2009 Peugeot 407 wheel
[x] Cancel search: wheelPage 133 of 250
1010PRACTICAL INFORMATION
115
CHANGING A FRONT BULB
Handle the bulbs with a dry cloth.
2 - Main beam headlamps: H7-55 W.
Remove the protective cover cor-
responding to the faulty bulb.
Disconnect the connector.
Press the end of the securing clips
to free the bulb. Change the bulb.
W h e n fi t t i n g t h e n e w b u l b , e n s u r e t h a t
the direction notches are positioned
correctly and the securing clips are
fi x e d p r o p e r l y .
Reconnect the connector.
R e fi t t h e p r o t e c t i v e c o v e r .
4 -
Direction indicators:
PY 21 W (amber).
Turn the bulb holder a quarter turn
and remove it.
Change the bulb.
WARNING: RISK OF
ELECTROCUTION
Front lights
In the engine compartment, remove
the cover secured by one or two but-
t e r fl y s c r e w s , a p l a s t i c r e t a i n e r c l i p a n d
two quarter turn screws.
1 - Dipped beam headlamps:
H1-55 W or D2S-35 W xenon bulb.
Xenon bulbs must be replaced by a
PEUGEOT dealer. Amber coloured bulbs (direction
indicators and side repeaters)
must be replaced with bulbs
o f i d e n t i c a l s p e c i fi c a t i o n a n d
colour.
5 - Front fog lamps: H11 - 55 W.
Turn the wheels to full lock.
A c c e s s t o t h e b u l b i s v i a t h e fl a p i n t h e
f r o n t m u d fl a p .
Consult a PEUGEOT dealer.
T h e h e a d l a m p s a r e fi t t e d w i t h p o l y c a r -
bonate glass with a protective coating.
Do not clean them with a dry or abra-
sive cloth, nor with a detergent or sol-
vent product.
E n s u r e t h a t t h e l i q u i d u s e d t o fi l l t h e
wash-wipe and headlamp wash reser-
voir is of good quality.
High pressure washing :
when using a high pressure
washer on stubborn dirt, do
not persist on the headlamps,
the lights and their periphery to avoid
damaging their coating and their seal.
In certain climatic conditions (low tem-
perature, humidity), condensation on
the inside surface of the headlamp
glass and rear lights glass is normal;
it disappears a few minutes after the
lights are switched on.
3 - Side lights: W 5 W.
Remove the protective cover, dis-
connect the connector and then
remove the bulb and change it.
Put the connector back in place.
Reconnect the connector.
R e fi t t h e p r o t e c t i v e c o v e r .
Page 134 of 250
1010PRACTICAL INFORMATION
116
Integrated direction indicator side
repeaters CHANGING A REAR BULB (SALOON)
Third brake light:
Five W 5 W bulbs.
Remove the plastic cover carefully
by unclipping it at the centre and
on either side, perpendicular to its
direction of engagement.
Press on the two tabs located at
the rear, near the rear screen.
Pull the red transparent cover out-
wards while maintaining the pressure
on the tabs.
Change the faulty bulb.
W h e n r e fi t t i n g , e n s u r e t h a t t h e
tabs of the red transparent cover
are engaged correctly and that the
upper trim has been put back in
place correctly.
S c r e w o n t h e l i g h t fi x i n g n u t s i n -
side the boot using the towing eye,
i f n e c e s s a r y . W h e n r e fi t t i n g , e n -
sure that the light is positioned and
fi x e d c o r r e c t l y .
Reconnect the connector.
Number plate lights:
W 5 W.
Remove the transparent cover using
a screwdriver blade.
Change the faulty bulb.
Push the repeater forwards or
backwards and release it.
Unclip the repeater and change it.
Repeaters can be obtained from
PEUGEOT dealers.
Amber coloured bulbs (direction indi-
cators and side repeaters), must be
replaced with bulbs of identical speci-
fi c a t i o n a n d c o l o u r .
1. Direction indicators:
PY 21 W (amber).
2. Reversing lights: P21 W.
3. Fog lamps/side lights:
P21/4 W.
4. Side lights: P21/4 W.
5. Brake lights/side lights: P21/4 W.
Disconnect the connector.
U n s c r e w t h e l i g h t fi x i n g n u t s i n -
side the boot using the towing eye
(stored inside the spare wheel), if
necessary.
Remove the seal.
Unclip the bulb holder moving
aside the 5 tabs.
Unscrew the bulb and change it.
Lock the bulb holder in place.
Reposition the seal.
Page 135 of 250
1010PRACTICAL INFORMATION
116
Integrated direction indicator side
repeaters CHANGING A REAR BULB (SALOON)
Third brake light:
Five W 5 W bulbs.
Remove the plastic cover carefully
by unclipping it at the centre and
on either side, perpendicular to its
direction of engagement.
Press on the two tabs located at
the rear, near the rear screen.
Pull the red transparent cover out-
wards while maintaining the pressure
on the tabs.
Change the faulty bulb.
