2009 Lancia Musa ESP

123
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
STARTING
AND
DRIVING
SNOW CHAINS
Use of snow chains should be in com-
pliance with local regulations.
The snow chains may be applied only
onto the front wheel tyres (drive
wheels). Use of Lineaccessori Lancia
snow chains is recommended.
Check the tension of the chains after
the first few metres have been driven.
IMPORTANT The spare wheel cannot
be fitted with snow chains. If the front
tyre has a puncture, replace a rear
wheel with the spare wheel and move
the rear wheel to the front axle. This
way, having two standard size wheels
on the front axle, is it possible to fit
the chains.
The tyres that can be fitted with snow chains and the respective chain
type for each version are shown in the above table; always comply
with the above specifications.
Keep your speed down when snow chains are fitted. Do not
exceed 50 km/h. Avoid potholes, steps and pavements and
avoid also to drive for long distances on roads not covered
with snow to prevent damaging the car and the roadbed.
Tyres that can be fitted withType of snow snow chainschains to be used
185/65 R14 86T
195/60 R15 88T
205/50 R16 87V tyres can-
not be fitted with snow
chains.
WARNING
Standard size snow chains
with max. projection over the
tyre track of 12 mm.
113-124 MUSA 1ed GB 10-07-2008 9:37 Pagina 123

124
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
STARTING
AND
DRIVING
EXTENDED
CAR INACTIVITY
If the car is to be left inactive for
longer than a month, the following
precautions should be noted:
❒park the car in covered, dry and
if possible well-ventilated premises;
❒engage a gear;
❒check that the handbrake is not
engaged;
❒disconnect the negative battery
terminal and check battery charge.
Repeat this check once every three
months during storage. Recharge
if the optical indicator shows a
dark colour without the central
green area;❒clean ad protect the painted parts
using protection waxes;
❒clean and protect the shiny metal
parts using special compounds
readily available;
❒sprinkle talcum powder on the
rubber windscreen and rear win-
dow wiper blades and lift them off
the glass;
❒slightly open the windows;
❒cover the car with a fabric or per-
forated plastic sheet. Do not use
compact plastic sheets that pre-
vent moisture on the car surface
from evaporating;❒inflate the tyres at a pressure of
+0.5 bar with respect to the nor-
mally specified pressure and check
it regularly;
❒if you don’t disconnect the battery
from the electric system, check its
charge every month and recharge
it if the optical indicator shows a
dark colour without the central
green area;
❒do not drain the engine cooling
system.
113-124 MUSA 1ed GB 10-07-2008 9:37 Pagina 124

146
WARNING
LIGHTS AND
MESSAGES
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
STARTING
AND
DRIVING
IN AN
EMERGENCY
fig. 14L0D0165mfig. 15L0D0166m
❒fit the spare wheel, ensuring that
the holes coincide M-fig. 14with
their respective centring pins N;
❒using the wrench provided, tighten
the four fastening bolts;
❒turn the jack handle to lower the
car and remove the jack;
❒using the wrench provided, screw
the bolts right down in a criss-
cross fashion, in the sequence
shown in the figureREFITTING THE
STANDARD WHEEL
Following the procedure described
previously, raise the car and remove
the small spare wheel.
Versions with steel rims
Proceed as follows:
❒make sure the contact surfaces be-
tween spare wheel and hub are
clean and free from impurities so
that the fastening bolts will not
come loose;
❒fit the standard wheel by inserting
the first two-threaded bolt in the
hole nearest to the inflation valve;❒fit the wheel cap, ensuring that the
groove (in the cap itself) coincides
with the inflation valve. Then fit
the other three bolts;
❒for versions with snap-fitted wheel
cap, press down on the edge of the
cap, with the palm of your hand
(do not strike it) against the wheel;
❒Using the wrench provided, se-
curely tighten the fastening bolts;
❒lower the car and remove the jack;
❒Using the wrench provided, fully
tighten the bolts in the sequence
shown in fig. 15;
IMPORTANT If it is not fitted prop-
erly, the wheel cap may detach itself
when the vehicle is running.
135-164 MUSA 1ed GB 10-07-2008 9:38 Pagina 146

