2009 OPEL AGILA fuel

10-14 Vehicle care
Do not store any objects behind the
cover.
Some circuits may be protected by
several fuses.Diesel engines
The fusebox is located behind the
rear of the battery.
To open, disengage cover and lift
upwards.
No. Circuit
1Heater fan
2Fuel injection
3Air conditioning compressor
4Automatic transmission
5Brake lamp switch
6ABS, ESP
7Starter motor
8-
9Power steering control
module
10Ignition switch
11Radiator fan
12-
13ABS, ESP
14-
15Engine electrics
16Front fog lamps
17Headlamp (left)
18Headlamp (right) No. Circuit

10-15Vehicle care
Some circuits may be protected by
several fuses.
Wheels
Tyres
Factory-fitted tyres are matched to
the chassis and offer optimum driving
comfort and safety.
Winter tyres 3
Tyres of size 165/70 R 14 and
185/60 R 15 may be used as winter
tyres.
Winter tyres improve safety at
temperatures below 7
°C and should
therefore be fitted on all the wheels.
Depending on national regulations, a
notice indicating the maximum
permissible speed for the tyres must
be affixed within the driver's field of
vision.
The maximum permissible speed
varies from country to country on
account of national regulations.
Ensure that winter tyres are inflated
to the correct pressure specified by
the tyre manufacturer. No. Circuit
1Starter motor
2Air conditioning compressor
3Fuel pump
4Fuel injection
5Heater fan
6Radiator fan
7Power steering control
module
8ABS, ESP
9ABS, ESP
10Brake lamp switch
11Headlamp (right)
12Headlamp (left)
13Front fog lamps
14Ignition switch
15Ignition switch, power
windows, wipers, starter No. Circuit

10-16 Vehicle care
Tyre designations
Meanings:
e.g. 185/60 R 15 84 T
Speed code letters:
Tyre pressure
Tyre pressures 3 12-8.
Also may be shown on a label located
on the driver’s door pillar.After having checked the tyre
pressures, securely tighten the valve
caps.
The specified tyre pressures are valid
for cold tyres. The increased tyre
pressure resulting from extensive
driving must not be reduced. The tyre
pressures specified apply to both
summer and winter tyres.
Incorrect tyre pressures will impair
safety, vehicle handling, comfort and
fuel economy and will increase tyre
wear. 185= Tyre width in mm
60= Aspect ratio
(tyre height to tyre width
in %)
R= Belt type: Radial
15= Rim diameter in inches
84= Load index
e.g.: 84 represents 500 kg
T= Speed code
Q= Up to 160 km/h (100 mph)
S= Up to 180 km/h (112 mph)
T= Up to 190 km/h (118 mph)
H= Up to 210 km/h (130 mph)
V= Up to 240 km/h (150 mph)
W= Up to 270 km/h (168 mph)

11-3 Service and maintenance
Service operations by year 1)
km ( x 1000)1)
miles ( x 1000)1)
1)Whichever occurs first.⊕Additional operations.o Under extreme operating conditions and if required by country-specific conditions, the intervals are reduced.
1
15
102
30
203
45
304
60
405
75
506
90
60
Ribbed V-belt: visual check - petrol engines only x x
⊕ Replace every 6 years/90,000 km/60,000 miles
Ribbed V-belt and tensioner: visual check - diesel engines only x x x
⊕ Replace every 10 years/150,000 km/100,000 miles
⊕Valve clearances: check, adjust - petrol engines only x x x
Engine oil and oil filter: replace x x x x x x
oDiesel fuel filter: drain water x x x x x x
Diesel fuel filter: replace and bleed x x x
⊕Manual transmission: oil level check, correct x
Oil changexx
Parking brake cable: check, adjust x
Parking brake: check and adjust
Wheel mounting and suspension front and rear, brake lines, brake
pressure hoses, fuel lines, fuel tank and exhaust system: visual checkxxx
Corrosion protection: check and record in Service and Warranty Booklet annually
Front and rear wheel brakes: check visually x x x x x x

