2009 OPEL CORSA lock

89
Instruments, controls
v
Airbag systems 3, belt tensioners 3
Control indicator lights up red.
Illuminates when the engine is runningFault in the airbag or belt tensioner system
3 61, 374.X
Seat belt 3
Control indicator lights up or flashes red.
Lamps

It lights up from when the ignition is
switched on until the dr iver’s seatbelt is
fastened.
Flashes
If the driver’s seatbelt has not been
fastened when the vehicle starts moving, a
warning light flashes.
Fasten seat belt 359, 362.
R

Brake system, clutch system
Control indicator lights up or flashes red.
Illuminated
Illuminates when the ignition is switched on
if the hand brake is applied 3167.
Lights up when the hand brake is released
when the fluid level for the brake or clutch
systems is low 3246.
FlashesFor vehicles with ma nual transmission
automated 3, the control indicator flashes
for a few seconds if the ignition is turned off
when the hand brake is not applied. u

Anti-lock brake system (ABS) 3
Control indicator lights up red.
Illuminates while driving
Fault in anti-lock braking system 3166.
v
Electronic Stability Programme
(ESP ®
Plus
)3
Control indicator flashes or lights up
yellow.
Flashing during driving
System engages actively 3151, 3159.
Illuminates while drivingSystem switched off or fault in system
3 159.m

Cruise control 3
Control indicator lights up or flashes green.
Lamps

Cruise control switched on 3160.
Flashes
Cruise control was enabled without
depressing the brake pedal beforehand
3 160.
9
Warning
Stop. Do not continue your journey. Con-
sult a workshop.
Back to overview

98 Instruments, controls
Picture no: 17331t.tif
Function areas
For each functional area there is a main
page (Main), which is selected at the top
edge of the display (not with the
Infotainment system CD 30 or the Mobile
Phone Portal):
zAudio,
z Navigation 3,
z Telephone 3,
z Trip computer 3.
For Audio, Navigation 3 and Telephone 3
functions – see infotainment system
instructions.
Picture no: 17332t.tif
System settings
Press the Main button 3 of the
infotainment system.
Press the Settings button of the
infotainment system . On Infotainment
System CD 30, make sure no menu has
been selected.
Picture no: 17340t.tif
Setting date and time 3
Select menu item Time, Date, from the
Settings menu.
Select the required menu item and make
setting.
FM AS [TP] REG CDin MP3

90.6
MHz
19,5° 19:36
7
Settings19,5° 19:36
Time, Date 19:36
Language
Units 07.05.2008
Contrast
Day / Night
! Ign. logic
7 Time, Date 19,5° 19:36
Time 19:36
Date 07.05.2008! Synchron. clock automatical.
Back to overview

99
Instruments, controls
Automatic time synchronisation 3
The RDS signal of most VHF transmitters
automatically sets the time.
Some transmitters do not send a correct
time signal. In such cases, we recommend
that you switch off automatic time
synchronisation.
On infotainment systems with navigation 3,
time and date are also harmonised upon
receipt of a GPS satellite signal.
The function is activated by ticking the field
in front of Synchron. clock automatical. in
the Time, Date menu.
Picture no: 17341t.tif
Language selection
You can select the display language for
some functions.
Select menu item Language from the
Settings menu.
Picture no: 17342t.tif
Select the desired language.
Selections are indicated by a 6 in front of
the menu item.
In systems with language version 3, when
the language setting of the display is
changed, the system will ask if the message
language should also be changed - see
infotainment system instructions.
7
Settings 19,5° 19:36
Time, Date
Language Deutsch
Units English
Contrast Español
Day / Night ....
! Ign. logic
7
13 Languages 19,5° 19:36!
Deutsch
English
Español
Nederlands
Français
Italiano
Back to overview

113
Lighting
Picture no: 18302s.tif
Lead-me lighting
3
The dipped beam remains switched on for
approx. 30 seconds once you have left the
vehicle and closed the driver’s door.
To activate
1. Switch off ignition.
2. Remove ignition key.
3. Open driver’s door.
4. Pull turn signal stalk toward steering wheel.
5. Close driver’s door.
If the driver’s door is left open, the lamps
will go out after two minutes.
The light is switched off immediately by
inserting the key into the ignition or pulling
the turn signal stalk towards the steering
wheel again.
Picture no: 18420s.tif
Switching on the exterior lighting
with the remote control
3
The lead-me-to-the-car light function
switches the dipped beam on for
approx. 30 seconds.
Program function
This function can be activated and
deactivated depending on the key used,
see "Personalised key", P1 339 341. To activate
Press button
q on the remote control twice
when the vehicle is locked.
Country-specific application 3: To switch
on the Lead-me-to-the-car light function,
press button q on the remote control once
the vehicle is locked.
Switching on the ignition or pressing
button p on the remote control will
deactivate the Lead-me-to-the-car light
function early.
Back to overview