W h e n r e fi t t i n g , e n s u r e t h a t t h e
tabs of the red transparent cover
are engaged correctly and that the
upper trim has been put back in
place correctly.
S c r e w o n t h e l i g h t fi x i n g n u t s i n -
side the boot using the towing eye,
i f n e c e s s a r y . W h e n r e fi t t i n g , e n -
sure that the light is positioned and
fi x e d c o r r e c t l y .
Reconnect the connector.
Number plate lights:
W 5 W.
Remove the transparent cover using
a screwdriver blade.
Change the faulty bulb.
Push the repeater forwards or
backwards and release it.
Unclip the repeater and change it.
Repeaters can be obtained from
PEUGEOT dealers.
Amber coloured bulbs (direction indi-
cators and side repeaters), must be
replaced with bulbs of identical speci-
fi c a t i o n a n d c o l o u r .
1. Direction indicators:
PY 21 W (amber).
2. Reversing lights: P21 W.
3. Fog lamps/side lights:
P21/4 W.
4. Side lights: P21/4 W.
5. Brake lights/side lights: P21/4 W.
Disconnect the connector.
U n s c r e w t h e l i g h t fi x i n g n u t s i n -
side the boot using the towing eye
(stored inside the spare wheel), if
necessary.
Remove the seal.
Unclip the bulb holder moving
aside the 5 tabs.
Unscrew the bulb and change it.
Lock the bulb holder in place.
Reposition the seal.
Page 136 of 250
1010PRACTICAL INFORMATION
117
CHANGING A REAR BULB (407 SW)
Left and right fog lamps:
P21 W.
Carefully unclip the tailgate interior
trim.
Detach the sealing sheet located
behind the light concerned.
Remove the bulb holder turning it a
quarter of a turn.
Change the faulty bulb.
W h e n r e fi t t i n g , e n s u r e t h a t t h e b u l b i s
positioned correctly in the bulb holder.
Unclip the light (2 clips).
Disconnect the connector and re-
move the light.
Unclip the bulb holder moving
aside the 4 tabs.
Unscrew the bulb and change it.
Reconnect the connector.
Lock the bulb holder in place.
W h e n r e fi t t i n g i t , e n s u r e t h a t t h e
lamp is correctly positioned and
secured, reclipping the rear part
then the front part.
Number plate lights:
W 5 W.
Insert a thin screwdriver in one of
the exterior holes of the transpar-
ent cover.
Push it towards the outside to un-
clip it.
Remove the transparent cover.
Change the faulty bulb. Third brake light (diodes)
All work on the diode lights must be
carried out by a PEUGEOT dealer.
Wing lights
1. Brake lights/side lights:
P21/5 W.
2. Reversing lights:
P21 W.
3. Direction indicators:
P21 W.
These three bulbs are changed by
removing the light.
Remove the corresponding boot
s i d e fl a p t o g a i n a c c e s s t o t h e
light.
R e m o v e t h e l i g h t fi x i n g n u t i n s i d e
the boot.
Note: if necessary, use the wheelbrace
to remove the nuts. In some climatic conditions
(e.g. low temperature or hu-
midity), the presence of misting
on the internal surface of the
glass of the headlamps and rear lamps
is normal; it disappears after the lamps
have been on for a few minutes.
Page 137 of 250
1010PRACTICAL INFORMATION
118
CHANGING A FUSE
The fuse boxes are placed in the lower
part of the fascia (passenger side in
the glove box) and in the engine com-
partment (left-hand side). Fascia fuses
To access the fuses, open the glove box. Open the fuse box co
ver by pressing the
two tabs at the top.
Replacing a fuse
Before replacing a fuse, the cause of
the incident must be found and recti-
fi e d . T h e f u s e n u m b e r s a r e i n d i c a t e d
on the fuse box. Always replace a faulty fuse
with a fuse of the same rating
(same colour).
Use the special pliers located
on the support next to the fuse box,
this support also contains the replace-
ment fuses.
Fuse N°
Rating
A
Functions
F1 15 Rear wiper.
F2 30 Central locking/deadlocking.
F3 5 Air bags.
F4 10 ESP dual function sensor, diagnostic connector,
sunroof (Saloon), steering wheel angle sensor.
F5 30 Front one-touch electric windows, sunroof
( S a l o o n ) , p a n o r a m i c r o o f c o n c e a l i n g fl a p
(407SW).
F6 30 Rear one-touch electric windows.
F7 5 Glove box light, side repeaters, front and rear
courtesy lights, map reading lights, courtesy
mirror.
F8 20 Multifunction display, audio equipment, steering
wheel control, trailer fuse box, alarm control
unit, navigation-telematics (according to
country).
Page 138 of 250
1010PRACTICAL INFORMATION
118
CHANGING A FUSE
The fuse boxes are placed in the lower
part of the fascia (passenger side in
the glove box) and in the engine com-
partment (left-hand side). Fascia fuses
To access the fuses, open the glove box. Open the fuse box co
ver by pressing the
two tabs at the top.
