2009 Peugeot 607 Dag sensor
[x] Cancel search: sensorPage 5 of 182
9. Disarming of the passenger air bag * .
10. Passenger air bag.
11. Glove box/Video sockets.
12. Passenger footwell air outlet.
13. Passenger heated seat control.
14. Passenger seat electric controls.
15. Front ashtray/lighter (100 W max.).
16. Handbrake.
17. Gear lever.
18. Storage compartment.
19. Audio and telematics system.
20. Automatic air conditioning controls.
21. Central locking from the inside.
22. Multifunction display.
23. Hazard warning lights.
1. Steering lock and ignition.
2. Audio equipment steering wheel
control.
3. Wipers/wash-wipe and trip
computer controls.
4. Adjustable and closing central
vents.
5. Sunshine sensor.
6.
Windscreen de-icing and demisting vent.
7. Passenger side window de-icing
and demisting vent.
8. Adjustable and closing side vent.
* According to country.
Page 13 of 182
Front passenger air bag
1. Insertion of the key.
2. Selection of the "OFF" position.
3. Removal of the key keeping the
switch in this position. With the vehicle stationary, when the igni-
tion is switched on, the warning light comes
on if the driver and/or the front passenger
has not fastened his seat belt.
From approximately 12 mph (20 km/h)
and for two minutes, the warning light
fl a s h e s a c c o m p a n i e d b y a n a u d i b l e s i g n a l
which increases in volume. Once these
two minutes have elapsed, the warning
light remains on until the driver or front
passenger fastens his seat belt.
When the vehicle is moving, the warning
light comes on if the driver or one of the
front or rear passengers unfastens his
seat belt.
Seat belt not fastened/unfastened detection
82 80
Tyre under-inflation detection
Sensors check the pressure of the tyres
while driving and trigger a warning if
a malfunction occurs (speed above
15 mph (25 km/h)).
If one of the warning lights below ap-
pears, refer to the corresponding
paragraph.
79
Pressure OK
U n d e r - i n fl a t e d w h e e l
Punctured wheel
Page 39 of 182
3
39
VENTILATION
1. Windscreen de-icing or demisting
vents
2. Front window de-icing or
demisting vents
3. Side vents
4. Centre vents
5. Air outlets to the front passengers'
feet
6. Air outlets to the rear passengers'
feet
Recommendations for use and notes
If the interior temperature re-
mains very high following a prolonged
period parked in the sun, do not hesitate
to ventilate the passenger compartment
for a few minutes.
To obtain uniform air distribution, take
care not to obstruct the exterior air in-
take grille located at the bottom of the
windscreen, the vents, the air outlets
under the front seats and the air ex-
tractor in the boot.
In cold weather, in order to obtain uni-
form comfort, more rapid demisting
o r i f t h e fl o w o f a i r o n y o u r f a c e f e e l s
uncomfortable, it is advisable to close
vents 3 and 4.
When washing the vehicle using high
pressure equipment, do not direct
the jet towards the exterior air intake
grille.
To obtain optimum demisting, we
recommend that the windows are kept
clean on the inside of the vehicle.
In certain cases of particularly arduous
use (towing the maximum load on a
steep gradient when the temperature
is high), cutting off the air conditioning
permits the recovery of engine power
and, therefore, an increase in the tow-
ing capacity. For the air conditioning to be fully
effective, the windows must be closed.
Ensure that the passenger compart-
m e n t fi l t e r i s i n g o o d c o n d i t i o n . H a v e
t h e fi l t e r e l e m e n t s r e p l a c e d r e g u l a r l y .
If you drive in a dusty environment, re-
place them twice as often.
The air conditioning system does not
contain chlorine and does not present
any danger to the ozone layer.
Operate the air conditioning for 5 to
10 minutes, once or twice a month to
keep it in perfect working order.
The water resulting from the conden-
sation of the air conditioning system
is discharged via an opening provided
for this purpose. Therefore, a puddle
of water may form underneath the ve-
hicle when stationary.
If the system does not produce cold air,
do not use it and contact a PEUGEOT
dealer.
Flashing of the points separating the
setting value digits indicates a mal-
function of the air conditioning. Consult
a PEUGEOT dealer.
Use of the automatic regulation
of the air conditioning is recom-
mended. It permits optimised
automatic control of all of the
f o l l o w i n g f u n c t i o n s : a i r fl o w , p a s s e n g e r
compartment temperature and air distri-
bution, using various sensors (exterior
temperature and sunshine), so there is
no need to change your reference set-
tings other than the value displayed.
