2009 PONTIAC VIBE heater

If the On Indicator is Lit for a
Child Restraint
If a child restraint has been installed
and the on indicator is lit:
1. Turn the vehicle off.
2. Remove the child restraint from
the vehicle.
3. Remove any additional items
from the seat such as blankets,
cushions, seat covers, seat
heaters, or seat massagers.
4. Reinstall the child restraint with
the ignition key in the ACC or
LOCK position while following the
directions provided by the child
restraint manufacturer and
refer toSecuring Child Restraints
(Right Front Seat) on page 1-50
orSecuring Child Restraints
(Rear Seats) on page 1-53.5. If, after reinstalling the child
restraint and restarting the
vehicle, the on indicator is still lit,
turn the vehicle off. Then slightly
recline the vehicle seatback
and adjust the seat cushion, if
adjustable, to make sure that the
vehicle seatback is not pushing
the child restraint into the seat
cushion.
6. Also make sure the child restraint
is not trapped under the vehicle
head restraint. If this happens,
adjust the head restraint.
SeeHead Restraints on
page 1-6.
If the on indicator is still lit, secure
the child in the child restraint in
a rear seat position in the vehicle,
and check with your dealer/retailer.
If the Off Indicator is Lit for an
Adult-Size Occupant
If a person of adult-size is sitting in
the right front passenger seat,
but the off indicator is lit, it could be
because that person is not sitting
properly in the seat.
Seats and Restraints 1-31
2009 - Pontiac Vibe Owner Manual

If this happens, use the following
steps to allow the system to detect
that person and enable the right
front passenger frontal airbag
and seat-mounted side impact
airbag (if equipped):
1. Turn the vehicle off.
2. Remove any additional material
from the seat, such as blankets,
cushions, seat covers, seat
heaters, or seat massagers.
3. Place the seatback in the fully
upright position.
4. Have the person sit upright in
the seat, centered on the seat
cushion, with legs comfortably
extended.
5. Restart the vehicle and have the
person remain in this position for
two to three minutes after the
on indicator is lit.Additional Factors Affecting
System Operation
Safety belts help keep the passenger
in position on the seat during vehicle
maneuvers and braking, which helps
the passenger sensing system
maintain the passenger airbag
status. See “Safety Belts” and “Child
Restraints” in the Index for additional
information about the importance of
proper restraint use.
A thick layer of additional material,
such as a blanket or cushion, or
aftermarket equipment such as
seat covers, seat heaters, seat
backpacks, and seat massagers
can affect how well the passenger
sensing system operates. We
recommend that you not use
seat covers or other aftermarket
equipment except when approved
by GM for your specic vehicle.
SeeAdding Equipment to Your
Airbag-Equipped Vehicle on
page 1-34for more information
about modications that can affect
how the system operates.The passenger sensing system may
suppress the airbag deployment
when liquid soaks into the seat.
If this happens, the off indicator
in the passenger airbag status
indicator and the airbag readiness
light will be lit. Have your
dealer/retailer check the system.
An object, person or child in the
rear seat contacting or pressing the
right front passenger seatback,
or objects stowed under the right
front passenger seat, may affect the
proper functioning of the passenger
sensing system.
When a safety belt extender is used
in the right front passenger seat,
make sure the passenger airbag
status indicator shows ON. If the
indicator shows OFF, disconnect the
extender’s latch from the buckle then
reconnect the safety belt.
1-32 Seats and Restraints
2009 - Pontiac Vibe Owner Manual

Adding Equipment to
Your Airbag-Equipped
Vehicle
Q:Is there anything I might add to
or change about the vehicle
that could keep the airbags
from working properly?
A:Yes. If you add things that
change the vehicle’s frame,
bumper system, height, front end
or side sheet metal, they may
keep the airbag system from
working properly. Changing or
moving any parts of the front
seats, safety belts, the airbag
sensing and diagnostic module,
steering wheel, instrument
panel, roof-rail airbag modules,
ceiling headliner or pillar
garnish trim, front sensors, or
airbag wiring can affect the
operation of the airbag system.In addition, the vehicle has a
passenger sensing system for the
right front passenger position,
which includes sensors that are
part of the passenger’s seat.
The passenger sensing system
may not operate properly if the
original seat trim is replaced with
non-GM covers, upholstery or
trim, or with GM covers,
upholstery or trim designed for a
different vehicle. Any object, such
as an aftermarket seat heater or a
comfort enhancing pad or device,
installed under or on top of the
seat fabric, could also interfere
with the operation of the
passenger sensing system.
This could either prevent proper
deployment of the passenger
airbag(s) or prevent the
passenger sensing system from
properly turning off the passenger
airbag(s). SeePassenger
Sensing System on page 1-28.If you have any questions, call
Customer Assistance. The phone
numbers and addresses for
Customer Assistance are in
Step Two of the Customer
Satisfaction Procedure in
this manual. SeeCustomer
Satisfaction Procedure on
page 12-1.Q:Because I have a disability,
I have to get my vehicle
modied. How can I nd out
whether this will affect my
airbag system?
A:If you have questions, call
Customer Assistance. The phone
numbers and addresses for
Customer Assistance are in
Step Two of the Customer
Satisfaction Procedure in this
manual. SeeCustomer
Satisfaction Procedure on
page 12-1.
In addition, your dealer/retailer and
the service manual have information
about the location of the airbag
sensors, sensing and diagnostic
module and airbag wiring.
1-34 Seats and Restraints
2009 - Pontiac Vibe Owner Manual

