2009 PONTIAC VIBE engine

1. Release the three clips that hold
the cover.2. Lift the cover.
3. Inspect or replace the engine air
cleaner/lter.
4. Reinstall the cover.
{CAUTION
Operating the engine with the air
cleaner/lter off can cause you
or others to be burned. The air
cleaner not only cleans the air;
it helps to stop ames if the engine
backres. If it is not there and the
engine backres, you could be
burned. Do not drive with it off, and
be careful working on the engine
with the air cleaner/lter off.
Notice:If the air cleaner/lter
is off, a backre can cause a
damaging engine re. And, dirt
can easily get into the engine,
which will damage it. Always have
the air cleaner/lter in place when
you are driving. 2.4L Engine
Vehicle Service and Care 9-13
2009 - Pontiac Vibe Owner Manual

Automatic Transmission
Fluid
When to Check and Change
Automatic Transmission Fluid
Check the uid in the transmission
and differential at the intervals listed
inPart A: Scheduled Maintenance
Services on page 11-3, and be
sure to use the transmission uid
listed inPart D: Recommended
Fluids and Lubricants on
page 11-18.
How to Check Automatic
Transmission Fluid
This operation can be difficult, you
may choose to have this done at the
dealer/retailer service department.
If you do it yourself, be sure to follow
all the instructions here, or you
could get a false reading on
the dipstick.Notice:Use of the incorrect
automatic transmission uid may
damage your vehicle, and the
damages may not be covered by
your warranty. Always use the
automatic transmission uid
listed inPart D: Recommended
Fluids and Lubricants on
page 11-18.
Wait at least 30 minutes before
checking the transmission uid level
if you have been driving:
When outside temperatures are
above 90°F (32°C).
At high speed for quite a while.
In heavy traffic — especially
in hot weather.
While pulling a trailer.
To get the right reading, the uid
should be at normal operating
temperature, which is 158°F to
176°F (70°C to 80°C).Get the vehicle warmed up by
driving about 15 miles (24 km)
when outside temperatures are
above 50°F (10°C). If it is colder
than 50°F (10°C), you may have
to drive longer.
Checking the Fluid Level
Prepare your vehicle as follows:
1. Park your vehicle on a level
place. Keep the engine running.
2. With the parking brake applied,
place the shift lever in P (Park).
3. With your foot on the brake
pedal, move the shift lever
through each gear range,
pausing for about three seconds
in each range. Then, position
the shift lever in P (Park).
4. Let the engine run at idle for
three to ve minutes.
9-14 Vehicle Service and Care
2009 - Pontiac Vibe Owner Manual

Then, without shutting off the
engine, follow these steps:
The automatic transmission
dipstick has an orange handle
and is located near the front of the
engine compartment. SeeEngine
Compartment Overview on page 9-6
for more information on location.
1. Release the tab and pull out the
dipstick and wipe it with a clean
rag or paper towel.
2. Push it back in all the way, wait
three seconds and then pull it
back out again.
3. Check both sides of the dipstick,
and read the lower level. The
uid level must be between the
two dimples in the hot range.4. If the uid level is in the
acceptable range, push
the dipstick back in all the way;
then press the tab down to
lock the dipstick in place.
How to Add Automatic
Transmission Fluid
Refer to the Maintenance
Schedule to determine what
kind of transmission uid to use.
Part D: Recommended Fluids
and Lubricants on page 11-18.
If the uid level is low, add
only enough of the proper uid
to bring the level into the area
between dimples on the dipstick.
1. Pull out the dipstick.
2. Using a long-neck funnel, add
enough uid at the dipstick
hole to bring it to the proper level.
It does not take much uid,
generally less than one pint
(0.5 L). Do not overll.Notice:Too much or too
little uid can damage your
transmission. Too much can mean
that some of the uid could come
out and fall on hot engine parts or
exhaust system parts, starting a
re. Too little uid could cause the
transmission to overheat. Be sure
to get an accurate reading if you
check your transmission uid.
3. After adding uid, recheck the
uid level as described under
“How to Check Automatic
Transmission Fluid,” earlier
in this section.
4. When the correct uid level is
obtained, push the dipstick
back in all the way; then press
the tab down to lock the dipstick
in place.
1.8L shown
Vehicle Service and Care 9-15
2009 - Pontiac Vibe Owner Manual