147
WARNING
LIGHTS AND
MESSAGES
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
STARTING
AND
DRIVING
IN AN
EMERGENCY
Versions with alloy rims
❒Ensure that the surfaces in contact
with the hub are clean;
❒install the standard wheel by fit-
ting it on the centring pins. Fit the
fastening bolts and screw them
down using the wrench provided;
❒lower the car and remove the jack;
❒using the wrench provided, fully
tighten the bolts in the sequence
shown in fig. 15for the small
spare wheel;
❒refit the snap-fitted hub cap.When you have finished
❒stow the spare wheel in the space
provided in the boot;
❒ fit the jack partially open in its
box, forcing it lightly to prevent it
from vibrating when travelling;
❒put the tools back into their places
in the container;
❒stow the container, complete with
tools, into the spare wheel, screw-
ing in the locking device;
❒put the boot’s stiff preformed in-
sulating mat back in position.WHEN NEEDING
TO CHANGE
A BULB
GENERAL INSTRUCTIONS
❒When a bulb is not working, check
that the corresponding fuse is in-
tact before replacing it: refer to the
“If a fuse blows” paragraph in this
chapter for fuse location;
❒Before changing a bulb check the
contacts for oxidation;
❒burnt bulbs must be replaced by
others of the same type and power;
❒For safety reasons, always check
the height of the headlight beam
after changing a bulb.
Halogen lamps must be han-
dled holding the metallic
part only. Touching the
transparent part of the bulb
with your fingers may reduce the in-
tensity of the emitted light and even
compromise duration of the lamp it-
self. In the event of accidental contact,
rub the bulb with a cloth dampened
with alcohol and allow to dry.
135-164 MUSA 1ed GB 10-07-2008 9:38 Pagina 147

148
WARNING
LIGHTS AND
MESSAGES
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
STARTING
AND
DRIVING
IN AN
EMERGENCY
Changes or repairs to the
electrical system (electric
control units) carried out incorrectly
and without due consideration for
the technical specifications of the
system can lead to malfunctioning
and generate a fire hazard.
WARNING
Halogen lamps contain gas
under pressure. Their
breaking can cause scattering of
glass fragments.
WARNING
BULB TYPES fig. 16
Various types of bulbs are fitted to
your car:
A All glass bulb: clipped into place.
Pull to extract.
B Bayonet bulbs: to remove this type
of bulb from its holder, press the
bulb and turn it anticlockwise.
C Cylindrical bulbs: release from the
contacts to extract.
D-E Halogen bulbs: release the fas
tening clip from the correspond
ing seat to remove the lamp.
L0D0178mfig. 16
The rear sidelights and
brake lights and the third
brake light are LEDs so in the event
of malfunctioning, contact a Lancia
Dealership.
WARNING
IMPORTANT A slight misting may ap-
pear on the internal surface of the
headlight: this does not indicate a fault
and is caused by low temperature and
the degree of humidity in the air. Mist-
ing will rapidly disappear when the
headlights are switched on. The pres-
ence of drops inside the headlights in-
dicates infiltration of water. Contact a
Lancia Dealership
135-164 MUSA 1ed GB 10-07-2008 9:38 Pagina 148

