2009 NISSAN GT-R reset

Black plate (23,1)
Model "R35-D" EDITED: 2008/ 5/ 20
1. Trip A/B reset switch (P.2-5)
2. Speedometer (P.2-5)
3. Tachometer (P.2-6)/Upshift indicator (P.2-8)
4. Transmission position indicator (P.2-7)
5. Engine coolant temperature gauge (P.2-6)
6. ENTER switch (P.2-13)7. Instrument brightness control switch (P.2-10)
8. Vehicle information display (P.2-10)
9. Odometer/twin trip odometer (P.2-5)
10. Fuel gauge (P.2-7)
11. NEXT switch (P.2-13)
NOTE:.
Meters and gauges will illuminate
when the ignition switch is pushed to
the ON position.
. The needle indicators may move
slightly after the ignition switch is
pushed to the OFF position. This does
not indicate that there is a malfunction.
Illustrated table of contents
0-9
METERS AND GAUGES
,QIRUPDWLRQ3URYLGHGE\

Black plate (28,1)
Model "R35-D" EDITED: 2008/ 5/ 20
WARNING
.Do not ride in a moving vehicle
when the seatback is reclined. This
can be dangerous. The shoulder belt
will not be against your body. In an
accident, you could be thrown into it
and receive neck or other serious
injuries. You could also slide under
the lap belt and receive serious
internal injuries.
. For the most effective protection
when the vehicle is in motion, the
seat should be upright. Always sit well back in the seat with both feet
on the floor and adjust the seat
properly. (
“PRECAUTIONS ON
SEAT BELT USAGE” page 1-5)
. After adjustment, gently rock in the
seat to make sure it is securely
locked.
. Do not leave children unattended
inside the vehicle. They could un-
knowingly activate switches or con-
trols. Unattended children could
become involved in serious acci-
dents.
FRONT SEATS
Front power seat adjustmentOperating tips
.The power seat motor has an auto-reset
overload protection circuit. If the motor
stops during operation, wait 30 seconds,
then reactivate the switch.
. Do not operate the power seat switch for a
long period of time when the engine is off.
This will discharge the battery.
1-2
Safety — Seats, seat belts and supplemental restraint system
SEATS
,QIRUPDWLRQ3URYLGHGE\

Black plate (76,1)
Model "R35-D" EDITED: 2008/ 5/ 20
1. Trip A/B reset switch (P.2-5)
2. Speedometer (P.2-5)
3. Tachometer (P.2-6)/Upshift indicator (P.2-8)
4. Transmission position indicator (P.2-7)
5. Engine coolant temperature gauge (P.2-6)
6. ENTER switch (P.2-13)7. Instrument brightness control switch (P.2-10)
8. Vehicle information display (P.2-10)
9. Odometer/twin trip odometer (P.2-5)
10. Fuel gauge (P.2-7)
11. NEXT switch (P.2-13)
NOTE:.
Meters and gauges will illuminate
when the ignition switch is pushed to
the ON position.
. The needle indicators may move
slightly after the ignition switch is
pushed to the OFF position. This does
not indicate that there is a malfunction.
2-4
Instruments and controls
METERS AND GAUGES
,QIRUPDWLRQ3URYLGHGE\

Black plate (77,1)
Model "R35-D" EDITED: 2008/ 5/ 20
SPEEDOMETERThe speedometer indicates the vehicle speed.
ODOMETER/TWIN TRIP ODOME-
TERThe odometer
*1
indicates the total distance
that the vehicle has been driven.
Thetwintripodometer
*2
indicates the
distance of individual trips.
Changing the displayPress the TRIP A/B RESET switch to change
between trips
&Aand
&B.
Resetting the trip odometerTo reset a trip, display the trip that you want to
reset to zero, then press and hold the TRIP A/B
RESET switch for more than 1 second.
NOTE:When the battery is disconnected, the
memory for trips
&A
and
&B
is erased,
and both return to zero.
Instruments and controls
2-5
,QIRUPDWLRQ3URYLGHGE\

