2009 Peugeot 206 P Dag buttons
[x] Cancel search: buttonsPage 39 of 113
i
40
KEYS
Central locking and unlocking
From the front doors, the keys allow you
to lock and unlock the doors and boot.
If one of the doors is open, the central
locking does not work.
If the boot is open, the central locking
works.
Remote control
This carries out the same functions as
the key, from a distance. Locking
Press button
A to lock the vehicle.
T h i s i s c o n fi r m e d b y fi x e d l i g h t i n g o f t h e
d i r e c t i o n i n d i c a t o r s f o r a p p r o x i m a t e l y
two seconds.
Unlocking
Press button B to unlock the vehicle.
T h i s i s c o n fi r m e d b y r a p i d fl a s h i n g o f
the direction indicators. Starting the vehicle
Steering lock
Before starting, unlock the steering, if
necessary, by turning the steering wheel
slightly while turning the key.
It is advisable to release the clutch dur-
ing the action of the starter to facilitate
the starting of the engine.
There are four possible positions of the
key in the ignition switch:
1. STOP position:
the ignition is off.
2. 1st notch, Accessories position:
the ignition is off but the accessories can operate.
3. 2nd notch, On position:
the ignition is on.
4. Starting position:
the starter is operated.
Avoid pressing the buttons of your
remote control out of range of your
vehicle as this could stop it from
working. The remote control would
then have to be reprogrammed
(refer to the corresponding section).
Page 40 of 113
!
42
Keys
Make a careful note of the number of each key. This number is coded on the
label attached to the key.
Remote control
The high frequency remote control is a sensitive system; do not o perate it
while it is in your pocket as there is a possibilit y that it may unlock the vehicle,
without you being aware of it.
Do not repeatedly press the buttons of your remote control out of range and
out of sight of your vehicle. You run the risk of stopp ing it from working and the
remote control would have to be reprogrammed.
The remote control does not operate when the key is in the ignition, even when
t h e i g n i t i o n i s s w i t c h e d o f f , e x c e p t f o r r e p r o g r a m m i n g . Do not throw the remote control
batteries away, they contain metals
which are harmful to the environ-
ment.
Take them to an approved collection
point.
Locking the vehicle
Driving with the doors locked may make access to the passenger compart -
m e n t b y t h e e m e r g e n c y s e r v i c e s m o r e d i f fi c u l t i n a n e m e r g e n c y .
As a safety precaution (with children on board), remove the key fro m the
ignition when you leave the vehicle, even for a short time.
Anti-theft protection
D o n o t m a k e a n y m o d i fi c a t i o n s t o t h e e l e c t r o n i c e n g i n e i m m o b i l i s e r s y s t e m ,
this could cause malfunctions.
When purchasing a second-hand vehicle
Have the key codes memorised by a PEUGEOT dealer, to ensure that the
keys in your possession are the only ones which can start the vehicle .
Lost keys
V i s i t a P E U G E O T d e a l e r w i t h t h e v e h i c l e ' s V 5 r e g i s t r a t i o n c e r t i fi c a t e a n d
y o u r p e r s o n a l i d e n t i fi c a t i o n d o c u m e n t s .
The PEUGEOT network will be able to retrieve the key code and the trans-
ponder code to order a replacement key.
Page 41 of 113
i
40
KEYS
Central locking and unlocking
From the front doors, the keys allow you
to lock and unlock the doors and boot.
If one of the doors is open, the central
locking does not work.
If the boot is open, the central locking
works.
Remote control
This carries out the same functions as
the key, from a distance. Locking
Press button
A to lock the vehicle.
T h i s i s c o n fi r m e d b y fi x e d l i g h t i n g o f t h e
d i r e c t i o n i n d i c a t o r s f o r a p p r o x i m a t e l y
two seconds.
Unlocking
Press button B to unlock the vehicle.
T h i s i s c o n fi r m e d b y r a p i d fl a s h i n g o f
the direction indicators. Starting the vehicle
Steering lock
Before starting, unlock the steering, if
necessary, by turning the steering wheel
slightly while turning the key.
It is advisable to release the clutch dur-
ing the action of the starter to facilitate
the starting of the engine.
There are four possible positions of the
key in the ignition switch:
1. STOP position:
the ignition is off.
2. 1st notch, Accessories position:
the ignition is off but the accessories can operate.
3. 2nd notch, On position:
the ignition is on.
4. Starting position:
the starter is operated.
Avoid pressing the buttons of your
remote control out of range of your
vehicle as this could stop it from
working. The remote control would
then have to be reprogrammed
(refer to the corresponding section).
Page 43 of 113
!
42
Keys
Make a careful note of the number of each key. This number is coded on the
label attached to the key.
Remote control
The high frequency remote control is a sensitive system; do not o perate it
while it is in your pocket as there is a possibilit y that it may unlock the vehicle,
without you being aware of it.
Do not repeatedly press the buttons of your remote control out of range and
out of sight of your vehicle. You run the risk of stopp ing it from working and the
remote control would have to be reprogrammed.
