contact the Techline.
V3 MR-413-X44-38C050$102.mif
38C
Bosch 8.1 ESP
Vdiag No.: 05
DF188
PRESENT
OR
STOREDBRAKE LIGHT SWITCH CIRCUIT
1.DEF: Inconsistency
2.DEF: Permanent high signal
NOTESConditions for applying the fault finding procedure to stored faults:
Clear the stored fault, carry out a road test at a speed of > 36 mph (60 km/h) and test
the brakes using ABS.
Use the interpretation of the fault if it recurs.
Special notes:
The fault is detected if the computer does not detect a brake lights switch status change
for 4 acceleration/braking cycles and/or the contact is closed for over 6 minutes with
the vehicle speed above 24 mph (40 km/h).
Using the diagnostic tool, check on the status screen that ET017 Brake pedal recognises the correct pressed
and released positions of the brake pedal.
If the correct pedal position is not displayed, use the interpretation of ET017 Brake pedal.
ANTI-LOCK BRAKING SYSTEM
Fault finding – Interpretation of faults
ESP_V05_DF188

38C-63
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool
If the fault is still present, contact the Techline.
V3 MR-413-X44-38C050$102.mif
ANTI-LOCK BRAKING SYSTEM
Fault finding – Interpretation of faults38C
Bosch 8.1 ESP
Vdiag No.: 05
DF193
PRESENT
OR
STOREDINJ. MULTIPLEX SIGNALS INVALID
NOTESSpecial notes:
Even though it is stored in the computer, the ABS/ESP system is not faulty.
The ESP is deactivated following unusable information from the injection system.
Perform fault finding on the injection system using the diagnostic tool.
Note:
The injection does not always store these transient faults as quickly as the ABS/ESP.
Note:
Once the fault in the injection system has been repaired, clear the ABS/ESP computer
fault memory.
Conditions for applying the fault finding procedure to stored faults:
The fault is declared present when the engine is started.
Check the injection computer (see 13B, Diesel injection or 17B, Petrol injection) using the diagnostic tool.
Run a multiplex network test (see 88B, Multiplex).
ESP_V05_DF193

38C-68
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool
If the fault is still present, contact the Techline.
V3 MR-413-X44-38C050$102.mif
ANTI-LOCK BRAKING SYSTEM
Fault finding – Interpretation of faults38C
Bosch 8.1 ESP
Vdiag No.: 05
DF313
PRESENT
OR
STOREDINVALID SEQUENTIAL GEARBOX MULTIPLEX SIGNALS
NOTESSpecial notes:
The ABS/ESP system is not faulty, but has received unusable signals from the BVR.
Perform fault finding on the BVR using the diagnostic tool.
Note:
Once the fault in the sequential gearbox system has been repaired, clear the ABS/ESP
computer fault memory.
Conditions for applying the fault finding procedure to stored faults:
The fault is declared present when the engine is started.
Run a check on the BVR using the diagnostic tool (see 21B, Sequential gearbox).
Run a multiplex network test (see 88B, Multiplex).
ESP_V05_DF313

38C-69
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool
If the fault is still present, contact the Techline.
V3 MR-413-X44-38C050$102.mif
ANTI-LOCK BRAKING SYSTEM
Fault finding – Interpretation of faults38C
Bosch 8.1 ESP
Vdiag No.: 05
DF321
PRESENT
OR
STOREDCLUTCH SWITCH SIGNAL CONSISTENCY
DEF: Inoperative
NOTESSpecial notes:
The ABS/ESP system is not faulty.
Perform fault finding on the injection system using the diagnostic tool.
Note:
Once the fault in the INJECTION system has been repaired, clear the ABS/ESP
computer fault memory.
Conditions for applying the fault finding procedure to stored faults:
The fault is declared present when driving after having exceeded a speed of 42 mph
(70 km/h).
Check the injection computer (see 13B, Diesel injection or 17B, Petrol injection) using the diagnostic tool.
ESP_V05_DF321

38C-78
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V3 MR-413-X44-38C050$150.mif
38C
Bosch 8.1 ESP
Vdiag No.: 05
Tool command Diagnostic tool title Comments
RZ001Fault memory This command is used for clearing the computer's stored faults
RZ011Sensor offsetsThis command reinitialises programming of the ESP sensors.
Run this command each time an operation required the steering
wheel angle to be programmed or following any operation on the
axle assemblies.
Also run this command when the combined sensor has been
removed or replaced
SC001Check target teethThis command tests the condition of the teeth on each wheel.
Select the command SC001 and follow the instructions.
The test result should indicate 48 teeth.
SC006Bleed the hydraulic unit and
brake circuitsThis command should only be used if an abnormally long brake
pedal travel is noted during a road test with ABS control (the
system must have been bled beforehand by the usual method).
Select command SC006 and follow the instructions given by the
diagnostic tool.
AC003Front left-hand wheel solenoid
valvesSee the interpretation of command (see Interpretation of
commands).
AC004Front right-hand wheel
solenoid valvesSee the interpretation of command (see Interpretation of
commands).
AC005Rear left-hand wheel solenoid
valvesSee the interpretation of command (see Interpretation of
commands).
AC006Rear right-hand wheel solenoid
valvesSee the interpretation of command (see Interpretation of
commands).
AC013Wheel speed sensor supply
testSee the interpretation of command (see Interpretation of
commands).
AC016Pump motor testSee the interpretation of command (see Interpretation of
commands).
AC187Brake light activation relaySee the interpretation of command (see Interpretation of
commands).
AC195Vehicle speed signalSee the interpretation of command (see Interpretation of
commands).
AC196Hazard warning light activation
requestSee the interpretation of command (see Interpretation of
commands).
ANTI-LOCK BRAKING SYSTEM
Fault finding – Command summary table

38C-85V3 MR-413-X44-38C050$170.mif
38C
Bosch 8.1 ESP
Vdiag No.: 05
NOTESOnly check the customer complaint after performing a full check with the
diagnostic tool.
FAULTS DETECTED ON BRAKING WITH ABS/BRAKING REGULATION
Locking of one or more wheels ALP2
PullALP3
DriftALP4
Unexpected ABS operation at low speed and with slight pedal pressure ALP5
Unexpected ABS operation on a poor road surface ALP6
Unexpected ABS operation when using special equipment (car phone, CB, etc.) ALP7
Lengthening of the brake pedal travel following a regulation phase (with an
irregular pedal when entering the regulation phase)ALP8
Spongy pedalALP9
Brake pedal vibrationALP10
Noises from the pump, the pipes or the hydraulic unit ALP11
ANTI-LOCK BRAKING SYSTEM
Fault finding – Customer complaints

38C-86V3 MR-413-X44-38C050$170.mif
ANTI-LOCK BRAKING SYSTEM
Fault finding – Customer complaints38C
Bosch 8.1 ESP
Vdiag No.: 05
OTHER CASES
No dialogue with the ABS computer ALP1
ESP computer not detected during the multiplex network test on CLIP ALP12
Illumination of brake lights ALP 13
Unexpected ABS operation at low speeds and slight pedal pressure ALP14
Intermittent illumination of brake, ESP, ABS, SERVICE and STOP warning lights
and the message "Brake failure" on the instrument panel with no fault codes in
the computerALP15