2009 OPEL ANTARA Instrument table

In brief20
Parking the vehicle:
Apply hand brake firmly,
close windows,
switch off engine, remove key,
engage steering column lock,
lock vehicle
6Further information - see pages 22, 128,
radio frequency remote control -
see page 23,
central locking system - see page 25,
anti-theft alarm system - see page 27.
Advice when parking:
z Always apply hand brake firmly and as
firmly as possible on slopes.
z Push key into igniti on switch before
removing (vehicles with automatic
transmission 3: depress foot brake and
shift into P before removing key). Turn
steering wheel until lock is felt to engage
(anti-theft protection).
z If the vehicle is parked on a level surface
or a hill, select 1st gear before switching
ignition off (vehicles with automatic
transmission 3: move selector lever to P ).
Also turn front wheels away from kerb if
parked on an uphill slope.
If the vehicle is parked on a downhill
slope, select reverse gear before
switching ignition off (vehicles with
automatic transmission 3: move selector
lever to P). Also turn front wheels
towards kerb.
z Switch off exterior lamps, otherwise the
headlamp warning device will sound
when the driver’s door is opened.
z Cooling fans may run on after the engine
has been switched off.
z Do not park on easily ignitable surfaces
as hot exhaust system temperatures
could cause the surface to ignite.
That was the most important
information for your first drive in
your Antara in brief.
Your vehicle has still more
instruments and controls,
possibly also optional equipment.

The remaining chapters of the
Owner’s Manual contain
important information on
operation, safety and
maintenance as well as a
complete index.

Instruments, controls91
The desired stop watch display can be
selected from the Optionsmenu3:
Driving Time excl. Stops
The time the vehicle is in motion is
recorded. Stationary ti me is not included.
Driving Time incl. Stops
The time the vehicle is in motion is
recorded. The time the vehicle is stationary
with the key in the ignition switch is
included.
Travel Time
Measurement of the time from manual
activation via Start to manual deactivation
via Reset .
Display of current tyre pressure 3
Select menu item Tyres from the Board
Computer menu.
The current pressure of each tyre is
displayed.
Further information – see page 144.
Check control 3
In vehicles with tyre pressure monitoring
system 3, if tyre pressure is too low, the
display indicates which tyre to check, e.g.:
Tyre pressure
check rear
right tyre
(value in bar)
Check tyre pressure at next opportunity
using suitable gauge.
Tyre pressure monitoring system 3 –
see page 144.
Tyre pressure – see page 224.
In vehicles with tyre pressure monitoring
system 3, if there is a major loss of pressure
in a tyre, the display indicates the tyre at
fault, e.g.:
Attention!
Rear left tyre
pressure loss
(value in bar)
Stop immediately and check tyre.
Tyre pressure monitoring system 3 –
see page 144.
Tyre pressure – see page 224.
Ü Board Computer
BC 1
BC 2
Timer
Tyres

Instruments, controls92
Warning buzzers
While driving:
z when operating th e turn signals.
z if driver’s or passenger’s seat belt 3 is
not engaged when the seat is occupied
and vehicle speed exceeds approx.
22 km/h (14 mph).
When the vehicle is parked and driver’s
door is opened:
z with exterior lamps switched on.
z when the key is in the ignition switch.
6 Seat belt warning chimes -
see pages 46, 72,
driving hints - see page 127,
save fuel, protect the environment -
see page 129.
Windscreen wipers
To activate, move lever upwards.
Press lever down from position J:
single swipe.
Further information - see pages 198, 202,
205. Adjustable wiper interval
To set the wiping interval to a value
between 1 and 10 seconds:
Switch on ignition.
Push lever down from position
J.
Wait the desired interval.
Set the lever to adjustable timed interval
wiper position $.
The interval remains stored until the next
change or the ignition is switched off.
Switching the ignition on and moving the
lever to $ sets the interval to 3.5 seconds.
In this mode, wiping frequency is also
affected by vehicle speed. As vehicle speed
increases, wiping will become more
frequent.
J
=Off
$ =Timed interval wipe
% =Slow
& =Fast

