2009 Peugeot 206 P Dag battery
[x] Cancel search: batteryPage 15 of 113
18
Engine autodiagnostics system.
The lighting of this warning light
indicates the occurrence of a
fault in the engine management
system.
Flashing of this warning light indicates
the occurrence of a fault in the emission
control system.
Engine oil pressure.
The lighting of this warning light
indicates the occurrence of a
fault in the engine lubrication
circuit. It is imperative that the vehicle is
stopped as soon as it is safe to do so. Battery charge.
The lighting of this warning light
indicates the occurrence of a
fault in the battery charging cir-
cuit (dirty or loose terminals, slack or
cut alternator belt, ...).
Braking.
The lighting of this warning light
indicates the occurrence of a fault
in one of the braking systems:
- s i g n i fi c a n t d r o p i n t h e l e v e l i n t h e circuit,
- electronic brake force distribution (EBFD) faulty (if lit at the same time
as the ABS warning light).
It is imperative that the vehicle is stopped as soon as it is safe to do so.
If the vehicle is moving, check that the
handbrake has been released fully.
Low fuel level.
The lighting of this warning light
indicates that there is enough
fuel left to drive approximately
30 miles (50 km).
The capacity of the fuel tank is approxi-
mately 50 litres. Maximum coolant
temperature.
The lighting of this warning light
indicates an excessively high
temperature in the cooling system. It is
imperative that the vehicle is stopped
as soon as it is safe to do so.
Door open.
A door, the boot or the bonnet
is still open:
Seat belt not fastened/
unfastened. The lighting of this warning light
indicates that the driver has not
fastened his seat belt or has
unfastened it.
- if the speed is below 6 mph (10 km/h),
this warning light comes on continu-
ously,
-
if the speed is above 6 mph (10 km/h),
this warning light comes on continuously,
accompanied by an audible signal.
Dynamic stability control
(ESP/ASR).
This warning light comes on for
a few seconds each time the
ignition is switched on.
When the engine is running and the
vehicle is moving, it comes on if the sys-
tem is activated.
It comes on continuously accompanied
by a message on the multifunction dis-
play when the system is deactivated.
If the warning light remains on when
the engine is running and the vehicle is
moving, contact a PEUGEOT dealer.
Page 19 of 113
ii
ii
21
Following this operation, if you wish
to disconnect the battery, lock the
v e h i c l e a n d w a i t a t l e a s t fi v e m i n u t e s
for the zero reset to be taken into
account.
Maintenance indicator zero reset
After each service, the maintenance
indicator must be reset to zero.
The procedure for resetting to zero is as
follows:
switch off the ignition,
press and hold the trip distance
recorder zero reset button,
switch on the ignition; the distance
recorder display begins a count-
down,
when the display indicates "=0" ,
release the button; the spanner dis-
appears.
The distance remaining may be
weighted by the time factor, depend-
ing on the driver's driving habits.
Therefore, the spanner may also
come on if you have exceeded the
two year service interval.
Service overdue
For 5 seconds after the ignition is
switched on,
t h e s p a n n e r fl a s h e s to
indicate that the service must be carried
out as soon as possible.
Example: the service is overdue by
300 miles/km.
For 5 seconds after the ignition is
switched on, the display indicates:
5 seconds after the ignition is switched
on, the distance recorder resumes
its normal operation. The spanner
remains lit .
Page 22 of 113
24
MONOCHROME DISPLAY B
This enables the following information
to be displayed:
- the time,
- the date,
- t h e o u t s i d e t e m p e r a t u r e * ( t h i s fl a s h -es when it is between -3 and 3 °C),
- the status of the doors. The display shows you, by means of a graphic,
whether a door is open,
- the warning messages (e.g. ''battery charge fault'') or information mes-
sages (e.g. "fuel level low''), dis-
played temporarily, can be cleared
by pressing button 1 or 2 ,
- the trip computer. Setting the parameters
Press button
1 for two seconds to ac-
c e s s t h e s e t t i n g s . T h e i n f o r m a t i o n fl a s h e s
t o s h o w i t i s r e a d y t o b e m o d i fi e d .
Then, individual presses on button 1
allow you to scroll through the various
data in the following sequence:
- language in which the information is displayed,
- unit of distance (kms or miles),
- unit of temperature (degrees Cel- sius or Fahrenheit),
- time format (12 then 24 hour mode),
- hour,
- minutes,
- year,
- month,
- day.
Pressing button 2 allows you to change
the information selected. Maintain the
pressure for rapid scrolling.
After 7 seconds without operation, the
screen returns to the normal display
a n d t h e m o d i fi e d d a t a i s r e c o r d e d .
* With automatic air conditioning only.
Page 42 of 113
i
4141
ELECTRONIC ENGINE
IMMOBILISER
This locks the engine control system as
soon as the ignition has been switched
off and therefore prevents starting of
the vehicle by anyone who does not
have the key.
The ignition key has an electronic chip
which has a special code. When the ig-
nition is switched on, the code must be
recognised for starting to be possible.
If the system does not function correct-
ly, the central locking button indicator light,
s i t u a t e d o n t h e h a n d b r a k e c o n s o l e , fl a s h -
es rapidly when the ignition is switched on
(2nd notch).
In this case your vehicle will not start.
Contact a PEUGEOT dealer as soon as
possible.
Key in ignition
If the key is left in the ignition, this
is indicated by an audible signal
when the driver's door is opened.
Locating your vehicle
To locate your vehicle, if you have
locked it, in a car park:
press button A , the courtesy lights
come on and the direction indicators
fl a s h f o r a f e w s e c o n d s .
Changing the remote control
battery
Battery ref.: CR2016/3 volts.
