2009 Peugeot 207 Dag ECO mode

!
19
Indicator and warning lamps
Visual indicators informing the driver that a system is in operation (operation or
deactivation indicator lamps) or of the occurrence of a fault (wa rning lamp).
When the ignition is switched on
Certain warning lamps come on for a few seconds when the vehi cle's ignition is
switched on.
When the engine is started, these same warning lamps should switch off.
If they remain on, before moving off, refer to the informati on on the warning lamp
concerned.
Associated warnings
The switching on of certain warning lamps may be accompanied b y an audible
signal and a message on the multifunction screen. The warning lamps may come on
continuously (fi xed) or fl ash.
Certain warning lamps may come
on in two different modes. Only by
relating the type of lighting to the
operating status of the vehicle can
it be ascertained whether the situ-
ation is normal or whether a fault
has occurred.
Operation indicator lamps
If one of the following indicator lamps comes on, this confi rms that the correspond-
ing system has come into operation.

Warning lamp is on Cause Action/Observations

Left-hand
direction
indicato
r fl ashing with
buzzer. The lighting stalk is pressed
down.


Right-hand
direction
indicator fl ashing with
buzzer. The lighting stalk is pushed
up.


Dipped beam
headlamps fi xed. The lighting stalk is in the
"Dipped beam headlamps"
position. Turn the control to the desired position

Main beam
headlamps fi xed. The lighting stalk is pulled
towards you. Pull the stalk to return to dipped beam
headlamps.

30
Total distance recorder
System which measures the total dis-
tance travelled by the vehicle during its
life. Lighting rheostat
System for manual adjustment of the bri-ghtness of the instruments and controls in relation to the exterior brightness.
CLOCK
Integrated system which displays the time with independent setting of the hours and minutes.
The total and trip distances are dis-
played for thirty seconds when the ig-
nition is switched off, when the driver's
door is opened and when the vehicle is
locked or unlocked.
Trip distance recorder
System which measures a distance
travelled during a day or other period
since it was reset to zero by the driver.

 With the ignition on, press the but-
ton until zeros appear. Activation
When the lights are on:  press the button to change the bri-ghtness of the instruments and controls,  when the lighting reaches the mi-nimum setting, release the button, then press again to increase it, or  when the lighting reaches the maxi-mum setting, release the button, then press again to reduce it, when the lighting reaches the level of brightness required, release the button.
Deactivation
When the lights are off, or in day mode on vehicles fi tted with daytime lights, pres-sing the button does not have any effect.
Setting
 Press the corresponding button briefl y to obtain slow scrolling.
or
Continue to press the correspondingbutton to obtain rapid scrolling.
Button 1 : setting of the hours.
Button 2 : setting of the minutes.

!
32
Options
Once the "Options" menu has been se-
lected, you can start diagnostics of the
status of the equipment (active, not ac-
tive, faulty). Languages
Once the "Languages" menu has been
selected, you can change the language
used by the display (Français, Italiano,
Nederlands, Portugues, Portugues-
Brasil, Deutsch, English, Espanol).
Display settings
Once the "Display settings" menu has
been selected, you can gain access to
the following settings:
- year,
- month,
- day,
- hour,
- minutes,
- 12 or 24 hour mode.

 Wait for approximately ten sec-
onds without any action to allow the
changed data to be recorded or press
the "ESC" button to cancel.
The display then returns to the normal
display.
Once the "Vehicle confi guration" menu
has been selected, you can activate or
deactivate the following equipment:
- wiper linked with reverse gear (refer to the "Visibility" section),
- directional headlamps (refer to the "Visibility" section),
- "follow-me-home" lighting (refer to the "Visibility" section).
For safety reasons, it is imperative
that confi guration of the multifunc-
tion displays by the driver takes
place when stationary.
Units
Once the "Units" menu has been se-
lected, you can change the units of the
following parameters:
- temperature (°C or °F),
- fuel consumption (l/100km, mpg or
km/l).
Vehicle confi guration

 Once you have selected a setting,
press the "OK" button to change its
value.

