2009 RENAULT SCENIC ESP

AUTOMATIC TRANSMISSION
Fault finding - Interpretation of parameters
23A
23A - 138V3 MR-372-J84-23A000$765.mif
AJ0 BVA
Vdiag No.: 04, 05
PR008
COMPUTER SUPPLY VOLTAGE
PARAMETER
DEFINITIONThis parameter shows the computer feed voltage in volts.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system operation
programming.
No faults should be present or stored.
Conformity check with engine stopped and ignition on, engine running, engine coolant
temperature > 80 ˚C
Look for any damage to the wiring and check the condition and connection of the connectors for components 119
and 1337.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the continuity and insulation of the following connections:
●Connection code BP42,
between components 119 and 1337.
●Connection code AP4,
between components 119 and 1337.
Check for + 12 V after ignition feed on connection BP42 of component 119.
Check for + 12 V after ignition feed on connection AP4 of component 119.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check for earth on connection N of component 119.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact Techline.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
AJ0_V04_PR008/AJ0_V05_PR008

AUTOMATIC TRANSMISSION
Fault finding - Interpretation of parameters
23A
23A - 139V3 MR-372-J84-23A000$765.mif
AJ0 BVA
Vdiag No.: 04, 05
PR022
ACCELERATOR PEDAL POSITION
Note:
Parameter PR022 "Accelerator pedal position" applies to the following sub-functions:
"Gear changes".
"Torque activation".
"Driver parameters".
PARAMETER
DEFINITIONThis parameter indicates the accelerator pedal position as a %.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system operation
programming.
No faults should be present or stored.
Conformity check with engine stopped and ignition on
Full load: PR022 "Accelerator pedal position" ≈≈ ≈ ≈
114 % and PR067 "Calculated accelerator pedal position"
= 100 %.
In the event of a fault (see 13B EDC16 CP33 M9R 721, Interpretation of faults, DF196 "Pedal sensor gang 1
circuit" or DF198 "Pedal sensor gang 2 circuit").
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
AJ0_V04_PR022/AJ0_V05_PR022

AUTOMATIC TRANSMISSION
Fault finding - Interpretation of parameters
23A
23A - 140V3 MR-372-J84-23A000$765.mif
AJ0 BVA
Vdiag No.: 04, 05
PR067
CALCULATED ACCELERATOR PEDAL POSITION
Note:
Parameter PR067 "Accelerator pedal position" applies to the following sub-functions:
"Gear changes".
"Torque activation".
PARAMETER
DEFINITIONThis signal is supplied by the injection computer when the cruise control/speed limiter
is operating and when there is no longer a signal from the accelerator pedal. This
parameter indicates the accelerator pedal position as a %.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system operation
programming.
No faults should be present or stored.
Conformity check with engine stopped and ignition on, engine running, engine coolant
temperature > 80 ˚C
Full load: PR022 "Accelerator pedal position" ≈≈ ≈ ≈
114 % and PR067 "Calculated accelerator pedal position"
= 100 %.
In the event of a fault (see 13B EDC16 CP33 M9R 721, Interpretation of faults, DF196 "Pedal sensor gang 1
circuit" or DF198 "Pedal sensor gang 2 circuit").
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
AJ0_V04_PR067/AJ0_V05_PR067

AUTOMATIC TRANSMISSION
Fault finding - Interpretation of parameters
23A
23A - 141V3 MR-372-J84-23A000$765.mif
AJ0 BVA
Vdiag No.: 04, 05
PR105
VEHICLE SPEED
Note:
Parameter PR105 "Vehicle speed" applies to the following sub-functions:
"Gear changes".
"Driver parameters".
PARAMETER
DEFINITIONThis parameter indicates the vehicle speed in mph (km/h).
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system operation
programming.
No faults should be present or stored.
Conformity check with engine stopped and ignition on
0 mph (km/h)
In the event of a fault, consult the interpretation of fault DF171 Vehicle speed sensor circuit.
Conformity check with engine running, engine coolant temperature > 80 ˚C
In the event of a fault, consult the interpretation of fault DF171 Vehicle speed sensor circuit.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
AJ0_V04_PR105/AJ0_V05_PR105

