2009 Peugeot 207 Dag cruise control

18
PETROL - DIESEL MANUAL GEARBOX OR "2 TRONIC" OR
AUTOMATIC GEARBOX INSTRUMENT PANELS
Panel which groups together the vehicle
operation dials and indicator lights.
5. Display.

6. Display zero reset button.
Resets the selected function to zero (trip distance recorder or service in-
dicator).

7. Instrument panel lighting button.
Adjusts the brightness of the lighting of the instruments and controls.

8. " 2 Tronic " or automatic gearbox.
Indicates the programme selected and the gear engaged.
Dials

1. Rev counter.
Indicates the speed of rotation of the engine (x 1 000 rpm).

2. Fuel gauge.
Indicates the quantity of fuel remain- ing in the tank.

3. Cooling temperature.
Indicates the temperature of the en- gine coolant (° Celsius).

4. Speedometer.
Indicates the current speed of the moving vehicle (km/h or mph).
A. Speed limiter.
or
Cruise control.
(km/h or mph)

B. Trip distance recorder.
(km or miles)

C. Service indicator.
(km or miles) then,
Engine oil level indicator.
then
Distance recorder.
(km or miles)
These three functions are displayed in succession when the ignition is
switched on.
Display
For further information, refer to the sec-
tion which corresponds to the function
and to the display associated with it.

i
126
CRUISE CONTROL
System which automatically maintains the speed of the vehicle at the value programmed by the driver, without any action on the accelerator pedal.
The cruise control is switched onmanually: it requires a minimum vehicle speed of 25 mph (40 km/h), as well as the engaging:
- of fourth gear on the manual gear-box,
- of second gear with the "2 Tronic" or automatic gearbox, in sequential mode,
- of position A on the "2 Tronic" gear-box or D on the automatic gearbox.
The cruise control is switched off manu- offally or by pressing the brake or clutch pedal or on triggering of the ESP sys-tem for safety reasons.
It is possible to exceed the programmed speed temporarily by pressing the ac-celerator pedal.
To return to the programmed speed, simply release the accelerator pedal.
Switching off the ignition cancels any programmed speed value.
The controls of this system are grouped together on lever A .
1. Cruise control mode selection dial
2. Value decrease button
3. Value increase button
4. Cruise control off/resume button
The programmed information is grouped together on the instrument panel dis-play.
5. Cruise control off/resume indication
6. Cruise control mode selection indication
7. Programmed speed value
Steering wheel controls Displays on the instrument panel

!
127
Programming
 Turn dial 1 to the "CRUISE" po-sition: the cruise control mode is selected but is not switched on (OFF).
Exceeding the programmed speed
Intentional or unintentional exceeding of the programmed speed results in fl ashing of this speed on the display.
Return to the programmed speed, by means of intentional or unintentional deceleration of the vehicle, automatically can-cels the fl ashing of the speed.
Return to normal driving
Turn dial 1 to the "0" position: the cruise control mode is deselected. The display returns to the distance recorder.
Operating fault
In the event of a cruise control mal-function, the speed is cleared result-ing in fl ashing of the dashes. Contact a PEUGEOT dealer to have the system checked.
 Set the programmed speed by ac-celerating to the required speed, then press button 2 or 3 (e.g.: 70 mph (110 km/h)).
 Switch off the cruise control by pressing button 4 : the display confi rms that it has been switched off (OFF).
 Switch the cruise control back on by pressing button 4again.
You can then change the programmed speed using buttons 2 and 3 :
- by + or - 1 mph (km/h) = short press,
- by + or - 5 mph (km/h) = long press,
- in steps of + or - 5 mph (km/h) = maintained press.