!
34
For safety reasons, it is imperative
that confi guration of the multifunc-
tion displays by the driver takes
place when stationary.
Display settings
Once the "Display settings" menu has
been selected, you can gain access to
the following settings:
- year,
- month,
- day,
- hour,
- minutes,
- 12 or 24 hour mode.
Languages
Once the "Languages" menu has been
selected, you can change the language
used by the display (Français, Italiano,
Nederlands, Portugues, Portugues-
Brasil, Deutsch, English, Espanol).
Units
Once the "Units" menu has been se-
lected, you can change the units of the
following parameters:
- temperature (°C or °F),
- fuel consumption (l/100km, mpg or km/l).

 Once you have selected a setting,
press the "  " or "  " buttons to
change its value.

 Press the "  " or "  " buttons to
switch respectively to the previous
or next setting.

 Press the "OK" button to record the
change and return to the normal dis-
play or press the "ESC" button to
cancel.
Vehicle confi guration
Options
Once the "Options" menu has been se-
lected, you can start diagnostics of the
status of the equipment (active, not ac-
tive, faulty).
Once the "Vehicle Confi guration" menu
has been selected, you can activate or
deactivate the following equipment:
- wiper linked with reverse gear (refer
to the "Visibility" section),
- directional headlamps (refer to the "Visibility" section),
- "follow-me-home" lighting (refer to the "Visibility" section).

i
i
52
When the engine is cold, to prevent
too great a distribution of cold
air, the air fl ow will only reach its
optimum level gradually. The air conditioning can only operate with the engine running.
The driver and his front
passenger can each set
the temperature to suit their
requirements.
 Turn dial 2 or 3 to the left to reduce
the value or to the right to increase it.
A setting around 21 enables you to
obtain an optimum level of comfort.
Depending on your requirements, a
setting between 18 and 24 is usual.
In addition, it is recommended that you avoid a left/right setting difference of more than 3.
4. Automatic visibility programme
The automatic comfort pro-
gramme may not be suffi cient
to quickly demist or de-ice the
windscreen and side windows
(humidity, several passengers,
ice...).

 In this case, select the automatic vis-
ibility programme.
The system automatically controls the
air conditioning, the air fl ow and the air
intake and provides optimum distribution
of the ventilation to the windscreen and
side windows.
Automatic operation  Press the "AUTO" button. The "AUTO" symbol is dis-played. 2. Driver's side adjustment
DUAL ZONE AUTOMATIC AIR CONDITIONING
We recommend that you use this mode: it provides optimised automatic control of all of the functions, passenger compartment temperature, air fl ow, air distribution and air recirculation, in accordance with the comfort value that you have selected.
This system is designed to operate
effectively in all seasons, with the
windows closed. The value indicated on the display corresponds to a level of comfort and not to a temperature in degrees Celsius or Fahrenheit.
1. Automatic comfort programme
3. Passenger side adjustment

i
i
i
ACCESS
76
WINDOW MECHANISMS Electric windows In the event of unwanted opening of
the window on closing (for example
in the presence of frost):

 press the switch until it opens
completely,

 then pull it immediately until it
closes.

 continue to hold the switch for
approximately one second after
the window has closed.
One-touch electric windows
There are two methods of
operation:
- manual mode

 Press or pull the switch gently.
The window stops as soon as the
switch is released.
- automatic mode

 Press or pull the switch fully. The
window opens or closes complete-
ly when the switch is released.

 Pressing the switch again stops
the movement of the window.
 Press or pull the switch. The window stops as soon as the switch is released.
System which opens or closes a window
manually or automatically. It is fi tted with
a system which provides protection if an
obstacle is detected on the one-touch
models and a deactivation system to
prevent misuse of the rear switches on
all models.

1. Driver's electric window switch.

2.
Passenger's electric window switch.

3. Rear right electric window switch.

4. Rear left electric window switch.
5. Disarming of the rear electric window switches.
Safety auto-reverse
In automatic mode, when the window
rises and meets an obstacle, it stops
and partially lowers again.

