2009 Peugeot 607 Dag headlamp
[x] Cancel search: headlampPage 113 of 182
9
97
2.7 LITRE V6 24V HDI DIESEL
ENGINE
1. Windscreen/headlamp wash
reservoir.
2. Power steering reservoir.
3. Coolant reservoir.
4. Dipstick.
5. E n g i n e o i l fi l l e r c a p .
6. A i r fi l t e r .
7. Fuse box.
8. B r a k e fl u i d r e s e r v o i r .
Page 114 of 182
9
98
CHECKING THE LEVELS
There are two marks on
the dipstick:
A = maximum
N e v e r fi l l p a s t t h i s m a r k .
B = minimum
To maintain the reliability
of engines and emission
control systems, the use
of additives in engine oil is
prohibited.
Dipstick
Oil change
According to the information given in
the servicing booklet.
The level must always be between the
DANGER and MAXIMUM marks in the
reservoir.
If the level drops substantially, contact
a PEUGEOT dealer immediately.
Windscreen and headlamp wash level
For best quality cleaning and for your
safety, we advise that you use prod-
ucts recommended by PEUGEOT
(reservoir capacity 4 litres or 6.5 litres
with headlamp wash).
Viscosity selection
In all cases, the oil selected must meet
the manufacturer's requirements. Fluid change:
- must be carried out according
to the manufacturer's servicing
schedule.
- u s e fl u i d s r e c o m m e n d e d b y t h e m a n u f a c t u r e r , w h i c h f u l fi l D O T 4
standards.
Used oil
Prevent used oil from coming
into prolonged contact with
the skin.
B r a k e a n d c l u t c h fl u i d i s h a r m f u l t o
health and very corrosive.
Do not dispose of used oil, brake and
c l u t c h fl u i d o r c o o l a n t i n t o d r a i n s o r
onto the ground.
Power steering reservoir
Open the reservoir, with the engine
cold at ambient temperature. The
level should always be above the
MINI mark and close to the MAXI
mark.
Oil level
Check the level regularly and top
up between changes.
Carry out this check with the vehicle
level, engine cold, using the oil level
gauge on the instrument panel or the
dipstick. C h a r a c t e r i s t i c s o f t h e fl u i d
For best quality cleaning and to pre-
v e n t f r e e z i n g , t h i s fl u i d m u s t n o t b e
topped up or replaced with water.
Page 119 of 182
1010
103
CHANGING A BULB
2 - Main beam headlamps: H1-55 W.
Turn the protective cover of the
faulty bulb a quarter of a turn and
remove it.
Disconnect the connector.
Press the end of the securing clip
to free it. Change the bulb.
W h e n fi t t i n g t h e n e w b u l b , e n s u r e
that the direction notches are po-
sitioned correctly and the securing
c l i p i s fi x e d p r o p e r l y .
Reconnect the connector.
R e fi t t h e p r o t e c t i v e c o v e r . 3 - S i d e l i g h t s : W 5 W .
Pull the socket rearwards.
Remove the bulb and change it.
Front foglamps: H1-55 W.
Handle the bulbs with a dry
cloth.
T h e h e a d l a m p s a r e fi t t e d w i t h
polycarbonate glass with a
protective coating. Do not clean them
with a dry or abrasive cloth, nor with a
detergent or solvent product.
Use a soft, damp cloth with soapy water.
In the engine compartment, remove
the style cover secured by one or two
b u t t e r fl y s c r e w s , a p l a s t i c r e t a i n e r c l i p
and two quarter turn screws.
On the left-hand side, remove the par-
tition by lifting it to gain access to the
lights.
W h e n y o u h a v e fi n i s h e d , d o n o t f o r g e t
to put everything back correctly.
W A R N I N G : R I S K O F E L E C -
TROCUTION
Xenon bulbs must be replaced
by a PEUGEOT dealer.
Front lights 1 - D i p p e d b e a m h e a d l a m p s : X e n o n b u l b . 4 - D i r e c t i o n i n d i c a t o r s :
PY 21 W (amber).
Turn the bulb holder a quarter turn
and remove it.
Remove the bulb and change it.
R e fi t t h e s t y l e c o v e r .
H i g h p r e s s u r e w a s h i n g
When using this type of washing on
stubborn dirt, do not persist on the
headlamps, the lights and their sur-
rounds to avoid damaging their var-
nish and their seal.
In certain climatic conditions
(low temperature, humidity),
condensation on the inside
surface of the glass of the
headlamps and rear lights is normal;
it disappears a few minutes after the
lights are switched on.
Page 126 of 182
1010
108
E n g i n e c o m p a r t m e n t f u s e s
F u s e N ° Rating
F u n c t i o n s
F1 20 A Engine management control unit.