Climate control110
Cooling
Operational only with engine running and
with the fan switched on:
Control indicator in the button illuminates
when air conditioning is enabled and
extinguishes when the system is switched
off.
Cooling switches off automatically at low
outside temperatures.
Engine power and performance may be
affected when the system is on.
If the fan is switched off, the air
conditioning system will not operate. Once activated, the air conditioning
system is operated via the normal heating
and ventilation controls.
Even with air conditioning on, if
temperature rotary knob is set to warm, the
vehicle will still produce warm air in the
passenger compartment.
To improve efficiency of the air
conditioning, always close the windows,
to prevent chilled air from escaping.
Switching on the air conditioning will assist
in windscreen demisting. In very hot
temperatures, before starting the engine,
allow hot air to escape from the vehicle by
opening the windows and sun roof
3.
When the air conditioning system is
switched on, at least one of the adjustable
centre or side air vents must be open, so
that the evaporator does not ice up due to
lack of air movement.
Driving in stop-and-go traffic may reduce
the effectiveness of the air conditioning
system.
Using the air conditioning system when
driving up long hills or in heavy traffic
can cause engine overheating. If engine
coolant temperature warning control
indicator W illuminates in instrument
panel, turn off air co nditioning and allow
engine to idle for a few minutes (see
page 71). Normal cooling
z
Press button n
(to switch on air co nditioning system).
z Turn air recirculation mode 4 off.
z Set air distribution rotary knob to
position M or L.
z Turn temperature rotary knob to blue
area for cooling.
z Set fan to desired speed.
z Open air vents as required.
Press button
n=On
Press button n again = Off

Driving and operation120
Fault Z
If a fault occurs in the automatic
transmission, control indicator Z will
illuminate in the instrument panel.
Automatic shifting may be much harsher
than normal or, in the case of a serious
fault, cancelled altogether.
Consult a workshop as soon as possible to
have the cause of the fault eliminated. Interruption of power supply
The clutch is not disengaged if the vehicle
battery is discharged and a gear has been
selected. The vehicle cannot move.
If the battery is flat, the selector lever
cannot be moved out of position
P or N.
Start the vehicle using jump leads -
see page 172. If the cause of the interruption to the power
supply is not a discharged battery, release
selector lever:
Have cause of power supply interruption
remedied immediately. Consult a
workshop.
1. Turn off ignition and remove key.
2. Depress and hold foot brake.
3. Remove cap on console with a suitable
screwdriver.
4. Insert ignition key and press gently into shift lock release slot.
5. Shift to neutral (N).
6. Remove key from shift lock release slot.
7. Start engine and shift to chosen gear.
8. Reinstall cap on console.

Driving and operation138
Hydraulic Brake Assist (HBA)
When the ESC function comes into action
and recognises any emergency situations
requiring hard braking, it automatically
delivers increased braking pressure to the
wheels.
Active Rollover Protection (ARP)
If the vehicle moves in an unstable manner,
this function helps the vehicle maintain
normal stability.
Trailer Stability Assist (TSA) 3
TSA monitors vehicle movements when
towing a caravan or trailer. If the system
detects lurching movements, engine power
is reduced and the vehicle/trailer
combination is selectiv ely braked until the
lurching ceases. DCS (Descent Control System)
The Descent Control System allows the
vehicle to travel at a low speed without
depressing the foot brake.
The vehicle will automatically decelerate to
a low speed and remain at that speed
when DCS button
5 is pressed.
Use only when descending steep grades
while driving off-road. Do not use when
driving on normal road surfaces.
Some noise or vibration from the brake
system may be apparent when DCS is
active. To activate
At speeds below approx. 50 km/h
(30 mph), press DCS button. The green DCS
control indicator
5 will flash in the
instrument panel, to show DCS is in
operation.
DCS will not activate at speeds above
50 km/h (30 mph), even if the button is
pressed.
Unnecessary usage of the DCS function,
such as while driving on normal roads, may
damage the brake system and the ESC
function.