!
87
In fog or snow, the brightness
sensor may detect suffi cient light.
Therefore, the lights will not come
on automatically.
Do not cover the brightness sen-
sor, coupled with the rain sensor
and located in the centre of the
windscreen behind the interior mir-
ror; the associated functions would
no longer be controlled.
Coupling with the "Follow-me-
home" lighting
Association with the automatic lighting
provides the "follow-me-home" lighting
with the following additional options:
- selection of the duration of main-
taining of the lighting for 15, 30 or
60 seconds in the vehicle param-
eters on the multifunction display
confi guration menu,
- automatic activation of "follow-me- home" lighting when automatic light-
ing is in operation.
Automatic lighting
The side lights and dipped headlamps
are switched on automatically, without
any action on the part of the driver,
when a low level of external light is de-
tected (sensor behind the interior mir-
ror) or when the windscreen wipers are
switched on.
As soon as the brightness returns to a
suffi cient level or after the windscreen
wipers are switched off, the lights are
switched off automatically.
"Follow-me-home" lighting
porarily, after switching off the vehicle's ignition, to make the driver's exit easier in poor light.
Activation
 With the ignition off, activate a "headlamp fl ash" using lever B .
 A second "headlamp fl ash" switches the function off again.
Switching off
The "follow-me-home" lighting is switched off automatically following the door locking command, after a given time.
Activation

 Turn ring A to the " AUTO
" position.
The automatic lighting is accompa-
nied by a message on the multifunc-
tion display. Operating fault
In the event of a malfunction of
the brightness sensor, the lights
come on accompanied by the
service warning light, an audi-
ble signal and a message on the multi-
function display.
Have it checked by a PEUGEOT dealer.
Daytime lights *
On vehicles fi tted with daytime lights, the dipped headlamps come on when the vehicle is started.
This indicator light comes on on the instrument panel.
The instruments and controls (instru-ment panel, multifunction display, air conditioning control panel, ...) are not lit, unless the automatic switching on of the lights mode is activated or the lights are switched on manually.
Deactivation

 Turn ring A to a position other than
"
AUTO " . Deactivation is accompa-
nied by a message on the multifunc-
tion display.
* According to country.

!
87
In fog or snow, the brightness
sensor may detect suffi cient light.
Therefore, the lights will not come
on automatically.
Do not cover the brightness sen-
sor, coupled with the rain sensor
and located in the centre of the
windscreen behind the interior mir-
ror; the associated functions would
no longer be controlled.
Coupling with the "Follow-me-
home" lighting
Association with the automatic lighting
provides the "follow-me-home" lighting
with the following additional options:
- selection of the duration of main-
taining of the lighting for 15, 30 or
60 seconds in the vehicle param-
eters on the multifunction display
confi guration menu,
- automatic activation of "follow-me- home" lighting when automatic light-
ing is in operation.
Automatic lighting
The side lights and dipped headlamps
are switched on automatically, without
any action on the part of the driver,
when a low level of external light is de-
tected (sensor behind the interior mir-
ror) or when the windscreen wipers are
switched on.
As soon as the brightness returns to a
suffi cient level or after the windscreen
wipers are switched off, the lights are
switched off automatically.
"Follow-me-home" lighting
porarily, after switching off the vehicle's ignition, to make the driver's exit easier in poor light.
Activation
 With the ignition off, activate a "headlamp fl ash" using lever B .
 A second "headlamp fl ash" switches the function off again.
Switching off
The "follow-me-home" lighting is switched off automatically following the door locking command, after a given time.
Activation

 Turn ring A to the " AUTO
" position.
The automatic lighting is accompa-
nied by a message on the multifunc-
tion display. Operating fault
In the event of a malfunction of
the brightness sensor, the lights
come on accompanied by the
service warning light, an audi-
ble signal and a message on the multi-
function display.
Have it checked by a PEUGEOT dealer.
Daytime lights *
On vehicles fi tted with daytime lights, the dipped headlamps come on when the vehicle is started.
This indicator light comes on on the instrument panel.
The instruments and controls (instru-ment panel, multifunction display, air conditioning control panel, ...) are not lit, unless the automatic switching on of the lights mode is activated or the lights are switched on manually.
Deactivation

 Turn ring A to a position other than
"
AUTO " . Deactivation is accompa-
nied by a message on the multifunc-
tion display.
* According to country.