114 Lighting
Picture no: 18370s.tif
Parking lamps The front parking lamp and tail lamp of
one side of the vehicle can be activated
when parking:
1. Set light switch to 7 or A 3,
2. Ignition off,
3. Move turn signal stalk all the way up (right parking lamp) or down (left
parking lamp).
Confirmed by a signal and the
corresponding turn signal control indicator.
To switch it off, swit ch on the ignition or
move the turn signal stalk in the opposite
direction.
Picture no: 18201s.tif
Instrument illumination
,
Information display illumination

Lights come on when ignition is switched
on.
Adjustable brightness when exterior
lighting is switched on:
Hold down the button until the required
brightness is achieved.
Display mode 33100.
Courtesy lamp Automatic interior light
Comes on automatically when the vehicle is
unlocked with the remote control, when a
door is opened or when the key is removed
from the ignition switch after the ignition is
switched off.
Goes off automatically after a delay when
the doors are closed or immediately when
the ignition is switched on or the doors are
locked.
Brighter = Push button +
Darker = Push button -
Back to overview

116 Lighting
Picture no: 17133t.tif
Courtesy lamps and rear reading lamps 3
Operated with switch (I = on, 0 = off,
centre = automatic interior light). Welcome Light
3
After unlocking the car, the instrument and
switch lighting, the front and rear foot well
lighting 3 and the information display 3
come on for a few seconds.
Glove compartment lighting 3
Glove compartment lighting comes on
when the lid is opened.
Luggage compartment lighting
The luggage compartment light comes on
when the tailgate is open.
Automatically regulated centre console
lighting 3
Spotlight in housing of interior mirror.
Daylight-dependent, automatically
regulated centre console lighting with
ignition switched on.
Battery discharge protection To prevent the battery from becoming
discharged, the courtesy lamp, reading
lamps 3, luggage compartment lighting
and glove compartment lighting 3 switch
off automatically 5 minutes after the
ignition is switched off. Misted light covers The inside of the light covers may mist up
briefly in poor, wet and cold weather
conditions, in heavy rain or after washing.
The mist disappears quickly by itself; to
help, switch on the lights.
Back to overview

123
Climate control
Picture no: 18208s.tif
Heating and ventilation system Temperature
Adjusted using left-hand rotary switch.
The amount of heat is dependent on the
coolant temperature and is thus not fully
attained until the engine is warm.
Picture no: 18209s.tif
Air flow
Adjusted using centre rotary switch.
The rate of air flow is determined by the
fan. The fan should therefore also be
switched on during a journey.
Picture no: 18207s.tif
Air distribution
Set using right rotary switch.
Intermediate settings are possible.
Open the air vents when the switch is set to
L or M.
Turn clockwise = Warm
Turn anticlockwise = Cold
x
Off
1 - 4 Selected fan speed
MTo headroom via adjustable
air vents
L To headroom via adjustable
air vents, to footwell
K To footwell
J To windscreen, to front side
windows, to footwell
l To windscreen and front side
windows
Back to overview

124 Climate control
Picture no: 18210s.tif
Ventilation
zSet the temperature to the desired
setting.
z Switch fan on, select fan setting
according to requirements.
z For maximum ventilation in the head
area: set the air distribution switch to M,
open all air vents, direct the air vent slats
3 122.
z For ventilation to foot well: Set air
distribution switch to K.
z For simultaneous ventilation to the head
area and the foot well: Set air
distribution switch to L. Heating
For rapid warming of the passenger
compartment:
z
Turn the temperature switch clockwise as
far as it will go (warm).
z Set the fan to speed 3.
z Open air vents.
z Set air distribution switch to desired
position, preferably position J, 3 123. The comfort and general well-being of the
vehicle occupants are to a large extent
dependent on a suitab
le ventilation and
heating setting.
To achieve temperature layering with the
pleasant effect of "cool head and warm
feet", set the air distribution rotary switch
to K or J and move the rotary
temperature switch to any position you like
(with temperature strati fication effect in
the centre zone).
Back to overview