Self-help, vehicle care194
Engine oil change, oil filter change
Engine oil changes are to be carried out
depending on time intervals or kilometre/
mileage intervals, since oil loses its
lubrication properties not only through
engine operation but also through ageing.
We recommend that you use genuine Opel
oil filters.

Remember to reset the engine oil life
monitor 3 whenever the engine oil is
changed.
Engine oil life monitor 3
The engine oil life monitor lets you know
when to change the oil. Based on driving
conditions, the kilometre/mileage interval
at which an oil change will be indicated can
vary considerably.
For the system to work properly, it must be
reset every time the oil is changed. Consult
a workshop.
When the system has calculated that oil life
has been diminished, control indicator C
illuminates in the instrument panel -
see page 73. Engine oil needs changing
within approx. 1000 km (600 miles). Engine
power may be decreased.Diesel fuel filter
Drain diesel fuel filter of residual water at
every engine oil change.
Place a container underneath the filter
housing. Turn drain plug, located on the
left of the filter housing, anti-clockwise
using a suitable screwdriver, to drain off
the water.
The filter is drained as soon as diesel fuel
emerges from the port. Retighten the drain
plug by turning it clockwise.
With engine switched off, turn ignition key
to ON, wait approx. 5 seconds, and turn
key to LOCK to perform priming operation.
Perform this operation 3 times or more
while the engine is switched off, to avoid air
entering the fuel line.
9 Warning
Used engine oil filters and empty oil
containers should not be disposed of as
domestic refuse. We recommend that
you entrust oil and oil filter changes to a
workshop who is familiar with legal
requirements regarding disposal of used
oil and can thus help to protect both the
environment and your health.
Engine oil is a danger to health; avoid
prolonged contact with skin and wash
exposed areas thoroughly.

Self-help, vehicle care204
Plastic and rubber parts
For additional cleaning of plastic and
rubber parts, use a cleaner suitable for
vehicle interiors. Do not use any other
agent, and in particular do not use solvents
or petrol.
Wheels and tyres
Do not use high-pressure jet cleaners on
wheels and tyres.
Interior and upholstery
Clean the vehicle interior regularly,
including the instrument panel fascia,
using Interior/Upholstery Cleaner.
Clean fabric upholstery with a vacuum
cleaner and brush. To remove stains, use a
cleaner that is suitable for both fabrics and
vinyl.
Open Velcro fastener s on clothing could
damage seat upholstery. Make sure that
Velcro fasteners are closed.
Do not use cleaning agents such as
acetone, carbon te trachloride, paint
thinner, paint remover, nail varnish
remover, washing powder or bleach to
clean fabrics, carpets, the instrument panel
or leather trim 3 in the vehicle interior.
Benzine, petrol, naphth a, enamel reducers
and lacquer thinners are also unsuitable. Avoid over-exposure to vapours from
cleaning agents and
other chemicals when
cleaning. Whenever possible, avoid using
such cleaning agents in small, unventilated
spaces, to avoid inhalation of dangerous
vapours. Open the doors.
If the front seats are equipped with side
airbags 3, do not use chemical solvents or
strong detergents on the seat covers.
Do not saturate the seat covers with
Interior/Upholstery Cleaner, to avoid
contaminating the airbag system,
otherwise the side airbags 3 may not
trigger in the event of a collision. Seat belts
Always keep seat be
lts clean and dry.
Clean seat belts only with lukewarm water
or Interior/Upholstery Cleaner.
Periodically check the seat belts and
replace immediately with new seat belts if
damage or weakening of the belts has
occurred.
Windows
When cleaning the heated rear window,
make sure that the heating element on the
inside of the window is not damaged.
Never place stickers on the inside of the
rear window.
Use a soft, lint-fr ee cloth or chamois
leather, in conjunction with Window
Cleaning Spray and Insect Remover. Do not
use sharp instruments or abrasive cleaners.
Opel Cleaning Solvent and Antifreeze is
suitable for de-icing windows.
For mechanical removal of ice, use a
commercially available sharp-edged ice
scraper. Press the scraper firmly against
the glass so that no dirt can get under it
and scratch the glass.