2009 RENAULT SCENIC fuel pressure

DIESEL INJECTION
Fault finding – Interpretation of faults13B
13B-79V3 MR-372-J84-13B250$360.mif
EDC16
PROGRAM No.: C1
Vdiag No.: 51
DF053
CONTINUED 1
CC.0
CO
NOTESNone
Measure the resistance of the rail pressure regulator between tracks 1 and 2.
If the resistance is not 3 ± 1 Ω at 20˚C, replace the injection pump.
Check the continuity and insulation from the + 12 V feed of the following connection:
Injection computer brown 48-track
connector B, track M4Track 2 of the rail pressure regulator (fuel flow actuator)
Check the rail pressure sensor using the interpretation of DF007 Rail pressure sensor circuit.
If the fault is still present, replace the injection pump.
Check the rail pressure regulator connectors.
Check the injection computer connections.
Check the low pressure circuit by applying test 2 Low pressure circuit check.
Check the conformity of the fuel used by applying test 10 Diesel fuel conformity check.
Check the injector return flow, run test 8 Poor injector operation.
Check the operation of the overpressure valve if fitted to the vehicle, run test 11 Incorrect operation of the
overpressure valve.
Repair if necessary.
Measure the resistance of the rail pressure regulator between tracks 1 and 2.
If the resistance is not 3 ± 1 Ω at 20˚C, replace the injection pump.
Check the continuity, and insulation from earth of the following connection:
Injection computer brown 48-track
connector B, track M4Track 2 of the rail pressure regulator (fuel flow actuator)
With the ignition on, check for + 12 V after relay on track 1 of the rail pressure regulator.
If there is not + 12 V on track 1, check the continuity and absence of interference resistance of the following
connection:
Rail pressure regulator track 1Injection supply relay mounting track 5
Repair if necessary.
Check the rail pressure sensor using the interpretation of DF007 Rail pressure sensor circuit.
If the fault is still present, replace the injection pump.
AFTER REPAIRDeal with any faults.
Carry out a road test followed by another check with the diagnostic tool.

DIESEL INJECTION
Fault finding – Interpretation of faults13B
13B-80V3 MR-372-J84-13B250$360.mif
EDC16
PROGRAM No.: C1
Vdiag No.: 51
DF053
CONTINUED 2
1.DEF
NOTESNone
Ch eck the rail pressure regulator connectors.
Ch eck the in jection computer connections.
Ch eck the lo w p ressu re circu it b y runningtest 2Low pressure circuit check.
Ch eck the conformityof the fuel used by applyingtest 10 Diesel f uel conformity check.
Ch eck the in jector return flow, runtest 8 Poor injector operation.
Ch eck theoperation of the overpressure valve if fitted to the vehicle, run test11 Incorrectopera tion of the
ov erpressure valve.
Re pair if n ecessa ry.
Measure theresistanceof the rail press u r e regulator betweentracks 1 and 2.
If the resistance is not3±1Ωat20˚C,replacetheinjection pump.
Ch eckthe continuity and absence of interference resistanceof the followingconnections:
Injection computer brown 48-track
connectorB,track M4Track 2 of the rail pressure regulator (fuel flow actuator)
Injection supply relay mountingtrack 5 track 1 of the rail pressure regulator (fuel flow actuator)
Re pair if n ecessa ry.
Ch eck the rail pressuresensor using the interpretation ofDF0 07 Rail pressure sensor circuit.
Re pair if n ecessa ry.
If the fault isstill present,check t hat thecomputeroutput is working correctly.
●Either using anammeter:
With the regulator connected, connect the current clamp to the regulator'strack 1connection,respecting t he
direction of the current.
Cle ar a ny rail pressure sensor faults and use commandAC011 Rail pressureregulator.
Th eammeter should display ten cycles of two successive currents:~0.6Athen~2A.
AFTER REPAIRDeal with any faults.
Carry out a road test followed by another check with the diagnostic tool.