The remote control does not operate when the key is in the ignition, even when
t h e i g n i t i o n i s s w i t c h e d o f f , e x c e p t f o r r e p r o g r a m m i n g . Do not throw the remote control
batteries away, they contain metals
which are harmful to the environ-
ment.
Take them to an approved collection
point.
Locking the vehicle
Driving with the doors locked may make access to the passenger compart -
m e n t b y t h e e m e r g e n c y s e r v i c e s m o r e d i f fi c u l t i n a n e m e r g e n c y .
As a safety precaution (with children on board), remove the key fro m the
ignition when you leave the vehicle, even for a short time.
Anti-theft protection
D o n o t m a k e a n y m o d i fi c a t i o n s t o t h e e l e c t r o n i c e n g i n e i m m o b i l i s e r s y s t e m ,
this could cause malfunctions.
When purchasing a second-hand vehicle
Have the key codes memorised by a PEUGEOT dealer, to ensure that the
keys in your possession are the only ones which can start the vehicle .
Lost keys
V i s i t a P E U G E O T d e a l e r w i t h t h e v e h i c l e ' s V 5 r e g i s t r a t i o n c e r t i fi c a t e a n d
y o u r p e r s o n a l i d e n t i fi c a t i o n d o c u m e n t s .
The PEUGEOT network will be able to retrieve the key code and the trans-
ponder code to order a replacement key.
Page 70 of 113
!
65
Programming
Turn dial 1 to the "CRUISE" po-
sition: the cruise control mode is
selected but is not switched on
(OFF).
Exceeding the programmed speed
Intentional or unintentional exceeding of the programmed
s p e e d r e s u l t s i n fl a s h i n g o f t h i s s p e e d o n t h e d i s p l a y .
Return to the programmed speed, by means of intentional or
unintentional deceleration of the vehicle, automatically ca n-
c e l s t h e fl a s h i n g o f t h e s p e e d .
Return to normal driving
Turn dial 1 to the "0" position: the cruise control mode is
deselected. The display returns to the distance rec order.
Set the programmed speed by ac-
celerating to the required speed,
then press button 2 or 3 (e.g.: 70 mph
(110 km/h)).
Switch off the cruise control by pressing button 4 : the
d i s p l a y c o n fi r m s t h a t i t h a s b e e n s w i t c h e d o f f ( O F F ) .
Switch the cruise control back on by pressing button 4
again.
You can then change the programmed speed using buttons
2 and 3 :
- by + or - 1 mph (km/h) = short press,
- by + or - 5 mph (km/h) = long press,
- in steps of + or - 5 mph (km/h) = maintained press. Operating fault
In the event of a cruise control malfunc-
tion, the speed is cleared resulting in
fl a s h i n g o f t h e d a s h e s .
Have it checked by a PEUGEOT dealer.
When the cruise control is switched
on, be careful if you maintain the
pressure on one of the programmed
speed changing buttons: this may
result in a very rapid change in the
speed of your vehicle.
Do not use the cruise control on
s l i p p e r y r o a d s o r i n h e a v y t r a f fi c .
On a steep descent, the cruise
control will not be able to prevent
the vehicle from exceeding the pro-
grammed speed.
To avoid any risk of jamming of the
pedals:
- ensure that the mat is posi-tioned correctly,
- n e v e r fi t o n e m a t o n t o p o f another.
Page 72 of 113
!
67
Programming
Turn dial 1 to the "LIMIT" position:
the speed limiter mode is selected
but is not switched on (OFF).
Exceeding the programmed speed
Pressing the accelerator pedal to exceed the programmed
speed will not have any effect unless you press the pedal
fi r m l y past the point of resistance .
The speed limiter is deactivated temporarily and the pro-
g r a m m e d s p e e d , w h i c h i s s t i l l d i s p l a y e d , fl a s h e s .
Returning to the programmed speed, by means of int entional
or unintentional deceleration of the vehicle, automaticall y
c a n c e l s t h e fl a s h i n g o f t h e p r o g r a m m e d s p e e d . Return to normal driving
Turn dial 1 to the "0" position: the
speed limiter mode is deselected.
The display returns to the distance
recorder.
You do not have to switch the speed
limiter on in order to set the speed.
Switch the speed limiter off by pressing button 4 : the dis-
p l a y c o n fi r m s t h a t i t h a s b e e n s w i t c h e d o f f ( O F F ) .
Switch the speed limiter back on by pressing button 4
again.
Set the speed value by pressing button 2 or 3 (e.g.:
55 mph (90 km/h)).
You can then change the programmed speed using buttons
2 and 3 :
- by + or - 1 mph (km/h) = short press,
- by + or - 5 mph (km/h) = long press,
- in steps of + or - 5 mph (km/h) = maintained press.
Switch the speed limiter on by pressing button 4 . Operating fault
In the event of a speed limiter malfunc-
tion, the speed is cleared resulting in
fl a s h i n g o f t h e d a s h e s .
