2009 Peugeot 206 P Dag lights

i
51
Automatic windscreen wipers
In the AUTO position, the windscreen
wipers operate automatically and adapt
their speed to the intensity of the
rainfall .
Operating check

Activation
Activation of the function is accompa-
nied by a message on the multi-function
display.

In the event of malfunction , the driver
is informed by an audible signal.
In the AUTO position, the windscreen
wiper will operate in intermittent mode.
Contact a PEUGEOT dealer to have the
system checked.
Do not cover the rain sensor located on
the windscreen behind the interior mirror.
When using an automatic car wash,
switch off the ignition or check that the
wiper stalk is not in the AUTO position.
In winter, it is advisable to wait for the
windscreen to completely clear of ice
before operating the automatic wipe.

Windscreen wash
Pull the wiper stalk towards you. The
windscreen wash, then the windscreen
wipers, operate for a specifi ed time. Rear screen wiper
Turn ring
A to the fi rst notch for intermit-
tent wiping.

If the ignition is switched off, it is
necessary to reactivate the control
each time . To do this, move the stalk
to any position, then move it back to the
required position.
Automatic rear screen wiper
When the windscreen wipers control is
activated and you engage reverse gear,
the rear screen wiper operates intermit-
tently.
Rear screen wash
Turn ring A past the fi rst notch; the
screen wash then the wiper operate for
a fi xed period. If you use a bicycle carrier, con-
sult a PEUGEOT dealer to have
this function deactivated or install
a specifi c bicycle carrier approved
by PEUGEOT.
COURTESY LIGHTS
System for selecting and controlling the
various passenger compartment lights.
Front courtesy light (button A)
- when the vehicle is unlocked,
- when a door is opened,
- when the ignition is switched off.
It switches off when the vehicle is
locked.
It fl ashes while driving if a door is not
closed correctly.
Permanently off.
Permanently on, when the key
is in the accessories position or
with the ignition on.
In this position, the courtesy
light comes on for approximately
30 seconds:

ii
SAFETY
52
DIRECTION INDICATORS
Selection of the left or right direction in-
dicators to signal a change of direction
of the vehicle.

 Lower the lights stalk when moving
to the left.

 Raise the lights stalk when moving
to the right.
HAZARD WARNING LAMPS
A visual warning by means of the direc-
tion indicators to alert other road users to
a vehicle breakdown, towing or accident.
As a safety precaution in a traffi c jam,
switch on the hazard warning lamps
if you are the last in the queue.

 Press the button, the direction indi-
cators fl ash.
They can operate with the ignition off.
Automatic lighting of hazard
warning lamps
When braking in an emergency, de-
pending on the deceleration, the hazard
warning lamps come on.
They will switch off automatically the
fi rst time you accelerate.

 If they do not, press button A to
switch the direction indicators off.
HORN

 Press one of the spokes of the
steering wheel.
Use the horn moderately and only
in the following cases:
- immediate danger,
- when passing a cyclist or pe- destrian,
- when approaching an area where there is no visibility.
Audible warning to alert other road
users to an imminent danger.

i
76
CHANGING A BULB
Front lights

1. Direction indicators
(PY21 W amber).

2. Side lights (W 5 W).

3. Dipped headlamps (H7-55 W).

4. Main beam headlamps (H1-55 W).

5. Fog lamps (PSX-24 W).
Operating procedure for replacing a
faulty bulb with a new bulb. These
operations must be carried out
with the
ignition off .
To gain access to the bulbs on the right-
hand side:
- Remove the screenwash reservoir fi ller tube.
- Unclip the engine harness 1 .
- Remove the nut from the engine control unit support 2 using a size
10 spanner.
- Remove the engine control unit and support assembly. After changing the faulty bulb:
- Slide the two lugs of the control unit
support into the locations A .
- Put the engine control unit back in place.
- Tighten the engine control unit sup- port nut (size 10 spanner).
- Reclip the engine harness.
These bulbs are available from
PEUGEOT dealers.
In certain climatic conditions (low
temperature, humidity), conden-
sation inside the glass of the
headlamps and lights is normal .
However, contact a PEUGEOT
dealer if water is present in the
headlamps.

i
77

 Turn the bulb holder a quarter turn
and remove it.

