2009 OPEL AGILA tyre pressure

0-1 Introduction
Introduction
Vehicle specific data
Please enter your vehicle’s data here to keep it easily accessible. This information is available under the chapters
“Service and maintenance” and "Technical data" as well as on the identification plate.
FuelDesignation
Engine oil
Grade
Viscosity
Tyre pressureTyre size with up to 3 persons with full load
Summer tyres Front Rear Front Rear
Winter tyres Front Rear Front Rear
WeightsPermissible Gross
Vehicle Weight
– EC kerb
weight
= Payload

9-2Driving and operating
To release the steering column lock,
turn ignition key to position ACC and
rotate steering wheel slightly.
Before starting-off, check:
„Tyre pressures and condition.
„Engine oil level and fluid levels in
engine compartment 3 10-3.
„All windows, mirrors, exterior
lighting and license plates are free
from dirt, snow and ice and are
operational.
„Objects are securely located and
will not be thrown forward in the
event of sudden braking.
„Seats, seat belts and mirrors are
correctly adjusted.
„All gauges and control indicators.
„Brake operation.
Starting the engine
With manual transmission in neutral,
depress clutch and foot brake,
(automatic transmission 3 in P or N),
do not accelerate.
Petrol engines: Turn key to START
and release it.
Diesel engines: Turn key to ON,
when preheating control indicator N
extinguishes, turn key to START and
release it.
Preheating system switches on only if
outside temperature is low.
Key returns automatically to ON
position when released.Start attempts should not last longer
than 15 seconds. If engine does not
start, wait 15 seconds before
repeating starting procedure. If
necessary, depress accelerator
before repeating starting procedure.
Parking the vehicle
„Apply the parking brake firmly
without actuating the release
button. On a downhill or uphill
slope, apply as firmly as possible.
Depress foot brake at the same
time to reduce operating forces.
„Push key into ignition switch before
turning to LOCK position and
removing (vehicles with automatic
transmission3: depress foot brake
and shift into P). Turn steering
wheel until lock is felt to engage
(anti-theft protection).
„If the vehicle is parked on a level
surface or a hill, select 1st gear
before switching the ignition off,
(vehicles with automatic
transmission 3: shift into P). Also
turn front wheels away from kerb if
parked on an uphill slope.

9-10Driving and operating
Brake assist
Rapid powerful application of the
brake pedal automatically applies
maximum brake force amplification to
achieve the shortest possible braking
distance under full braking (brake
assist).
Maintain steady pressure on the
brake pedal for as long as full-on
braking is to continue. When the
brake pedal is released, the
maximum brake force amplification is
taken away.
Ride control systems
Electronic Stability Program
(ESP®) 3
The Electronic Stability Program
improves driving stability when
necessary, independently of the type
of road surface and the tyre grip. It
also prevents the drive wheels from
spinning.
The system monitors vehicle
movements. As soon as the vehicle
starts to swerve (understeers/
oversteers), engine output is reduced
(the sound of the engine changes)
and individual wheels are specifically
braked. This considerably improves
the driving stability of the vehicle on
snow and ice and on wet or slippery
road surfaces.
ESP
® is ready for operation as soon
as the ignition is switched on and the
control indicators
R, ESP and TCSS OFF extinguish.
When the ESP® comes into action,
control indicator
R flashes rapidly in
the instrument cluster. Some noise or
vibration may be apparent.ESP active control indicator 3 5-10.
Interruption of power supply
If the vehicle’s battery has been
disconnected and reconnected,
ESP
® is deactivated and control
indicator R flashes once per second.
Reactivate ESP® by driving in a
straight line at over 15 km/h (9 mph)
for a few seconds until flashing
ceases. Several seconds may lapse
before the control indicator
extinguishes, depending on road
conditions.
Caution
Do not let this special safety feature
tempt you into taking risks when
driving.
Traffic safety can only be achieved
by adopting a responsible driving
style.

10-15Vehicle care
Some circuits may be protected by
several fuses.
Wheels
Tyres
Factory-fitted tyres are matched to
the chassis and offer optimum driving
comfort and safety.
Winter tyres 3
Tyres of size 165/70 R 14 and
185/60 R 15 may be used as winter
tyres.
Winter tyres improve safety at
temperatures below 7
°C and should
therefore be fitted on all the wheels.
Depending on national regulations, a
notice indicating the maximum
permissible speed for the tyres must
be affixed within the driver's field of
vision.
The maximum permissible speed
varies from country to country on
account of national regulations.
Ensure that winter tyres are inflated
to the correct pressure specified by
the tyre manufacturer. No. Circuit
1Starter motor
2Air conditioning compressor
3Fuel pump
4Fuel injection
5Heater fan
6Radiator fan
7Power steering control
module
8ABS, ESP
9ABS, ESP
10Brake lamp switch
11Headlamp (right)
12Headlamp (left)
13Front fog lamps
14Ignition switch
15Ignition switch, power
windows, wipers, starter No. Circuit