Page 64 of 182
4
59
ALARM Setting the alarm
S w i t c h o f f t h e i g n i t i o n a n d g e t o u t
o f t h e v e h i c l e .
S e t t h e a l a r m b y l o c k i n g o r d e a d -
locking using the remote control
(button A i n d i c a t o r l i g h t fl a s h e s
o n c e p e r s e c o n d ) .
When the alarm is triggered, the siren
sounds and the direction indicators
fl a s h f o r t h i r t y s e c o n d s .
T h e a l a r m r e m a i n s s e t f o l l o w i n g e a c h
t r i g g e r i n g i n c i d e n t .
U n l o c k t h e v e h i c l e w i t h t h e r e m o t e
control key (button B indicator light
g o e s o u t ) .
Note: if the alarm has been triggered
w h i l e y o u w e r e a w a y f r o m y o u r c a r , t h e
r a p i d fl a s h i n g o f t h e i n d i c a t o r l i g h t w i l l
s t o p w h e n y o u s w i t c h o n t h e i g n i t i o n .
Automatic activation *
The alarm is activated automatically
t w o m i n u t e s a f t e r t h e l a s t c l o s i n g o f a
d o o r o r t h e b o o t .
In order to avoid accidental triggering
o f t h e a l a r m w h e n a d o o r o r t h e b o o t
is opened, it is essential to press the
r e m o t e c o n t r o l o p e n i n g b u t t o n fi r s t .
* A c c o r d i n g t o c o u n t r y .
T h i s p r o v i d e s t w o t y p e s o f p r o t e c t i o n :
-
exterior protection , it sounds if
a door, the boot or the bonnet is
o p e n e d .
- interior protection , it sounds if
the sensors detect a variation in
t h e a i r m o v e m e n t i n s i d e t h e v e -
h i c l e ( b r e a k i n g o f a w i n d o w o r a
m o v e m e n t i n s i d e t h e v e h i c l e ) .
Warning: if the alarm has
been triggered ten times in
succession, on the eleventh
t i m e i t b e c o m e s i n a c t i v e .
Note: if button A fl a s h e s r a p i d l y , t h e
a l a r m h a s b e e n t r i g g e r e d w h i l e y o u
w e r e a w a y f r o m y o u r v e h i c l e .
I f y o u w i s h t o l o c k y o u r v e h i c l e w i t h o u t
s e t t i n g t h e a l a r m , u s e t h e d o o r l o c k .
Page 78 of 182
5
69
The timed duration must
also be set, via the multi-
function display "Person-
alisation-Configuration"
menu. Automatic switching on of the lights
Side lights and dipped beam head-
lamps switch on automatically if the
light is poor, or during operation of the
windscreen wipers. They switch off
as soon as the light becomes bright
enough or the windscreen wipers
stop.
In foggy weather or in snow, the bright-
n e s s s e n s o r c a n d e t e c t s u f fi c i e n t l i g h t .
Therefore, the lights will not come on
automatically. If necessary, you must
switch on the dipped headlamps man-
ually.
This function is active when the vehicle is
supplied to the customer.
To switch the function on
or off, use the multifunction
display "Personalisation-
C o n fi g u r a t i o n " menu.
Activation Deactivation.
When this function is activat-
ed, the indicator light on the
instrument panel comes on. When the function is deacti-
vated, the indicator light on the
instrument panel comes on.
Cancellation:
fl a s h t h e h e a d l a m p s ,
get out of the vehicle and lock it.
Manual "follow-me-home" lighting
In the absence of the automatic switching
on of the lights, the manual "follow-me-
home" lighting can be activated.
When you leave your vehicle, the side
lights and dipped headlamps remain
on for approximately 1 minute.
Activation:
switch off the engine,
fl a s h t h e h e a d l a m p s ,
get out of the vehicle and lock it.
Deactivation:
fl a s h t h e h e a d l a m p s a g a i n ,
get out of the vehicle and lock it.
If the brightness sensor does not func-
tion correctly , the system activates the
function and the lights come on.
Contact a PEUGEOT dealer to have
the system checked.
Daytime running lamps *
On vehicles which are equipped with day-
time running lamps, the dipped headlamps
come on when the vehicle is started.
This indicator lamp comes on on
the instrument panel screen.
The instruments and controls
(instrument panel, multifunc-
tion screen, air conditioning
control panel...) are only lit
on switching to the automatic lighting
mode or when the lights are switched
on manually.
* According to country.
The brightness of the display
and of the instrument panel
may change when the lights
are switched on automatically.