159
WARNING
LIGHTS AND
MESSAGES
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
STARTING
AND
DRIVING
IN AN
EMERGENCY
FUSE TABLE
Dashboard fuse box
ELECTRICAL DEVICESFUSE AMPERE
Right dipped beam F12 7,5
Left dipped beam / beam aim controlF13 7,5
Engine compartment fuse box relay coil / body computer F31 7.5
AvailableF32 –
Rear left window winderF33 20
Rear right window winderF34 20
+15 Cruise control, signal from switch on brake pedal to control units, reversing light (*) F35 7.5
+30 Set-up for trailer control unit, rear locks front locks with single control unit for the doors (*) F36 10
+15 Third brake light, instrument panel, brake lights (*) F37 7.5
Central locking, fuel flap actuatorF38 20
+30 EOBD diagnosis socket, sound system, navigator, tyre pressure control unit (*)F39 10
Heated rear window F40 30
Heated electric mirrors F41 7.5
+15 ABS / ESP control unit (*)F42 7.5
Wiper/ windscreen washer / rear window washer F43 30
Cigar lighter / console current outletF44 15
Heated seats F45 15
Boot current outletF46 15
Driver side door control unit powering (electric windows) F47 20
Passenger side door control unit powering (electric windows) F48 20
+15 Functions (lighting of controls on left and central panels, electric windows, lighting of heated seat
controls,set-up for mobile phone, navigator, rain / dusk sensors, parking sensors control unit,
lighting of controls for sun roof) (*)F49 7.5
Airbag control unit F50 7.5
+15 Tyre pressure control unitF51 7.5
Wiper/ rear window washer, cigar lighter F52 15
+30 Direction indicators, emergency lights, instrument panel (*) F5 7.5
(*) +30 = battery direct positive terminal (not key-operated)
+15 = positive terminal key operated
135-164 MUSA 1ed GB 10-07-2008 9:38 Pagina 159

163
WARNING
LIGHTS AND
MESSAGES
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
STARTING
AND
DRIVING
IN AN
EMERGENCY
TOWING THE CAR
There are two two hooks provided:
the shorter one is used for the front
and the longer one for the rear.
The tow hooks are kept in the tool
box.
Fig. 41 andfig. 42 alongside, show
the positioning of the rear ring (long)
with respect to the inside of the small
spare wheel and in the Fix & Go au-
tomatic quick tyre repair kit.
If the Dual FuNction System gearbox
is installed in the car, ensure that the
gearbox is in neutral N(by checking
that the car moves when pushed) and
proceed as per the towing of a normal
car with mechanical gearbox.
If it is not possible to put the gearbox
in neutral, do not tow the vehicle and
contact a Lancia Dealership.
fig. 41L0D0342m
fig. 42L0D0369m
DISASSEMBLY OF TOW HOOK
CAPS
In order to avoid damage to the cap
A-fig. 43, perform th
efollowing steps
to disassemble:
❒take the screwdriver provided
from the tool box;
❒insert the screwdriver in the slot B
on the cap;
❒place your thumb on the cap to
safeguard against damage (see fig-
ure);
❒extract the cap (without turning
it) by pulling at an angle that is
perpendicular to the supporting
surfacefig. 44.
fig. 43L0D0250m
135-164 MUSA 1ed GB 10-07-2008 9:38 Pagina 163

164
WARNING
LIGHTS AND
MESSAGES
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
STARTING
AND
DRIVING
IN AN
EMERGENCY
fig. 44L0D0251m
HOOKING THE TOW RING
Proceed as follows:
❒take the tow hook B-fig. 45from
its support;
❒tighten the ring on the rear or
front threaded pin.
fig. 45L0D0487m
fig. 46L0D0205m
The power brakes and the
electrical power steering
will not work while the car is being
towed. More effort on the brake
pedal and steering wheel will there-
fore be required. Do not use wires
for towing. Do not jerk. Make sure
not to damage parts in contact with
the car while towing. When towing
the vehicle, be sure to respect the
specific rules of the Highway Code
when towing the car specifically in
relation to the towing device and the
behaviour to maintain on the road.
WARNING
Before beginning the tow,
turn the ignition key to
MAR and then to STOP, without ex-
tracting it When the key is removed,
the steering wheel lock automati-
cally activates. making it impossible
to turn the wheels.
WARNING
During towing do not start
up the engine.
WARNING
135-164 MUSA 1ed GB 10-07-2008 9:38 Pagina 164