2009 Peugeot 308 CC ignition

1
!
23
INSTRUMENTS and CONTROLS
The warning lights may come on continuously or fl ash.
Certain warning lights may come on in two different modes. Only by relating the type of lighting to the operating status of the vehicle can it be ascertained whether the situa-tion is normal or whether a fault has occurred.
Indicator and warning lights
Visual indicators informing the driver that a system is in operation (operation or deactivation indicator lights) or of the occurrence of a fault (warning light).
Associated warnings
The switching on of certain warninglights may be accompanied by an audible signal and a message on the multifunction display.
Operation indicator lights
If one of the following indicator lights comes on, this confi rms that the corre-sponding system has come into operation.
Left-hand direction indicator.
Handbrake applied.
Right-hand direction indicator.
Main beam headlamps.
Dipped headlamps.
Diesel engine pre-heating .
Wait until this goes off before
operating the starter.
Front fog lamps.
Rear fog lamp.
When the ignition is switched on
The warning lights come on for a few seconds when the vehicle's ignition is switched on.
When the engine is started, these war-ning lights should switch off.
If they remain on, before moving off, consult the warning light concerned.
Common operation indicator lights

1
32
INSTRUMENTS and CONTROLS
Service indicator
System which informs the driver when the next service is due, in accord-ance with the manufacturer's servicing schedule.
The point at which the service is due is calculated from the last indicator zero reset. It is determined by two param-eters:
- the distance travelled,
-the time elapsed since the last service.
Between 600 miles (1 000 km) and 1 800 miles (3 000 km) remain before the next service is due
For 5 seconds after the ignition is switched on, the spanner symbolising the service operations comes on. The distance re-corder display line indicates the distance remaining before the next service is due.
Example: 2 800 km remain before the next service is due.
For 5 seconds after the ignition is switched on, the display indicates:
5 seconds after the ignition is switched on, the spanner is switched off ; the switched offdistance recorder resumes its normal operation. The display then indicates the total and trip distances.
Less than 600 miles (1 000 km) remain before the next service is due
Example: 900 km remain before the next service is due.
For 5 seconds after the ignition is switched on, the display indicates:
5 seconds after the ignition is switched on, the distance recorder resumes its normal operation. The spanner remains on to indicate that a service must be car-ried out soon.
More than 1 800 miles (3 000 km) remain before the next service is due
When the ignition is switched on, no service information appears on the display.

1
i
i
33
INSTRUMENTS and CONTROLS
Following this operation, if you wish
to disconnect the battery, lock the
vehicle and wait at least fi ve minutes
for the zero reset to be taken into
account.
Maintenance indicator zero reset
After each service, the maintenance in-
dicator must be reset to zero.
The procedure for resetting to zero is as
follows:

 switch off the ignition,

 press and hold the trip distance
recorder zero reset button,

 switch on the ignition; the
distance recorder display begins a
countdown,

 when the display indicates "=0" ,
release the button; the spanner
disappears.
The distance remaining may be weighted by the time factor, depend-ing on the driver's driving habits.
Therefore, the spanner may also come on if you have exceeded the two year service interval.
Service overdue
For 5 seconds after the ignition is switched on, the spanner fl ashes to in-dicate that the service must be carried out as soon as possible.
Example: the service is overdue by 300 miles (km).
For 5 seconds after the ignition is switched on, the display indicates:
5 seconds after the ignition is switched on, the distance recorder resumes its normal operation. The spanner re-mains lit .
Retrieving the service information
You can access the service information
at any time.

 Press the trip distance recorder zero
reset button.
The service information is displayed for a few seconds, then disappears.

1
i
34
INSTRUMENTS and CONTROLS
The level read will only be correct if
the vehicle is on level ground and
the engine has been off for more
than 15 minutes.
Engine oil level indicator
System which informs the driver of the
validity or invalidity of the engine oil
level.
This information is indicated for a few
seconds when the ignition is switched
on, after the service information.
Oil level correct
Lack of oil Oil level gauge fault
Dipstick
This is indicated by the fl ashing of "OIL" ,
linked with the service warning light,
accompanied by an audible signal and a
message on the multifunction display.
If the lack of oil is confi rmed by a check
using the dipstick, it is essential that the
level is topped up to prevent damage to
the engine. This is indicated by the fl ashing of "OIL--" .
Consult a PEUGEOT dealer.
Refer to the "Checks" section to locate
the dipstick and the oil fi ller cap on your
engine.
There are 2 marks on the
dipstick:
- A = max; never exceed
this level (risk of
damage to the engine),
- B = min; top up the
level via the oil fi ller
cap, using the type
of oil suited to your
engine.

