2009 OPEL ANTARA instrument panel

Lighting98
Peripheral lighting
The dipped beam and reversing lamps
illuminate for approx. 30 seconds after the
driver exits the vehicle and closes the door.
To activate function:
If the driver’s door is left open, the lamps
will extinguish after two minutes.
Peripheral lighting can be deactivated by
inserting the key in the ignition switch or by
pulling the turn signal lever towards the
steering wheel again while the driver’s door
is open.
Instrument illumination,
information display illumination
Comes on when ignition is switched on.
Brightness can be adjusted when the
exterior lamps are on: turn wheel to the
right or left until the desired brightness is
obtained.
If driver’s door is opened or q is pressed on
the remote control, instrument panel lamps
will illuminate automatically and stay on
for approx. 30 seconds until ignition switch
is turned to the ACC position.
Display mode 3 - see page 87.
Interior courtesy lamps
Front reading lamps, rear interior lamps
and luggage compartm ent lamps function
as courtesy lighting and illuminate when
the doors or tailgate are opened.
If doors or tailgate remain opened, the
lamps stay illuminated for approx.
10 minutes.
Once all doors and the tailgate are closed,
the courtesy lamps dim gradually after
approx. 10 seconds.
By pressing button d, both front reading
lamps and the rear interior lamps
illuminate.
Press the button again to turn the lamps
off.
1. Switch off ignition.
2. Remove ignition key.
3. Open driver’s door.
4. Pull turn signal lever towards
steering wheel.

Climate control110
Cooling
Operational only with engine running and
with the fan switched on:
Control indicator in the button illuminates
when air conditioning is enabled and
extinguishes when the system is switched
off.
Cooling switches off automatically at low
outside temperatures.
Engine power and performance may be
affected when the system is on.
If the fan is switched off, the air
conditioning system will not operate. Once activated, the air conditioning
system is operated via the normal heating
and ventilation controls.
Even with air conditioning on, if
temperature rotary knob is set to warm, the
vehicle will still produce warm air in the
passenger compartment.
To improve efficiency of the air
conditioning, always close the windows,
to prevent chilled air from escaping.
Switching on the air conditioning will assist
in windscreen demisting. In very hot
temperatures, before starting the engine,
allow hot air to escape from the vehicle by
opening the windows and sun roof
3.
When the air conditioning system is
switched on, at least one of the adjustable
centre or side air vents must be open, so
that the evaporator does not ice up due to
lack of air movement.
Driving in stop-and-go traffic may reduce
the effectiveness of the air conditioning
system.
Using the air conditioning system when
driving up long hills or in heavy traffic
can cause engine overheating. If engine
coolant temperature warning control
indicator W illuminates in instrument
panel, turn off air co nditioning and allow
engine to idle for a few minutes (see
page 71). Normal cooling
z
Press button n
(to switch on air co nditioning system).
z Turn air recirculation mode 4 off.
z Set air distribution rotary knob to
position M or L.
z Turn temperature rotary knob to blue
area for cooling.
z Set fan to desired speed.
z Open air vents as required.
Press button
n=On
Press button n again = Off

Driving and operation117
Manual mode
Move selector lever out of position D (to the
left) into manual gate, then forwards or
backwards.
Tip selector lever in the appropriate
direction. It then returns to centre position.
Gearshifting in manual mode can be
achieved whilst accelerating.
If the engine speed is too low, the
transmission will automatically shift to a
lower gear, even in manual mode. This
prevents the engine from stalling.
After stopping, 1st gear is automatically
selected.
No automatic shifting to a higher gear
takes place at high engine speeds. When upshifting in manual mode, take
heed of prevailing road conditions,
keeping engine speed below the red zone.
Downshifts must be made in accordance
with vehicle speed.
Gears can be skipped by moving the
selector lever repeated
ly at short intervals.
When starting on slippery surfaces, move
selector lever forwards to engage 2nd
gear.
The selected gear is displayed in the
transmission display.
For safety reasons, kickdown is also
available in manual mode - see page 118.
To move back to D, push selector lever
back to the right. Winter program
In the event of difficult
ies starting-off on icy
and slippery surfac es, press button n;
control indicator
0 is illuminated in the
instrument panel and the vehicle sets off in
3rd gear, to reduce slipping and loss of
traction.
Winter program is switched off by:
z pressing button n again
(control indicator
0 will extinguish in
instrument panel),
z turning off the ignition.
If the vehicle is switched to manual mode
while Winter program is active, the Winter
program is switched off.
]Shift to a lower gear.

Driving and operation120
Fault Z
If a fault occurs in the automatic
transmission, control indicator Z will
illuminate in the instrument panel.
Automatic shifting may be much harsher
than normal or, in the case of a serious
fault, cancelled altogether.
Consult a workshop as soon as possible to
have the cause of the fault eliminated. Interruption of power supply
The clutch is not disengaged if the vehicle
battery is discharged and a gear has been
selected. The vehicle cannot move.
If the battery is flat, the selector lever
cannot be moved out of position
P or N.
Start the vehicle using jump leads -
see page 172. If the cause of the interruption to the power
supply is not a discharged battery, release
selector lever:
Have cause of power supply interruption
remedied immediately. Consult a
workshop.
1. Turn off ignition and remove key.
2. Depress and hold foot brake.
3. Remove cap on console with a suitable
screwdriver.
4. Insert ignition key and press gently into shift lock release slot.
5. Shift to neutral (N).
6. Remove key from shift lock release slot.
7. Start engine and shift to chosen gear.
8. Reinstall cap on console.