DIESEL INJECTION
Fault finding – Interpretation of faults13B
13B-81V3 MR-372-J84-13B250$360.mif
AFTER REPAIRDeal with any faults.
Carry out a road test followed by another check with the diagnostic tool.
EDC16
PROGRAM No.: C1
Vdiag No.: 51
*Opening cyclic ratioDF053
CONTINUED 3
●Or usingavoltmeter:
With the regulator connected, connect the negative terminal of the voltmeter totrack 2of the rail pressure regulator
and thepositive terminal totrack 1.Clear any fuel pressure solenoid valve faults, then run commandAC011 Rail
pressure re gulator:
Thevoltmeter should display two successive voltage readings:
~3.15voltsfor an opening cycle ratio of 25% then~9.45Vfor an opening cycle ratio of 75% (ten cycles).
●Or using an oscillos cope(at 5 V range/division a nd 1 ms/div tim e base):
With the regulator connected, connect the negative terminal of the oscill oscope to the battery earth and the positive
terminal totrack 2of the fuel pressure solenoid valve, clear any r ail pressure regulator faults, and r un command
AC0 11 R ail pressure regulator:
theoscillo sco pe sh ould disp lay a square pulse signal with an a mplitude o f 1 2.5 V at a frequency of 1 85 Hz (with a n
OCR* alternating successively from 25 to 75%).
if the measurement does not show any control or continuous voltage, contact the techline.

DIESEL INJECTION
Fault finding – Interpretation of faults13B
13B-82V3 MR-372-J84-13B250$360.mif
DF053
CONTINUED 4
2.DEF to
8.DEF
NOTESNone
Check the rail pressure regulator connectors.
Check the injection computer connections.
Check the low pressure circuit by running test 2 Low pressure circuit check.
Check the conformity of the fuel used by applying test 10 Diesel fuel conformity check.
Check the injector return flow, run test 8 Poor injector operation.
Check the operation of the overpressure valve if fitted to the vehicle, run test 11 Incorrect operation of the
overpressure valve.
Repair if necessary.
Measure the resistance of the pressure regulator between its tracks 1 and 2.
If the resistance is not 3 ± 1 Ω at 20˚C, replace the injection pump.
Check the continuity and for the absence of interference resistance on the following connections:
Injection computer brown 48-track
connector B, track M4Track 2 of the rail pressure regulator
Injection supply relay mounting track 5 track 1 of the rail pressure regulator
Repair if necessary.
AFTER REPAIRDeal with any faults.
Carry out a road test followed by another check with the diagnostic tool.
EDC16
PROGRAM No.: C1
Vdiag No.: 51

DIESEL INJECTION
Fault finding – Interpretation of faults13B
13B-83V3 MR-372-J84-13B250$360.mif
EDC16
PROGRAM No.: C1
Vdiag No.: 51
DF053
CONTINUED 5
In the event of rail overpressure:
Check the operation of the injectors: refer to test 8 Poor injector operation.
Check that the rail pressure sensor is operating correctly using command AC011 Rail pressure regulator. Display
parameter PR038 Rail pressure, and refer to the conformity check to check the operating values.
If these checks do not reveal any faults, and if the fault is still present, replace the injection pump.
in the event of rail underpressure:
Check that the rail pressure sensor is operating correctly using command AC011 Rail pressure regulator. Display
parameter PR038 Rail pressure, and refer to the conformity check to check the operating values.
Check the low pressure diesel circuit priming.
Check the conformity of the diesel filter connections.
Check the condition of the filter (clogging and water saturation).
Check that there are no air bubbles between the filter and the high pressure pump.
Check the low and high pressure diesel fuel circuit sealing (visual inspections, odour, etc.): pump housing,
pressure relief valve, pipes, rail and injector unions, injector wells, etc.
Check the operation of the injectors: refer to test 8 Poor injector operation.
Carry out the necessary operations.
If the fault is still present, replace the injection pump.
AFTER REPAIRDeal with any faults.
Carry out a road test followed by another check with the diagnostic tool.