Manual Transmission
Fluid
When to Check
A good time to have your manual
transmission uid level checked
is when the engine oil is changed.
However, the uid in your manual
transmission does not require
changing.
How to Check
This operation can be difficult, you
may choose to have this done
at your dealer/retailer service
department.
If you do it yourself, be sure to
follow all the instructions here,
or you could get a false reading.
Notice:Too much or too
little uid can damage your
transmission. Too much can
mean that some of the uid couldcome out and fall on hot engine
parts or exhaust system parts,
starting a re. Too little uid
could cause the transmission
to overheat. Be sure to get
an accurate reading if you
check your transmission uid.
Check the uid level only when your
engine is off, the vehicle is parked on
a level place and the transmission is
cool enough for you to rest your
ngers on the transmission case.
Then, follow these steps:
1. Remove the ller plug.
2. Check that the lubricant level is
up to the bottom of the ller
plug hole.
3. If the uid level is good, install
the plug and be sure it is fully
seated. If the uid level is low,
add more uid as described in
the next steps.
How to Add Fluid
Here is how to add uid. Refer
to the Maintenance Schedule
to determine what kind of uid to
use.Part D: Recommended
Fluids and Lubricants on
page 11-18.
1. Remove the ller plug.
2. Add uid at the ller plug hole.
Add only enough uid to bring
the uid level up to the bottom
of the ller plug hole.
3. Install the ller plug. Be sure the
plug is fully seated.
9-16 Vehicle Service and Care
2009 - Pontiac Vibe Owner Manual

Hydraulic Clutch
The hydraulic clutch linkage in
your vehicle is self-adjusting.
The master cylinder reservoir is
lled with DOT-3 brake uid.
It is not necessary to regularly check
the uid unless you suspect there
is a leak in the system. Adding uid
will not correct a leak.
The hydraulic clutch and brake
master cylinder use the same
reservoir.
A uid loss in this system could
indicate a problem. Have the system
inspected and repaired.
When to Check and What
to Use
The reservoir is located at the back
of the engine compartment, on the
driver side of the vehicle.Engine
Compartment Overview on page 9-6.Refer to the Maintenance Schedule
to determine how often you should
check the uid level in your master
cylinder reservoir and for the proper
uid.Part B: Owner Checks and
Services on page 11-12andPart D:
Recommended Fluids and
Lubricants on page 11-18.
How to Check and Add Fluid
Check that the uid level is at
or above the MIN mark. If the level
is below the MIN mark, see the
instructions on the reservoir cap.
Vehicle Service and Care 9-17
2009 - Pontiac Vibe Owner Manual

Cooling System
When it is safe lift the hood:
A. Electric Engine Cooling Fans
B. Pressure Cap
C. Engine Coolant Recovery Tank{CAUTION
An electric engine cooling fan
under the hood can start up even
when the engine is not running
and can cause injury. Keep
hands, clothing, and tools away
from any underhood electric fan.
{CAUTION
Heater and radiator hoses, and
other engine parts, can be very
hot. Do not touch them. If you do,
you can be burned.
Do not run the engine if there
is a leak. If you run the engine, it
could lose all coolant. That could
cause an engine re, and you
could be burned. Get any leak
xed before you drive the vehicle.
Engine Coolant
The coolant in the vehicle should
last for ve years or 150,000 miles
(240 000 km), whichever occurs
rst. When coolant is added
or changed, use DEX-COOL
®
coolant.
The following explains the cooling
system and how to add coolant when
it is low. If there is a problem with
engine overheating, seeEngine
Overheating on page 9-22Engine
Overheating.
What to Use
Use a 50/50 mixture of clean,
drinkable water and DEX-COOL®
coolant, which will not damage
aluminum parts. If this coolant
mixture is used, nothing else
needs to be added.
9-18 Vehicle Service and Care
2009 - Pontiac Vibe Owner Manual