11-5Service and maintenance
Additional servicing
Additional operations ⊕
Additional work is work that is not
required every service but can be
performed in conjunction with a
regular service.
Time allowances for such work are
not included in the scope of regular
services and will be charged for
additionally. It is more economic if
these operations are performed as
part of a scheduled service than
having them performed separately.
Severe operating conditions o
Operating conditions are classified as
severe when one or more of the
following occurs frequently:
„cold starts,
„stop and go,
„trailer/caravan towing,
„gradients and/or high altitudes,
„poor road surfaces,
„sand and dust,
„extreme temperature fluctuations. Police vehicles, taxis and driving
school vehicles are also classified as
operating under severe conditions.
Under severe operating conditions, it
may be necessary to have certain
scheduled service work done more
frequently than the scheduled
intervals.
For example, if fuel is used that does
not comply with required standards,
the fuel filter may need more frequent
draining or replacement and it may
also be necessary to change other
components more often (e.g. spark
plugs).
It is recommended to seek technical
advice on the servicing requirements
dependent on the specific operating
conditions of your vehicle.
Recommended fluids
and lubricants
Only use products that have been
tested and approved. Damage
resulting from the use of non-
approved materials will not be
covered by the warranty.
Checking and topping up fluids
3 10-3.
9 Warning
Operating materials are
hazardous and must be handled
with the appropriate level of care.
If consumed, seek medical
attention immediately. Do not
inhale fumes and avoid skin
contact. Keep out of reach of
children. Do not allow operating
materials to contaminate the
sewage system, surface water,
ground water or soil. Dispose of
empty containers properly.
Always bear in mind that
operating materials are
hazardous to your health.

12-1 Technical data
Technical dataVehicle identification
Vehicle Identification
Number (VIN)
The technical data is determined in
accordance with European
Community standards. We reserve
the right to make modifications.
Specifications in the vehicle
documents always have priority over
those given in this manual.
The Vehicle Identification Number
(VIN) is on the vehicle identification
plate, located on the driver’s door
pillar, visible with the door open.
Vehicle identification plate
Information on identification plate:
1Manufacturer
2Vehicle Identification Number
3Permissible Gross Vehicle Weight
4Permissible Gross Train Weight
5Maximum permissible front axle
load
6Maximum permissible rear axle
load
7Type approval number
8Engine designation
The combined total of front and rear
axle loads must not exceed the
permissible Gross Vehicle Weight. Vehicle identification............. 12-1
Engine data .......................... 12-3
Performance ......................... 12-4
Fuel consumption,
CO2 emission..................... 12-4
Capacities............................. 12-5
Dimensions........................... 12-6
Vehicle weights .................... 12-7
Tyre pressures in kPa/bar .... 12-8

12-4 Technical data
Performance
(approx. km/h/mph)
Fuel consumption, CO2emission
(approx.)Engine K 10 B K 12 B D 13 A
Maximum speed
1)
Manual transmission
Automatic transmission
1)The maximum speed indicated is achievable at kerb weight (without driver) plus 200 kg payload. Optional equipment could reduce the
specified maximum speed of the vehicle.
160/99
-175/109
170/106165/103
-
Engine K 10 B K 12 B D 13 A
Manual transmission/Automatic transmission
Urban (l/100km)
Extra-urban (l/100km)
Total (l/100km)
CO
2 (g/km)5.9/ -
4.4/ -
5.0/ -
120/-6.9/ 7.8
4.7/ 4.9
5.5/ 5.9
131/1425.5/ -
4.0/ -
4.5/ -
120/-

12-5 Technical data
Capacities
(approx. in litres)
Engine K 10 B K 12 B D 13 A
Engine coolant 4.4 4.5 5.9
Fuel tank 45 45 45
Engine oil with filter change 3.9 3.9 3.2
Engine oil between MIN and MAX
on dipstick1.0 1.0 1.0
Washer fluid reservoir for windscreen
and rear window washer system2.5 2.5 2.5