Driving and
Operating
Starting and Operating
Your Vehicle
New Vehicle Break-In.........8-2
Ignition Positions................8-2
Retained Accessory
Power (RAP).....................8-4
Starting the Engine.............8-4
Engine Coolant Heater.......8-5
Automatic Transmission
Operation (Four Speed). . . .8-6
Automatic Transmission
Operation (Five Speed).....8-8
Manual Transmission
Operation........................8-11
Parking Brake...................8-12
Shifting Into Park..............8-13
Shifting Out of Park..........8-14
Parking the Vehicle
(Manual Transmission). . . .8-15
Parking Over Things
That Burn........................8-16
Engine Exhaust.................8-16
Running the Vehicle
While Parked..................8-17
Driving Your Vehicle
Defensive Driving..............8-17
Drunk Driving....................8-18
Control of a Vehicle..........8-18
Braking.............................8-19
Antilock Brake
System (ABS).................8-20
Traction Control
System (TCS).................8-21
All-Wheel Drive (AWD)
System............................8-22
StabiliTrak®System..........8-22
Steering............................8-23
Off-Road Recovery............8-24
Passing.............................8-25
Loss of Control.................8-25
Driving at Night.................8-26
Driving in Rain and on
Wet Roads......................8-27
Before Leaving on a
Long Trip........................8-28
Highway Hypnosis.............8-28
Hill and Mountain Roads. . .8-28
Winter Driving...................8-29
If Your Vehicle is Stuck in
Sand, Mud, Ice, or Snow. . .8-31
Rocking Your Vehicle to
Get It Out.......................8-31
Loading the Vehicle..........8-32
Fuel
Fuel..................................8-36
Gasoline Octane...............8-36
Gasoline Specications.....8-36
California Fuel..................8-36
Additives...........................8-37
Fuels in Foreign
Countries........................8-37
Filling the Tank.................8-38
Filling a Portable Fuel
Container........................8-40
Driving and Operating 8-1
2009 - Pontiac Vibe Owner Manual

2. If the engine does not start, wait
about 15 seconds and try again
to start the engine by turning
the ignition to START. Wait about
15 seconds between each try.
When the engine has run
about 10 seconds to warm up,
the vehicle is ready to be driven.
Do not run the engine at high
speed when it is cold.
If the weather is below freezing
(32°F or 0°C), let the engine run
for a few minutes to warm up.
3. If the engine still will not start, or
starts but then stops, it could be
ooded with too much gasoline.
Try pushing the accelerator pedal
all the way to the oor and holding
it there as you hold the key in
START for about three seconds.
If the vehicle starts briey but then
stops again, do the same thing,
but this time keep the pedal down
for ve or six seconds. This clears
the extra gasoline from the
engine.Notice:The engine is designed
to work with the electronics in
the vehicle. If electrical parts or
accessories are added, you could
change the way the engine
operates. Before adding electrical
equipment, check with your
dealer/retailer. If you do not,
the engine might not perform
properly. Any resulting damage
would not be covered by the
vehicle warranty.
Engine Coolant Heater
The engine coolant heater, if
available, can help in cold weather
conditions at or below 0°F (−18°C)
for easier starting and better fuel
economy during engine warm-up.
Plug in the coolant heater at least
four hours before starting the vehicle.
To Use the Engine Coolant
Heater
1. Turn off the engine.
2. Open the hood and unwrap the
electrical cord. The electrical
cord is located on the driver side
of the engine compartment.
3. Plug it into a normal, grounded
110-volt AC outlet.
{CAUTION
Plugging the cord into an
ungrounded outlet could cause
an electrical shock. Also, the
wrong kind of extension cord could
overheat and cause a re. You
could be seriously injured. Plug the
cord into a properly grounded
three-prong 110-volt AC outlet.
If the cord will not reach, use a
heavy-duty three-prong extension
cord rated for at least 15 amps.
Driving and Operating 8-5
2009 - Pontiac Vibe Owner Manual