Replacing a fuse
Before replacing a fuse, the cause of
the incident must be found and recti-
fi e d . T h e f u s e n u m b e r s a r e i n d i c a t e d
on the fuse box. Always replace a faulty fuse
with a fuse of the same rating
(same colour).
Use the special pliers located
on the support next to the fuse box,
this support also contains the replace-
ment fuses.
Fuse N°
Rating
A
Functions
F1 15 Rear wiper.
F2 30 Central locking/deadlocking.
F3 5 Air bags.
F4 10 ESP dual function sensor, diagnostic connector,
sunroof (Saloon), steering wheel angle sensor.
F5 30 Front one-touch electric windows, sunroof
( S a l o o n ) , p a n o r a m i c r o o f c o n c e a l i n g fl a p
(407SW).
F6 30 Rear one-touch electric windows.
F7 5 Glove box light, side repeaters, front and rear
courtesy lights, map reading lights, courtesy
mirror.
F8 20 Multifunction display, audio equipment, steering
wheel control, trailer fuse box, alarm control
unit, navigation-telematics (according to
country).
Page 147 of 250
1010PRACTICAL INFORMATION
125
Without lifting
(4 wheels on the ground)
You must always use a towbar.
The removable towing eye is inside
the spare wheel.
At the front and at the rear:
Unclip the cover,
Screw in the towing eye as far as it
will go. Special features of the
automatic gearbox
When towing with the engine switched
off, there is no braking or steering
assistance.
Failure to observe this special require-
ment may lead to the destruction of
certain braking units and the absence
of braking assistance when the engine
is re-started.
TOWING YOUR VEHICLE
Lifting
(2 wheels only on the ground)
It is preferable to raise the vehicle with
a professional lifting device.
Place the gear lever in neutral
(position N in the case of the
automatic gearbox).
Towing a vehicle with an auto-
matic gearbox in reverse gear
is prohibited (absence of lubri-
cation). When towing with four wheels on the
ground, the following rules must be
obeyed:
- lever in position
N ,
- tow the vehicle at less than 30 mph (50 km/h) over a maximum dis-
tance of 30 miles (50 km).
- do not add oil to the gearbox.
Page 150 of 250
1010PRACTICAL INFORMATION
128
ACCESSORIES FOR YOUR 407
A wide range of accessories recom-
mended by PEUGEOT and original
parts are offered by the Network.
They all benefit from PEUGEOT recommendation.
These accessories and parts, having
been tested and approved for reliability
and safety, are all adapted to your
PEUGEOT vehicle.
The product range offered by PEUGEOT Accessories is structured
around 5 categories: PROTECTION -
TOURING - IN-CAR TECHNOLOGY -
STYLING - UNIVERSAL. Anti-theft alarm, parking as-
sistance, engraved windows,
w h e e l a n t i - t h e f t d e v i c e s , fi r s t
aid kit, warning triangle, high
visibility safety jacket, snow
chains, anti-skid covers, dog
guard, etc.
"Protection": Seat covers compatible with
side air bags, mats, boot
tray.
For leisure pursuits: roof bars, transportation acces-
sories (bicycle carrier, ski
carrier), roof box, child seats and
booster cushions, rear screen blind,
audio/telephone console, side blinds,
cool box.
T r a i l e r t o w b a r w h i c h m u s t b e fi t t e d b y
the PEUGEOT Network.
"Touring":
Telephone, hands-free kits,
satellite navigation, CD changer, multimedia, connec-
tion for portable MP3 player
(in the glove box), USB Box.
"In-Car Technology": Alloy wheels, wheel trims,
spoiler, leather steering wheel,
styling strips, door spoilers,
stainless steel sill protectors.
"Styling":
W i n d s c r e e n w a s h fl u i d , i n t e -
rior and exterior cleaning and
maintenance products.
"Universal":
T h e fi t t i n g o f e l e c t r i c a l e q u i p m e n t or accessories which are not
recommended by PEUGEOT
may result in a failure of your
vehicle's electronic system.
P l e a s e n o t e t h i s s p e c i fi c w a r n i n g . Y o u
are advised to contact a representa-
tive of the Marque to be shown the
range of recommended equipment
and accessories.
Note
To avoid any jamming under the pedals:
- ensure that the mat is positioned
and secured correctly,
- never place one mat on top of another.
Depending on the country in
which the vehicle is sold, it
is compulsory to have a high
visibility safety jacket, warning
triangle and spare bulbs available in the vehicle.
Installation of radiocommunication
transmitters
It is advisable to contact a representa-
tive of the PEUGEOT marque before
installing accessory radiocommunica-
tion transmitters with external aerial
on your vehicle. The PEUGEOT Network will inform
y o u o f t h e s p e c i fi c a t i o n s ( f r e q u e n c y
waveband, maximum output power,
a e r i a l p o s i t i o n , s p e c i fi c i n s t a l l a t i o n
conditions) of the transmitters which
c a n b e fi t t e d , i n a c c o r d a n c e w i t h t h e
Motor Vehicle Electromagnetic Com-
patibility Directive (2004/104/EC).
407 SW: you can obtain "Van" con-
version kits to convert from a private
vehicle to a van.