{CAUTION
Adding only plain water to the
cooling system can be dangerous.
Plain water, or some other liquid
such as alcohol, can boil before
the proper coolant mixture will.
The vehicle’s coolant warning
system is set for the proper
coolant mixture. With plain water
or the wrong mixture, the engine
could get too hot but would not
get the overheat warning. The
engine could catch re and you
or others could be burned. Use a
50/50 mixture of clean, drinkable
water and DEX-COOL
®coolant.
Notice:If an improper coolant
mixture is used, the engine could
overheat and be badly damaged.
The repair cost would not be
covered by the vehicle warranty.
Too much water in the mixture
can freeze and crack the engine,
radiator, heater core, and other
parts.Notice:If you use extra
inhibitors and/or additives in
your vehicle’s cooling system,
you could damage your vehicle.
Use only the proper mixture of
the engine coolant listed in this
manual for the cooling system.
SeePart D: Recommended Fluids
and Lubricants on page 11-18for
more information.
Gives freezing protection down to
−34°F (−38°C).
Gives boiling protection up to
265°F (129°C).
Protects against rust and
corrosion.
Helps keep the proper engine
temperature.
Lets the warning lights and gages
work as they should.
Notice:Using coolant other than
DEX-COOL can cause premature
engine, heater core or radiator
corrosion. In addition, the enginecoolant may require changing
sooner, at 30,000 miles
(50 000 km) or 24 months,
whichever occurs rst. Any
repairs would not be covered by
the vehicle warranty. Always
use DEX-COOL (silicate-free)
coolant in your vehicle.
Checking Coolant
The vehicle must be on a level
surface. When the engine is cold,
the coolant level should be at LOW,
or a little higher. When the engine
is warm, the level should be up to
FULL, or a little higher. If it is not,
there could be a leak at the pressure
cap or in the radiator hoses, heater
hoses, radiator, water pump, or
somewhere else in the cooling
system.
SeeEngine Compartment Overview
on page 9-6Engine Compartment
Overview for the location of the
coolant recovery tank.
Vehicle Service and Care 9-19
2009 - Pontiac Vibe Owner Manual

How to Add Coolant to the
Coolant Recovery Tank
If you need more coolant, add the
proper DEX-COOL®coolant mixture
at the coolant recovery tank, but
be careful not to spill it.
Occasionally check the coolant level
in the radiator. For information on
how to add coolant to the radiator,
seeCooling System on page 9-18
Cooling System.
{CAUTION
You can be burned if you spill
coolant on hot engine parts.
Coolant contains ethylene glycol,
and it will burn if the engine parts
are hot enough. Do not spill
coolant on a hot engine.
{CAUTION
Adding only plain water to your
cooling system can be dangerous.
Plain water, or some other liquid
such as alcohol, can boil before
the proper coolant mixture will.
Your vehicle’s coolant warning
system is set for the proper
coolant mixture. With plain water
or the wrong mixture, your engine
could get too hot but you would
not get the overheat warning.
Your engine could catch re and
(Continued)
CAUTION (Continued)
you or others could be burned.
Use a 50/50 mixture of clean,
drinkable water and a proper
coolant.
Notice:In cold weather, water
can freeze and crack the engine,
radiator, heater core and other
parts. Use the recommended
coolant and the proper coolant
mixture.
How to Add Coolant to the
Radiator
When the coolant in the coolant
recovery tank is at the FULL mark,
start the vehicle.
If the overheat warning continues,
there is one more thing that can
be done. Add the proper coolant
mixture directly to the radiator but
be sure the cooling system is
cool before you do it.
9-20 Vehicle Service and Care
2009 - Pontiac Vibe Owner Manual