4. Before starting the engine, be
sure to unplug and store the
cord as it was before to keep
it away from moving engine
parts. If you do not, it could
be damaged.
The length of time the heater should
remain plugged in depends on
several factors. Ask a dealer/retailer
in the area where you will be parking
the vehicle for the best advice
on this.Automatic Transmission
Operation (Four Speed)
The shift lever is located on the
console between the seats.
P (Park):This position locks the
front wheels. It is the best position
to use when you start the engine
because the vehicle cannot
move easily.
{CAUTION
It is dangerous to get out of the
vehicle if the shift lever is not fully
in P (Park) with the parking brake
rmly set. The vehicle can roll.
Do not leave the vehicle when the
engine is running unless you have
to. If you have left the engine
running, the vehicle can move
suddenly. You or others could be
injured. To be sure the vehicle will
not move, even when you are on
fairly level ground, always set the
parking brake and move the shift
lever to P (Park). SeeShifting Into
Park on page 8-13. If you are
pulling a trailer, seeTowing a
Trailer on page 9-77.
Make sure the shift lever is
fully in P (Park) before starting
the engine. The vehicle has
an automatic transmission
shift lock control system.
8-6 Driving and Operating
2009 - Pontiac Vibe Owner Manual

Cooling System
When it is safe lift the hood:
A. Electric Engine Cooling Fans
B. Pressure Cap
C. Engine Coolant Recovery Tank{CAUTION
An electric engine cooling fan
under the hood can start up even
when the engine is not running
and can cause injury. Keep
hands, clothing, and tools away
from any underhood electric fan.
{CAUTION
Heater and radiator hoses, and
other engine parts, can be very
hot. Do not touch them. If you do,
you can be burned.
Do not run the engine if there
is a leak. If you run the engine, it
could lose all coolant. That could
cause an engine re, and you
could be burned. Get any leak
xed before you drive the vehicle.
Engine Coolant
The coolant in the vehicle should
last for ve years or 150,000 miles
(240 000 km), whichever occurs
rst. When coolant is added
or changed, use DEX-COOL
®
coolant.
The following explains the cooling
system and how to add coolant when
it is low. If there is a problem with
engine overheating, seeEngine
Overheating on page 9-22Engine
Overheating.
What to Use
Use a 50/50 mixture of clean,
drinkable water and DEX-COOL®
coolant, which will not damage
aluminum parts. If this coolant
mixture is used, nothing else
needs to be added.
9-18 Vehicle Service and Care
2009 - Pontiac Vibe Owner Manual

{CAUTION
Adding only plain water to the
cooling system can be dangerous.
Plain water, or some other liquid
such as alcohol, can boil before
the proper coolant mixture will.
The vehicle’s coolant warning
system is set for the proper
coolant mixture. With plain water
or the wrong mixture, the engine
could get too hot but would not
get the overheat warning. The
engine could catch re and you
or others could be burned. Use a
50/50 mixture of clean, drinkable
water and DEX-COOL
®coolant.
Notice:If an improper coolant
mixture is used, the engine could
overheat and be badly damaged.
The repair cost would not be
covered by the vehicle warranty.
Too much water in the mixture
can freeze and crack the engine,
radiator, heater core, and other
parts.Notice:If you use extra
inhibitors and/or additives in
your vehicle’s cooling system,
you could damage your vehicle.
Use only the proper mixture of
the engine coolant listed in this
manual for the cooling system.
SeePart D: Recommended Fluids
and Lubricants on page 11-18for
more information.
Gives freezing protection down to
−34°F (−38°C).
Gives boiling protection up to
265°F (129°C).
Protects against rust and
corrosion.
Helps keep the proper engine
temperature.
Lets the warning lights and gages
work as they should.
Notice:Using coolant other than
DEX-COOL can cause premature
engine, heater core or radiator
corrosion. In addition, the enginecoolant may require changing
sooner, at 30,000 miles
(50 000 km) or 24 months,
whichever occurs rst. Any
repairs would not be covered by
the vehicle warranty. Always
use DEX-COOL (silicate-free)
coolant in your vehicle.
Checking Coolant
The vehicle must be on a level
surface. When the engine is cold,
the coolant level should be at LOW,
or a little higher. When the engine
is warm, the level should be up to
FULL, or a little higher. If it is not,
there could be a leak at the pressure
cap or in the radiator hoses, heater
hoses, radiator, water pump, or
somewhere else in the cooling
system.
SeeEngine Compartment Overview
on page 9-6Engine Compartment
Overview for the location of the
coolant recovery tank.
Vehicle Service and Care 9-19
2009 - Pontiac Vibe Owner Manual