10-16 Vehicle care
Tyre designations
Meanings:
e.g. 185/60 R 15 84 T
Speed code letters:
Tyre pressure
Tyre pressures 3 12-8.
Also may be shown on a label located
on the driver’s door pillar.After having checked the tyre
pressures, securely tighten the valve
caps.
The specified tyre pressures are valid
for cold tyres. The increased tyre
pressure resulting from extensive
driving must not be reduced. The tyre
pressures specified apply to both
summer and winter tyres.
Incorrect tyre pressures will impair
safety, vehicle handling, comfort and
fuel economy and will increase tyre
wear. 185= Tyre width in mm
60= Aspect ratio
(tyre height to tyre width
in %)
R= Belt type: Radial
15= Rim diameter in inches
84= Load index
e.g.: 84 represents 500 kg
T= Speed code
Q= Up to 160 km/h (100 mph)
S= Up to 180 km/h (112 mph)
T= Up to 190 km/h (118 mph)
H= Up to 210 km/h (130 mph)
V= Up to 240 km/h (150 mph)
W= Up to 270 km/h (168 mph)

10-17Vehicle care
Tyre condition
Drive over edges slowly and at a right
angle if possible. When parking,
ensure that the tyres are not pressed
against the edge of the kerb.
Check tyres regularly for damage
(foreign bodies, punctures, cuts,
cracks, bulges in sidewalls). Check
wheels for damage. In the event of
damage or abnormal wear, seek the
assistance of a workshop.
Different tyre and wheel
types
If tyres of a different size to those
fitted at the factory are used (this
includes winter tyres), the electronic speedometer may possibly need to
be reprogrammed, to ensure that the
speed displayed is correct.
Wheel covers 3
Wheel covers and tyres that are
approved for the vehicle and comply
with all of the relevant wheel and tyre
combination requirements must be
used.
If the wheel covers and tyres used
are not approved, make sure that the
tyres do not have a beaded edge.
Remove wheel covers before fitting
tyre chains, to avoid damaging the
wheel covers.
Tyre chains 3
Tyre chains are only permitted on the
drive wheels (front axle). They must
be fitted to the tyres symmetrically in
order to achieve a concentric fit.
Use fine mesh chains that add no
more than 10 mm to the tyre tread
and the inboard sides (including
chain lock).
Tyre chains may only be used at
speeds of up to 50 km/h (30 mph) or
up to the tyre chain manufacturer’s
recommended maximum speed,
whichever is lower.
9 Warning
If the pressure is too low, this can
result in considerable tyre warm-
up and internal damage, leading
to tread separation and even to
tyre blow-out at high speeds.
Caution
Use of unsuitable tyres or wheels
may lead to accidents and render
the vehicle unroadworthy.

10-19Vehicle care
2. Unscrew valve cap from
defective tyre and unscrew
valve insert using supplied
remover.
9 Warning
The air remaining in the tyre can
cause the insert to be forced out
under pressure during removal.
3. Remove the plug from the end
of the filler hose and insert filler
hose onto tyre valve.
4. Hold the sealant bottle with
bottom pointing upwards and
squeeze all of the sealant into
the tyre.
5. Disconnect filler hose and firmly
screw insert into valve using the
valve insert remover.
If necessary, use the supplied
spare valve insert.6. Place the compressor unit on
level ground and unwrap the air
compressor hose from the
compressor unit.
Ensure the compressor on/off
switch is in position O (off) and
screw the hose on to tyre valve.

10-20 Vehicle care
7. Unwrap accessory plug lead
from the compressor unit.
Insert plug into accessory
socket.
8. Turn ignition key to
position ACC.9. Switch compressor on/off
switch to position I(on).
10. Inflate the tyre to the correct
pressure 3 12-8.
If there is no reading, the air
compressor hose to tyre valve
connection may be faulty.
Re-check the connection.
If the required tyre pressure is
not obtained within 10 minutes,
rotate the tyre to evenly spread
the sealant and repeat the
procedure.
If the required tyre pressure is
still not obtained, the tyre is too
badly damaged. Seek the
assistance of a workshop.
If the tyre is overinflated,
reduce the pressure by
pressing the deflation button
on the compressor.
Do not operate the compressor
for more than 10 minutes, to
avoid overheating.
11. When the correct tyre pressure
has been reached, switch
compressor on/off switch to
position O(off).
12. Remove accessory plug from
the accessory socket, detach
air compressor hose from tyre
valve and replace valve cap.
13. Return air compressor hose
and accessory plug lead to
their original locations in the
compressor unit.