AUTOMATIC TRANSMISSION
Fault finding - Interpretation of parameters
23A
23A - 142V3 MR-372-J84-23A000$765.mif
AJ0 BVA
Vdiag No.: 04, 05
PR106
EFFECTIVE ENGINE TORQUE
Note:
Parameter PR106 "Effective engine torque" applies to the following sub-functions:
"Gear changes".
"Torque activation".
PARAMETER
DEFINITIONThis parameter indicates the effective engine torque in Nm. This signal is supplied to
the gearbox computer by the injection computer.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system operation
programming.
No faults should be present or stored.
Conformity check with engine ignition on and engine running at idle speed.
PR006 "Engine
speed"PR007 "Turbine
speed"PR106 "Effective
engine torque"PR153 "Slow
torque"PR154 "Fast
torque"
0 rpm 0 rpm 140 Nm 360 Nm - 32 Nm
≈ 802 rpm≈ 704 rpm≈ 34 Nm≈ 360 Nm≈ - 30 Nm
In the event of a fault, carry out a multiplex network test (see 88B, Multiplexing).
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
AJ0_V04_PR106/AJ0_V05_PR106

AUTOMATIC TRANSMISSION
Fault finding - Interpretation of parameters
23A
23A - 143V3 MR-372-J84-23A000$765.mif
AJ0 BVA
Vdiag No.: 04, 05
PR153
SLOW TORQUE SETPOINT
Note:
Parameter PR153 "Slow torque setpoint" applies to the following sub-function:
"Slow torque activation".
PARAMETER
DEFINITIONThis parameter indicates the slow torque setpoint in Nm.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system operation
programming.
No faults should be present or stored.
Conformity check with engine ignition on and engine running at idle speed.
PR006 "Engine
speed"PR007 "Turbine
speed"PR106 "Effective
engine torque"PR153 "Slow
torque"PR154 "Fast
torque"
0 rpm 0 rpm 140 Nm 360 Nm - 32 Nm
≈ 802 rpm≈ 704 rpm≈ 34 Nm≈ 360 Nm≈ - 30 Nm
In the event of a fault, carry out a multiplex network test (see 88B, Multiplexing).
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
AJ0_V04_PR153/AJ0_V05_PR153

AUTOMATIC TRANSMISSION
Fault finding - Interpretation of parameters
23A
23A - 144V3 MR-372-J84-23A000$765.mif
AJ0 BVA
Vdiag No.: 04, 05
PR154
FAST TORQUE SETPOINT
Note:
Parameter PR154 "Fast torque setpoint" applies to the following sub-function:
"Torque activation".
PARAMETER
DEFINITIONThis parameter indicates the fast torque setpoint in Nm.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system operation
programming.
No faults should be present or stored.
Conformity check with engine ignition on and engine running at idle speed.
PR006 "Engine
speed"PR007 "Turbine
speed"PR106 "Effective
engine torque"PR153 "Slow
torque"PR154 "Fast
torque"
0 rpm 0 rpm 140 Nm 360 Nm - 32 Nm
≈ 802 rpm≈ 704 rpm≈ 34 Nm≈ 360 Nm≈ - 30 Nm
In the event of a fault, carry out a multiplex network test (see 88B, Multiplexing).
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
AJ0_V04_PR154/AJ0_V05_PR154

AUTOMATIC TRANSMISSION
Fault finding - Fault Finding Chart
23A
23A - 157V3 MR-372-J84-23A000$945.mif
AJ0 BVA
Vdiag No.: 04, 05
ALP1
CONTINUED
Check for + 12 V on connection BP42 of component 119.
Check for + after ignition feed on connection AP4 of component 119.
Check for earth on connection N of component 119.
Check the insulation and the continuity of the following connections:
●connection code 3MS,
●connection code 3MT,
between components 119 and 120.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Run a multiplex network test (see 88B, Multiplex).
If the computer still does not respond, contact the Techline.
AFTER REPAIRDeal with any faults detected by the diagnostic tool. Clear the computer memory.
Carry out a road test, then check with the diagnostic tool.