 Pull the bulb and change it.
To refi t, carry out these operations in
reverse order.
Amber coloured bulbs, such as
the direction indicators, must be
replaced with bulbs of identical
specifi cation and colour.
Direction indicators

 Disconnect the headlamp main con-
nector, pulling the red control.

 Remove the plastic protective cover
turning it a quarter turn.

 Pull the bulb and change it. Dipped headlamps

 Disconnect the headlamp main con-
nector, pulling the red control.

 Remove the plastic protective cover
turning it a quarter turn.

 Press the connector downwards to
release the bulb.

 Pull the bulb and change it.
To refi t, carry out these operations in re-
verse order.
Side lights

!
78
Front fog lamp

 Slide a hand under the bumper.

 Turn the connector a quarter turn
and remove the assembly.

 Remove the bulb and change it.
Main bean headlamps

 Disconnect the headlamp main con-
nector, pulling the red control.

 Remove the plastic protective cover
turning it a quarter turn.

 Move aside the springs to release
the bulb and pull the bulb.
To refi t, carry out these operations in
reverse order. Direction indicator side repeater

 Push the repeater forwards and
release it.

 Remove the repeater and change it.
Repeaters can be obtained from a
PEUGEOT dealer.

High pressure washing
When using this type of washing
on stubborn dirt, do not persist
on the headlamps, the lights and
their surround to avoid damaging
their coating and their seal.

79
Third brake light 5 bulbs W 5 W
Unclip the boot side trim.
Remove the wing nut.
Release the light unit from the outside.
Press the lug A and disconnect the con-
nector.
Remove the sealing foam.
Move aside the tabs B and remove the
bulb holder.
Turn the faulty bulb a quarter turn and
change it.
To refi t, carry out these operations in
reverse order and ensure that the bulb
holder, the light and the foam cover are
repositioned correctly. Using a 10 mm spanner, unscrew the
2 nuts
A .
Release the light unit.
Squeeze the two tabs B to release the
bulb holder.
Change the faulty bulb.

1. Direction indicators
(P21 W amber).

2. Reversing lights P21 W.

3. Brake lights/side lights
(P21/5 W).

4. Fog lamp (P21 W).
Rear lights

80
Rear fog lamp (P21 W)
The fog lamp is located on the rear
bumper, on the left-hand side.
Unscrew the lamp and release the as-
sembly.
Turn the pin connector a quarter turn
and remove it.
Change the bulb. Number plate lights W 5 W
Insert a thin screwdriver into one of the
outer holes of the transparent cover.
Push it outwards to unclip it.
Remove the transparent cover.
Change the faulty bulb.

!i
86
ECONOMY MODE FUNCTION
After the engine has stopped, with the
key in the accessories position, cer-
tain functions (windscreen wiper, cour-
tesy lights, audio equipment, dipped
headlamps, etc.) can only be used for
a maximum cumulative duration of ap-
proximately fi fteen minutes, to prevent
discharging of the battery.
Once the fi fteen minutes are over, the
message "Economy mode active" ap-
pears on the multifunction display and
the active functions are put on standby.
These functions will be reactivated au-
tomatically the next time the vehicle is
used.
To resume the use of these functions
immediately, start the engine and let it
run for a few minutes.
The time available will then be double
the time for which the engine is left run-
ning. However, this time will always be
between fi ve and fi fteen minutes.
A fl at battery will prevent the en-
gine from starting.
TOWING THE VEHICLE
Procedure for having your vehicle towed.
Towing your vehicle


On the front bumper, unclip the cover A
to gain access to the towing eye.

 Switch on the hazard warning lights
on the towed vehicle.

 Place the gear lever in neutral. Towing another vehicle
Failure to comply with this special
requirement may result in damage
to certain braking components and
the absence of braking assistance
the next time the engine is started.