If your lights have been
switched on manually, turn the
ring back to position
0 , lights
off.
Page 79 of 182
5
69
The timed duration must
also be set, via the multi-
function display "Person-
alisation-Configuration"
menu. Automatic switching on of the lights
Side lights and dipped beam head-
lamps switch on automatically if the
light is poor, or during operation of the
windscreen wipers. They switch off
as soon as the light becomes bright
enough or the windscreen wipers
stop.
In foggy weather or in snow, the bright-
n e s s s e n s o r c a n d e t e c t s u f fi c i e n t l i g h t .
Therefore, the lights will not come on
automatically. If necessary, you must
switch on the dipped headlamps man-
ually.
This function is active when the vehicle is
supplied to the customer.
To switch the function on
or off, use the multifunction
display "Personalisation-
C o n fi g u r a t i o n " menu.
Activation Deactivation.
When this function is activat-
ed, the indicator light on the
instrument panel comes on. When the function is deacti-
vated, the indicator light on the
instrument panel comes on.
Cancellation:
fl a s h t h e h e a d l a m p s ,
get out of the vehicle and lock it.
Manual "follow-me-home" lighting
In the absence of the automatic switching
on of the lights, the manual "follow-me-
home" lighting can be activated.
When you leave your vehicle, the side
lights and dipped headlamps remain
on for approximately 1 minute.
Activation:
switch off the engine,
fl a s h t h e h e a d l a m p s ,
get out of the vehicle and lock it.
Deactivation:
fl a s h t h e h e a d l a m p s a g a i n ,
get out of the vehicle and lock it.
If the brightness sensor does not func-
tion correctly , the system activates the
function and the lights come on.
Contact a PEUGEOT dealer to have
the system checked.
Daytime running lamps *
On vehicles which are equipped with day-
time running lamps, the dipped headlamps
come on when the vehicle is started.
This indicator lamp comes on on
the instrument panel screen.
The instruments and controls
(instrument panel, multifunc-
tion screen, air conditioning
control panel...) are only lit
on switching to the automatic lighting
mode or when the lights are switched
on manually.
* According to country.
The brightness of the display
and of the instrument panel
may change when the lights
are switched on automatically.
If your lights have been
switched on manually, turn the
ring back to position
0 , lights
off.
Page 82 of 182
5
71
Automatic windscreen wiper
The automatic wiping is controlled by a
r a i n s e n s o r , fi t t e d o n t h e w i n d s c r e e n .
In AUTO mode, the wipers operate
automatically and adjust their speed
to the intensity of the rainfall .
Activation
Deactivation This warning light comes on
on the instrument panel, ac-
companied by a message
on the multifunction display,
when the driver presses the
wipers stalk down in
AUTO
mode.
This warning light comes on on
the instrument panel when the
driver moves the wipers stalk to
position I , 1 or 2 .
In the event of a malfunction , the
driver is informed of this by a message
on the multifunction display.
In AUTO mode, the wipers will then
operate in intermittent mode.
Contact a PEUGEOT dealer to have
the system checked.
Do not cover the rain sensor,
located on the windscreen be-
hind the interior mirror.
When using a car wash, switch
off the ignition.
In winter, it is advisable to wait until the
windscreen is completely clear of ice
before activating the automatic wipers.
When parking in snowy weather, position
the blades at the top of the windscreen
(maintenance position) to prevent the ac-
cumulation of snow.
Page 83 of 182
5
71
Automatic windscreen wiper
The automatic wiping is controlled by a
r a i n s e n s o r , fi t t e d o n t h e w i n d s c r e e n .
In AUTO mode, the wipers operate
automatically and adjust their speed
to the intensity of the rainfall .
Activation
Deactivation This warning light comes on
on the instrument panel, ac-
companied by a message
on the multifunction display,
when the driver presses the
wipers stalk down in
AUTO
mode.
This warning light comes on on
the instrument panel when the
driver moves the wipers stalk to
position I , 1 or 2 .
In the event of a malfunction , the
driver is informed of this by a message
on the multifunction display.
In AUTO mode, the wipers will then
operate in intermittent mode.
Contact a PEUGEOT dealer to have
the system checked.
Do not cover the rain sensor,
located on the windscreen be-
hind the interior mirror.
When using a car wash, switch
off the ignition.
In winter, it is advisable to wait until the
windscreen is completely clear of ice
before activating the automatic wipers.
When parking in snowy weather, position
the blades at the top of the windscreen
(maintenance position) to prevent the ac-
cumulation of snow.