DIESEL INJECTION
Fault finding – Interpretation of faults13B
13B-94V3 MR-372-J84-13B250$405.mif
EDC16
PROGRAM No.: C1
Vdiag No.: 51
DF057
PRESENT
OR
STOREDWATER IN DIESEL FUEL DETECTOR CIRCUIT
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is declared present after the engine is started or following a road test.
Check the conformity of the fuel used by applying test 10 Diesel fuel conformity check.
Check the sealing of the tank and low pressure circuit by applying test 2 Low pressure circuit check.
A) Make sure the water in diesel fuel detection sensor is properly connected.
–If not, clear the fault,
–Carry out a road test (speed > 12 mph (20 km/h) and engine speed > 1200 rpm) for more than 30 seconds.
–If the fault does not recur, end the fault finding procedure.
–If the fault does recur, go to step C.
B) If the water detection sensor is absent:
–Insulate the electrical connector not connected to the vehicle (risk of dampness, oxidation, and erratic
appearance of faults).
Check that the configuration reading LC065 Water detected in the diesel is NONE.
If LC065 is WITH, run command RZ005 Programming to reinitialise the vehicle configurations.
–Clear the faults.
–Carry out a road test (speed > 12 mph (20 km/h) and engine speed > 1200 rpm) for more than 30 seconds.
–If the fault does not recur, end the fault finding procedure.
C) If the sensor is properly connected:
–Bleed the diesel filter unit (see MR 364, Mechanics, 13A, Fuel supply).
–Clear the fault.
–Carry out a road test (speed > 12 mph (20 km/h) and engine speed > 1200 rpm) for more than 30 seconds.
–If the fault does not recur, end the fault finding procedure.
D) If the fault recurs:
–Check for continuity and the absence of interference resistance on the connection between:
Injection computer 32-track grey connector track A2 Track 3 of the water detection sensor
AFTER REPAIRDeal with any faults.
Carry out a road test followed by another check with the diagnostic tool.
EDC16_V51_DF057

DIESEL INJECTION
Fault finding – Conformity check13B
13B - 137V3 MR-372-J84-13B250$450.mif
EDC16
PROGRAM NO.: C1
Vdiag No.: 51
FUEL CIRCUIT
*Opening cyclic ratio signal
NOTESOnly check conformity after a complete check using the diagnostic tool. The values
shown in this conformity check are given as a guide.
Test conditions: ENGINE OFF, IGNITION ON.
Order FunctionParameter or Status
checked or ActionDisplay and Notes Fault finding
1Engine speedPR055:Engine speedIndicates the engine's
rotational speed in rpm.
With the ignition on,
0 rpm.In the event of a fault, refer
to the interpretation for
fault DF005 Engine
speed sensor circuit.
2Injector codesET104:Injector code
useYES
Indicates whether the
injector codes have been
programmedIn the event of a fault,
consult the interpretation
of DF276 Injector code
programming.
3PressurePR008:Rail pressure
setpointIndicates the theoretical
pressure value for
optimum engine operation
X = 250 ± 50 barIn the event of a fault, refer
to the interpretation of
faults DF053 Rail
pressure regulation
function and DF007 Rail
pressure sensor circuit. PR038:Rail pressure0 < X < 10 bar
Default value: 250 bar.
PR048:OCR* rail
pressure
regulation valveX = 15 %
PR213:Rail pressure
loop differenceX = PR008 - PR038The fuel pressure
variation is the difference
between the rail pressure
and the rail pressure
setpoint. In the event of a
fault, consult the
interpretation of faults
DF007 Rail pressure
sensor circuit and
DF053 Rail pressure
regulation function.

DIESEL INJECTION
Fault finding – Conformity check13B
13B - 138V3 MR-372-J84-13B250$450.mif
EDC16
PROGRAM NO.: C1
Vdiag No.: 51
FUEL CIRCUIT (continued)
NOTESOnly check conformity after a complete check using the diagnostic tool. The values
shown in this conformity check are given as a guide.
Test conditions: ENGINE OFF, IGNITION ON.
Order FunctionParameter or Status
checked or ActionDisplay and Notes Fault finding
4FlowPR157:Fuel flow setpoint0 < X < 60 mg/stNone
PR017:Fuel flowPR017 = PR157None
PR364:Cylinder no. 1
fuel flow
correction
0.0 mg/stIn the event of a fault, refer
to test 8: POOR
INJECTOR OPERATION. PR405:Cylinder no. 2
fuel flow
correction
PR406:Cylinder no. 3
fuel flow
correction
PR365:Cylinder no. 4
fuel flow
correction
5Rail currentPR007:Rail pressure
regulator current
setpointX = 400 ± 5 mA
Default value:
1600 mAIn the event of a fault,
consult the interpretation
of faults DF053 Rail
pressure regulation
function and DF007 Rail
pressure sensor circuit. PR006:Rail pressure
regulator currentX = PR007 ± 5 mA
Default value:
1600 mA
PR080:Rail pressure
sensor voltageX = 0.5 V
Safe value: 5 VIn the event of a fault, refer
to the interpretation of
fault DF013 Sensor feed
voltage no. 3. 6Sensor voltagePR080:Rail pressure
sensor voltage0.5 < X < 1 V
Safe value: 5 V