1
35
INSTRUMENTS and CONTROLS
Total distance recorder
System which measures the total distance
travelled by the vehicle during its life. Lighting rheostat
System for manual adjustment of the
brightness of the instruments and con-
trols in relation to the exterior brightness.
The total and trip distances are dis-
played for thirty seconds when the igni-
tion is switched off, when the driver's
door is opened and when the vehicle is
locked or unlocked. Trip distance recorder
System which measures a distance
travelled during a day or other period
since it was reset to zero by the driver.

 With the ignition on, press the button
until zeros appear. Activation
When the lights are on:

 press the button to change the
brightness of the instruments and
controls,

 when the lighting reaches the mini- mum setting, release the button,
then press again to increase it,
or

 when the lighting reaches the maxi-
mum setting, release the button, then
press again to reduce it,


when the lighting reaches the level
of brightness required, release the
button.
Deactivation
When the lights are off, or in day mode
on vehicles fi tted with daytime lights,
pressing the button does not have any
effect.

2
i
i
43
MULTIFUNCTION DISPLAYS
Access to the retractable screen
Opening the screen

 With the screen stored, press
control A to open it.
The screen opens automatically when
the ignition is switched on, when the
audio and telematics system is switched
on, when an outgoing telephone call
is made, when a voice command is
given and when a warning message
linked with the STOP warning light is
received.
This screen is opened and stored auto-
matically.
However, you can also open it, store it
and adjust it using the various manual
controls:
- opening or storing by means of
control A ,
- angle adjustments by means of control B .
It is also fi tted with safety auto-reverse
protection. Closing the screen

 With the screen open, press con-
trol A to store it.
The screen is stored automatically when
the ignition is switched off, after approxi-
mately three seconds, if the audio and
telematics system is off.
If you wish the screen to open or
close automatically when the audio
and telematics system is switched
on or off, the screen must not be
closed when the audio and telema-
tics system is operating. When the screen is open, you can
adjust it precisely in different ways:

 press the corresponding part of
control B to move the screen towards
you or towards the windscreen,
or

 push or pull the screen gently by hand.
Adjusting the position of the screen
Safety auto-reverse
If the screen meets an obstacle as it
opens or closes, the movement stops
immediately and is reversed by a few
millimetres.
After clearing the obstacle, issue the
command required again. Storing the position of the screen
The system has four pre-set positions
in its memory.
Each time the screen is closed, the
system stores the last position of the
screen.
Each time the screen is re-opened, the
system returns the screen to the pre-set
position closest to that stored.
If you close the screen during opera-
tion of the audio and telematics sys-
tem, it will only re-open automatically
when an outgoing telephone call is
made, when a voice command is
given or when a warning message
linked with the STOP warning light is
received.

3
i
56
COMFORT
FRONT SEATS
Seat consisting of a seat cushion and
a seat back which can be adjusted to
adapt your position for ease of driving
and comfort.
Forwards-backwards adjustment
 Push the control forwards or rear-
wards to slide the seat. Seat cushion height and angle
adjustment  Tilt the rear part of the control up-
wards or downwards to obtain the
required height.
 Tilt the front part of the control up-
wards or downwards to obtain the
required angle. Seat back angle adjustment
 Tilt the control forwards or rearwards
to adjust the angle of the seat back.
Electric adjustments
The electrical functions of the seat are
deactivated approximately one minute
after the ignition is switched off.
To reactivate them, switch on the
ignition.

3
i
!
!
59
COMFORT
Storing driving positions
System which takes into account the
electrical settings of the driver's seat
and exterior mirrors. It enables you to
store up to two positions using the but-
tons on the side of the driver's seat and
two further driving positions using the
two remote control keys. Recalling a stored position
Storing a position Storing a new position cancels the
previous position.
When the ignition is off, after a few
consecutive position recalls, the
function will be deactivated until
the engine is started, to prevent
discharging of the battery.
Using the remote control keys
When the vehicle is locked, the remote
control key stores the position of the
driver's seat and exterior mirrors.
Each remote control key can store one
specifi c setting.
Using buttons M/1/2
 Press and hold button
1 or 2 until
the audible signal is heard indi cating
the end of the adjustment.
Using the remote control keys
When the vehicle is unlocked, the
driver's seat and the exterior mirrors
return to the position stored by the
remote control key.
Using buttons M/1/2
 Switch on the ignition.
 Adjust your seat and your exterior
mirrors.
 Press button
M , then press button 1
or 2 within four seconds.
An audible signal is heard indicating that the storing has been taken into
account.
REAR SEATS
Fixed two-seat bench fi tted with roll-
over bars to guarantee your protection
should the vehicle roll over.
Do not place any covering on
the rear head restraints. Use a
special cover recommended by the
PEUGEOT network.
The rear head restraints are fi xed and
cannot be adjusted. They incorporate
the roll-over hoops (refer to the section
"Safety - § Roll-over hoops").
The rear bench seat may be fi tted with a
retractable comfort armrest in the centre
of the seat back.