F2 15 A Horn.
F3 10 A Rear electric blind.
F4 20 A Headlamp wash.
F5 15 A Fuel pump (except 2 litre HDI 16V), diesel heater (2 litre HD
I 16V), turbocharger and diesel
pre-heat unit (2.7 litre HDI 24V).
F6 10 A Power steering, suspension control unit, automatic gearbox, aut
omatic headlamp
adjustment unit.
F7 10 A ESP control unit.
F8 25 A Starter coil.
F9 10 A Coolant level sensor, passenger compartment heating (HDI), S TOP switch.
F10 30 A Engine management actuators (injectors, ignition coil, solen oid valves, oxygen sensors).
To access the fuses located in the en-
gine compartment, remove the cover
and unclip the fuse box lid.
W h e n y o u h a v e fi n i s h e d , c l o s e t h e l i d
carefully to guarantee the sealing of
t h e f u s e b o x a n d r e fi t t h e c o v e r .
Page 127 of 182
1010
109
The electrical system of your vehicle is designed to operate with standard or optional equipment.
Before installing other electrical equipment or accessories on yo ur vehicle, contact a PEUGEOT dealer.
F u s e N ° Rating
F u n c t i o n s
F11 40 A Air conditioning blower relay.
F12 30 A Wipers relay.
F13 40 A Built-in systems interface supply (ignition positive).
F14 30 A Air pump.
F15 10 A Right-hand main beam headlamp.
F16 10 A Left-hand main beam headlamp.
F17 15 A Left-hand dipped headlamp.
F18 15 A Right-hand dipped headlamp.
F19 15 A O i l v a p o u r h e a t e r ( 2 l i t r e H D I 1 6 V ) , i n l e t a i r h e a t i n g s o l e
n o i d v a l v e ( 2 l i t r e H D I 1 6 V ) , a i r fl o w
sensor (2 litre HDI 16V and 2.7 litre V6 HDI 24V), oxygen sensor .
F20 10 A Water in diesel sensor (2 litre HDI 16V) injection pump (2.7 l
itre V6 HDI 24V), turbo
regulation solenoid valve (2 litre HDI 16V).
F21 10 A Fan assembly relay control, additional fan assembly (2.7 litre V6 HDI 24V).
PEUGEOT will not accept responsibility for the cost incurred in re pairing your vehicle or for rectifying the malfunctions resulting
from the installation of accessories not supplied a nd not recommended by PEUGEOT and not installed in accordance with its
instructions, in particular when the combined consu mption of all of the additional equipment connected exceeds 10 milliamperes.
Page 128 of 182
1010
110
C H A N G I N G A W I N D S C R E E N
W I P E R B L A D E
Placing the wiper blades in the
maintenance position
Less than one minute after switching
off the ignition, press the windscreen
wiper stalk down once to position the
blades at the top of the windscreen
(maintenance position).
E N E R G Y E C O N O M Y M O D E
After the engine has stopped, certain
functions (windscreen wiper, elec-
tric windows, sunroof, electric seats,
audio equipment, telephone, dipped
headlamps, video, etc.) can only be
used for a limited combined duration,
to prevent discharging of the battery.
Once this period has elapsed, a
switching to economy mode message
appears on the multifunction display
and the active functions are put on
standby.
These functions are reactivated au-
tomatically next time the vehicle is
driven.
In order to exit the economy mode and
resume the use of these functions im-
mediately, the engine must be started
and left to run for a few minutes.
If the engine has been running for at
least 10 minutes, all of the functions
are active for 30 minutes.
If the engine has been running for
less than 10 minutes, this duration
before returning to economy mode is
5 minutes. All of these functions are
available when the engine is
running.
If the telephone is being used
when economy mode starts, it will still
b e p o s s i b l e t o fi n i s h t h e c a l l .
L O A D R E D U C T I O N F U N C T I O N
When driving, certain functions (air con-
ditioning, heated rear screen, heating
system for passenger compartment of
diesel vehicles, etc.) may be switched
off temporarily, depending on the level
of battery charge.
Reactivation of these functions is au-
tomatic, once the battery charge is
s u f fi c i e n t .
Note: at the risk of discharging the
battery, the functions that have been
switched off may be reactivated manually.
Replacing a blade
Lift the arm, then unclip the blade
and remove it.
Fit the new blade and fold down
the arm.
To reposition the blades, switch on the
ignition and operate the windscreen
wiper stalk. A fl a t b a t t e r y p r e v e n t s t h e e n -
gine from starting.
If the doors or boot are opened
several times or if the alarm is
triggered, this may result in activation
of the energy economy mode.