Have the system checked by a PEUGEOT
dealer.
On a steep descent or in the event
of sharp acceleration, the speed
limiter will not be able to prevent
the vehicle from exceeding the pro-
grammed speed.
To avoid any risk of jamming of the
pedals:
- ensure that the mat is posi-tioned correctly,
- d o n o t fi t o n e m a t o n t o p o f a n - other.
Page 106 of 113
10
100
Button
Function
A Radio On/Off.
B - Decrease volume.
C + Increase volume.
D
CD eject.
E RDS * RDS function on/off.
P r e s s f o r m o r e t h a n 2 s e c o n d s : r e g i o n a l f o l l o w i n g m o d e o n / o f f .
F TA * T r a f fi c i n f o r m a t i o n p r i o r i t y o n / o f f .
P r e s s f o r m o r e t h a n 2 s e c o n d s : P T Y f u n c t i o n o n / o f f .
G
Setting of the bass, treble, loudness, sound distribution a
nd automatic volume correction.
H
Increase the setting of the functions associated with butto
n G .
I
Decrease the setting of the functions associated with butto
n G .
J
M a n u a l a n d a u t o m a t i c s e a r c h o f h i g h e r f r e q u e n c i e s .
S e l e c t i o n o f t h e n e x t t r a c k o n t h e C D a n d o f t h e P T Y ( r a d i o ) .
K MAN Manual/automatic operation of buttons J and L .
L
M a n u a l a n d a u t o m a t i c s e a r c h o f l o w e r f r e q u e n c i e s .
S e l e c t i o n o f t h e p r e v i o u s t r a c k o n t h e C D a n d o f t h e P T Y ( r a d i
o ) .
M CH. CD Selection of the CD changer source.
P r e s s f o r m o r e t h a n 2 s e c o n d s : r a n d o m p l a y .
N CD Selection of the CD source.
P r e s s f o r m o r e t h a n 2 s e c o n d s : r a n d o m p l a y .
O Radio S e l e c t i o n o f t h e r a d i o s o u r c e . S e l e c t i o n o f t h e F M 1 , F M 2 , F M A S T
, A M w a v e b a n d s .
P r e s s f o r m o r e t h a n 2 s e c o n d s : a u t o m a t i c s t o r i n g o f s t a t i o n s ( a u t o s t o r e ) .
1 to 6 1 2 3 4 5 6 Selection of the stored station.
P r e s s f o r m o r e t h a n 2 s e c o n d s : s t o r i n g o f a s t a t i o n .
* A c c o r d i n g t o c o u n t r y .
Page 107 of 113
10
101
GENERAL FUNCTIONS
On/off
W i t h t h e i g n i t i o n k e y i n
the accessories position
or with the ignition on,
press button A to switch
t h e a u d i o e q u i p m e n t o n
or off.
Anti-theft system
T h e a u d i o e q u i p m e n t i s c o d e d i n s u c h
a w a y t h a t i t c a n o n l y o p e r a t e i n y o u r
v e h i c l e . I t w o u l d n o t w o r k i f fi t t e d i n a n -
other vehicle.
The anti-theft system is automatic
and requires no action on your part.
P r e s s b u t t o n C to increase the audio
e q u i p m e n t v o l u m e o r b u t t o n B t o d e -
crease it.
A continuous press of buttons B and C
a d j u s t s t h e v o l u m e g r a d u a l l y .
AUDIO SETTINGS
P r e s s b u t t o n G several
times in succession to
access the bass (BASS) ,
treble (TREB) , loudness
(LOUD) , fader (FAD) ,
balance (BAL) a n d a u t o -
matic volume correction
settings.
Exit from audio mode is automatic after
a f e w s e c o n d s w i t h o u t a n y a c t i o n o r b y
pressing button G f o l l o w i n g c o n fi g u r a -
tion of the automatic volume correction. Adjusting the bass
When "BASS" i s d i s -
p l a y e d , p r e s s b u t t o n H or
I to change the setting.
- "BASS -9" f o r a m i n i -
mum bass setting,
- "BASS 0" f o r a s t a n d -
ard setting,
- "BASS +9" for a maximum bass
setting.
Adjusting the treble
When "TREB" i s d i s p l a y e d , p r e s s b u t -
ton H or I to change the setting.
- "TREB -9" for a minimum treble
setting,
- "TREB 0" for a standard setting,
- "TREB +9" for a maximum treble
setting.
Adjusting the loudness (LOUD)
T h i s f u n c t i o n a u t o m a t i c a l l y e m p h a s i s e s
bass and treble tones.
P r e s s b u t t o n H or I t o s w i t c h t h e f u n c -
tion on or off.
Note: b a s s , t r e b l e a n d l o u d n e s s s e t -
t i n g s a r e s p e c i fi c t o e a c h s o u r c e . T h e y
c a n b e s e t d i f f e r e n t l y f o r t h e r a d i o o r
CD.
The audio equipment can operate for
30 minutes without the ignition being
switched on.