Driving and operation136
Drive control systems
Electronic Stability Control (ESC)
The Electronic Stability Control improves
driving stability when necessary,
independently of the type of road surface
and the tyre grip. It also prevents the drive
wheels from spinning.
The system monitors vehicle movements.
As soon as the vehicle starts to swerve
(understeers/oversteers), engine output is
reduced (the sound of the engine changes)
and individual wheels are specifically
braked. This considerably improves the
driving stability of the vehicle on snow and
ice and on wet or slippery road surfaces.
ESC is ready for operation after the ignition
is switched on and the ESC control
indicators
7, A and J illuminate then
extinguish after approx. 4 seconds. When the ESC comes into action, control
indicator
7 flashes in the instrument panel.
Some noise or vibration may be apparent.
The vehicle is now in a critical situation;
the ESC helps you to keep control of the
vehicle and reminds you to match your
speed to the road conditions.
ESC A
ctive & Warning control indicator 7The control indicator illuminates in yellow
for approx. 4 seconds when the ignition is
switched on. The system is ready for
operation when it extinguishes.
Flashing when driving;
The system has come into action. The
engine output may be reduced (the sound
of the engine changes) and the vehicle
may be braked automatically to a small
degree.
Illuminated when driving;
Fault in the system. Poor road surface
conditions may cause vehicle stability to be
impaired.
Have the cause of the fault remedied by a
workshop. The system’s integrated self-
diagnostics allows faults to be quickly
remedied.
9 Warning
Do not let this special safety feature
tempt you into taking risks when driving.
Traffic safety can only be achieved by
adopting a responsible driving style.

Driving and operation137
ESC Not Ready control indicator AThe control indicator illuminates in yellow
for approx. 4 seconds when the ignition is
switched on.
Illuminates to indicate that the system is
not ready for conditions to operate.
May illuminate in cold conditions. It should
extinguish when the vehicle warms up. Switching offControl indicator
J illuminates in yellow for
approx. 4 seconds when the ignition is
switched on.
With ESC active, if wheels are slipping on
wet, snowy or icy roads, engine speed may
not increase when accelerator pedal is
depressed. The vehicle may not move. Turn off ESC function to allow engine rpm
to increase, by pressing button
J. Control
indicator J illuminates in the instrument
panel.
The ESC function is turned on again by
pressing button J again (control indicator
extinguishes) or the next time the ignition is
switched on.

Driving and operation138
Hydraulic Brake Assist (HBA)
When the ESC function comes into action
and recognises any emergency situations
requiring hard braking, it automatically
delivers increased braking pressure to the
wheels.
Active Rollover Protection (ARP)
If the vehicle moves in an unstable manner,
this function helps the vehicle maintain
normal stability.
Trailer Stability Assist (TSA) 3
TSA monitors vehicle movements when
towing a caravan or trailer. If the system
detects lurching movements, engine power
is reduced and the vehicle/trailer
combination is selectiv ely braked until the
lurching ceases. DCS (Descent Control System)
The Descent Control System allows the
vehicle to travel at a low speed without
depressing the foot brake.
The vehicle will automatically decelerate to
a low speed and remain at that speed
when DCS button
5 is pressed.
Use only when descending steep grades
while driving off-road. Do not use when
driving on normal road surfaces.
Some noise or vibration from the brake
system may be apparent when DCS is
active. To activate
At speeds below approx. 50 km/h
(30 mph), press DCS button. The green DCS
control indicator
5 will flash in the
instrument panel, to show DCS is in
operation.
DCS will not activate at speeds above
50 km/h (30 mph), even if the button is
pressed.
Unnecessary usage of the DCS function,
such as while driving on normal roads, may
damage the brake system and the ESC
function.

Driving and operation142
Park pilot 3
The park pilot makes parking easier by
measuring the distance between the
vehicle and any obstacles to the front and
rear and giving an acoustic signal in the
passenger compartment.
The system records the distance using four
sensors in both the front and rear bumpers.
To activate
The park pilot activates automatically
when the ignition is switched on and a
forward gear or reverse gear is engaged
and the hand brake is released. The acoustic signal may differ depending
on the type of object detected.
If the vehicle approaches an obstacle when
in a forward gear or while reversing, a
series of signals can be heard in the vehicle
interior. The interval between the signals
becomes shorter as the distance is
reduced. If the distance is less than 30 cm,
the signal will be continuous.
To deactivate
The system deactivates automatically
when in neutral (aut omatic transmission 3
in N or P) with the hand brake applied.
When the vehicle speed is greater than
8 km/h (5 mph), the system also
deactivates.
To deactivate the system manually, press
button
b on the instrument panel.
The control indicator in the button will
illuminate.
If the button is pressed again, the control
indicator in the button will extinguish and
the system will be reactivated as soon as a
forward gear or reverse gear is engaged
and the hand brake is released.
9 Warning
Under certain circumstances, various
reflective surfaces on objects or clothing
as well as external noise sources may
cause the system to fail to detect
obstacles.
The park pilot may not recognise sharp
objects, thick clothes or sponge-like
materials which absorb the frequency.
If the sensors are damaged or covered
with snow, dirt or ice, the park pilot may
not activate.
For these reasons, care must be taken
when reversing, even if the park pilot is
operational. This is of particular
importance when in the vicinity of
pedestrians.