I f t h e r e m o t e c o n t r o l b a t t e r y i s fl a t , y o u
are warned by a message on display B.
To replace the battery, remove the
screw then unclip the casing using a
coin at the ring.
If the remote control does not work after
the battery has been changed, repro-
gramme the remote control. Programming the remote
control
Switch off the ignition.
Switch the ignition on again.
Press button A immediately for a
few seconds.
Switch off the ignition and remove
the remote control key from the igni-
tion lock. The remote control is now
working again.
Page 44 of 113
i
4141
ELECTRONIC ENGINE
IMMOBILISER
This locks the engine control system as
soon as the ignition has been switched
off and therefore prevents starting of
the vehicle by anyone who does not
have the key.
The ignition key has an electronic chip
which has a special code. When the ig-
nition is switched on, the code must be
recognised for starting to be possible.
If the system does not function correct-
ly, the central locking button indicator light,
s i t u a t e d o n t h e h a n d b r a k e c o n s o l e , fl a s h -
es rapidly when the ignition is switched on
(2nd notch).
In this case your vehicle will not start.
Contact a PEUGEOT dealer as soon as
possible.
Key in ignition
If the key is left in the ignition, this
is indicated by an audible signal
when the driver's door is opened.
Locating your vehicle
To locate your vehicle, if you have
locked it, in a car park:
press button A , the courtesy lights
come on and the direction indicators
fl a s h f o r a f e w s e c o n d s .
Changing the remote control
battery
Battery ref.: CR2016/3 volts.
I f t h e r e m o t e c o n t r o l b a t t e r y i s fl a t , y o u
are warned by a message on display B.
To replace the battery, remove the
screw then unclip the casing using a
coin at the ring.
If the remote control does not work after
the battery has been changed, repro-
gramme the remote control. Programming the remote
control
Switch off the ignition.
Switch the ignition on again.
Press button A immediately for a
few seconds.
Switch off the ignition and remove
the remote control key from the igni-
tion lock. The remote control is now
working again.
Page 74 of 113
69
1.4 LITRE TURBO DIESEL HDI
(70 BHP) ENGINE
1. Coolant reservoir.
2. Engine oil dipstick.
3. Power steering reservoir.
4. Windscreen wash reservoir.
5. Priming pump.
6. E n g i n e o i l fi l l e r c a p .
7. A i r fi l t e r .
8. B r a k e fl u i d r e s e r v o i r .
9. Battery.
10. Fuse box.
11. P a s s e n g e r c o m p a r t m e n t fi l t e r .
1.1 LITRE (60 BHP) AND 1.4 LITRE
(75 BHP) PETROL ENGINES
1. Power steering reservoir.
2. Windscreen wash reservoir.
3. Coolant reservoir.
4. B r a k e fl u i d r e s e r v o i r .
5. Battery (without protective cover for
the 1.1 litre engine).
6. A i r fi l t e r .
7. Dipstick.
8. E n g i n e o i l fi l l e r c a p .
9. P a s s e n g e r c o m p a r t m e n t fi l t e r .
Page 76 of 113
!
71
CHECKS
Check these components, or have them
c h e c k e d b y a P E U G E O T d e a l e r , i n a c -
cordance with the servicing booklet and
in relation to your engine.
Battery
Air filter and passenger
compartment filter Brake pads
Handbrake
Brake disc/drum wear Oil filter
Manual gearbox
O n l y u s e p r o d u c t s r e c o m m e n d e d b y
P E U G E O T o r p r o d u c t s o f e q u i v a -
l e n t q u a l i t y a n d s p e c i fi c a t i o n s .
At the start of winter, have
your battery checked by a
P E U G E O T d e a l e r .
H a v e t h e fi l t e r e l e m e n t s r e -
placed regularly.
If you drive
in dusty conditions, change
them twice as often. Brake pad wear depends on
the style of driving, in particu-
lar for vehicles which are used
in town, over short distances.
It may be necessary to check the thickness
of the pads, even between services.
Where the handbrake travel is
too great or there is a reduc-
tion in the performance of the
system, the handbrake should
be adjusted, even between
services.
Have the system checked by a
P E U G E O T d e a l e r .
For any information relating to
checking the wear of the brake
discs and/or drums, contact a
P E U G E O T d e a l e r . C h a n g e t h e fi l t e r r e g u l a r l y , i n
accordance with the servicing
schedule.
This does not require an oil
change. Check the level in ac-
cordance with the manufactur-
er's servicing schedule.
Page 89 of 113
83
or
Fuse N° Rating Functions
1 10 A Pre-heat unit (diesel) - Water in diesel sensor -
R e v e r s i n g l i g h t s w i t c h - S p e e d s e n s o r - A i r fl o w
sensor (diesel)
2 15 A Canister solenoid valve - Fuel pump
3 10 A ABS engine control unit
4 10 A Engine control unit
5 - Not used
6 15 A Front fog lamps
7 - Not used
8 20 A Fan assembly relay - Engine control unit - Diesel
injection pump - Diesel high pressure regulator -
Engine management solenoid valve
9 15 A Left-hand dipped beam
10 15 A Right-hand dipped beam 11 10 A Left-hand main beam
12 10 A Right-hand main beam
13 15 A Horn
14 10 A Front and rear windscreen wash pumps
15 30 A Throttle housing heater - Diesel injection pump -
O x y g e n s e n s o r - E n g i n e c o n t r o l u n i t - A i r fl o w
sensor - Ignition coil - Engine management
solenoid valve - Diesel heater - Injectors
16 30 A Air pump relay
17 30 A High and low speed windscreen wiper
18 40 A Air conditioning fan
Engine compartment fuse box
To gain access to the box in the engine
compartment (next to the battery), un-
clip the cover.
After carrying out work, close the cover
very carefully.