Black plate (87,1)
Model "R35-D" EDITED: 2008/ 5/ 20
AVERAGE FUEL CONSUMPTION
AND SPEEDThis displays the average fuel economy and
average vehicle speed beginning from the time
when the display was last reset.
To reset the display, press and hold the NEXT
switch
for more than 1 second. (The
average fuel economy and average vehicle
speed are reset at the same time.)
NOTE:. “
” is displayed during the first 1/3
mile (500 m) or the first 30 seconds
after a reset. .
The values are updated approximately
every 30 seconds.
ELAPSED TIME AND TRIP ODOME-
TERThis displays the elapsed time and trip odometer
beginning from the time when the display was
last reset.
To reset the display, press and hold the NEXT
switch
for more than 1 second. (The
elapsed time and trip odometer are reset at
the same time.)Instruments and controls
2-15
,QIRUPDWLRQ3URYLGHGE\

Black plate (91,1)
Model "R35-D" EDITED: 2008/ 5/ 20
MaintenanceThis function can be used to set the various
maintenance intervals and to check the engine
oil level. The reminders shown below are used to
notify the driver of the maintenance intervals.NOTE:Because these are displayed based on the
mileage driven, they do not indicate the
actual conditions of the vehicle. Use these
functions only as a reference.
Input the maintenance distance using the
following items:
.On each setting screen, push the NEXT
switch
to change the mileage. Push and hold the switch to increase the number
every 600 miles (1,000 km) .
. Set to “—” to set no reminders.
. To reset the accumulated mileage to zero,
go to the RESET screen, then push the
NEXT switch
and confirm with the
ENTER switch.
NOTE:. To restore the mileage to the original
figure after resetting, press the NEXT
switch
again.
. When the battery terminal is discon-
nected, the set mileage will be erased
and the settings will return to their
default settings.
Engine oil level:This can be used to check the pre-start oil level
while the engine is running. Select SETTING >
MAINTENANCE > OIL > ENGINE OIL >
LEVEL.
If the low level reminder appears, check the level
using the engine oil dipstick. (
“CHECKING
ENGINE OIL LEVEL” page 8-12)
Instruments and controls
2-19
,QIRUPDWLRQ3URYLGHGE\

Black plate (92,1)
Model "R35-D" EDITED: 2008/ 5/ 20
Engine oil:When the set mileage approaches, the reminder
will appear on the display and the remaining
distance is displayed at regular intervals. Select
SETTING > MAINTENANCE > OIL > ENGINE
OIL to set or reset the mileage for the engine oil
change.NOTE:The default setting is 6,000 miles (10,000
km) . The maximum mileage that can be set
is 6,000 miles (10,000 km) .
Engine oil filter:The reminder is displayed when the set mileage
is exceeded. Select SETTING > MAINTE-
NANCE > FILTER to set or reset the mileage
for the engine oil filter change.NOTE:The default setting is OFF. The maximum
mileage that can be set is 6,000 miles
(10,000 km) .
Transmission oil:The reminder is displayed when the set mileage
is exceeded. Select SETTING > MAINTE-
NANCE > OIL > T/M OIL to set or reset the
mileage for the transmission oil change.NOTE:The default setting is 18,500 miles (30,000
km) . The maximum mileage that can be set
is 18,500 miles (30,000 km) .
2-20
Instruments and controls
,QIRUPDWLRQ3URYLGHGE\

Black plate (93,1)
Model "R35-D" EDITED: 2008/ 5/ 20
Tires:The reminder is displayed when the set mileage
is exceeded. Select SETTING > MAINTE-
NANCE > TIRE to set or reset the mileage for
the tire change.NOTE:The default setting is OFF.
OptionsThis function can be used to make settings for
language and unit.Language:Select ENGLISH or FRANCAIS for use in the
vehicle information display.Unit:Select METRIC or US for use in the vehicle
information display.
WARNING (drive computer)Warning information is displayed on the vehicle
information display.
Press the ENTER switch
while a warning
display is active to return to the original display.
It is also possible to check any warnings that
have not been corrected. (
“WARNING
DISPLAY” page 2-31)
Checking the warningsUse the NEXT switch
to select “DETAILS”,
then confirm with the ENTER switch
.
When there are multiple warnings, press the
ENTER switch
to change the display
Instruments and controls
2-21
,QIRUPDWLRQ3URYLGHGE\