2009 LAMBORGHINI GALLARDO gear box
[x] Cancel search: gear boxPage 1342 of 1659
8
L714 09 72 03
)G
) L J
) L J ) L J
H
I
M
L
1
® Automobili Lamborghini S.p.A. 7 K H L Q I R U P D W L R Q D Q G S U R F H G X U H V S X E O L V K H G E H O R Z D U H V W U L F W O \ F R Q ¿ G H Q W L D O D Q G H [ F O X V L Y H O \ I R U W K H / D P E R U J K L Q L ' H D O H U 1 H W Z R U N D Q G $ X W K R U L ] H G 6 H U Y L F H 3 R L Q W V $ O O F R S \ U L J K W V D U H S U R S H U W \ R I $ X W R P R E L O L
/ D P E R U J K L Q L 6 S $ E D V H G R Q F R S \ U L J K W O D Z $ O O R I W K H 3 ' ) F K D S W H U V L Q W K H : ( % Z R U N V K R S P D Q X D O V G H V F U L E H G E H O R Z D U H E D V H G R Q L Q I R U P D W L R Q D Y D L O D E O H D W W K H W L P H R I S X E O L F D W L R Q 7 K H F R P S D Q \ U H V H U Y H V
W K H U L J K W W R P D N H X S G D W H V D Q G P R G L ¿ F D W L R Q V 7 K H I R O O R Z L Q J D U H S U R K L E L W H G U H S U L Q W L Q J U H S U R G X F W L R Q I R U Z D U G L Q J W R X Q D X W K R U L ] H G S H R S O H D Q G R U W K L U G S D U W L H V D Q G W U D Q V O D W L R Q L Q F O X G L Q J S D U W L D O Z L W K R X W
Z U L W W H Q D X W K R U L ] D W L R Q I U R P $ X W R P R E L O L / D P E R U J K L Q L 6 S $
5. Unscrew the nut ( ) ) L J ) securing the positive rear battery cable to the alternator ( * ) L J ).
6 . Disconnect the 3 clamps ( + ) L J ) securing the cable on the gearbox assembly ( , ) L J ).
7. Disconnect the connector ( / ) L J ) from the starter ( 1 ) L J ).
8. Unscrew the nut ( 0 ) L J ) securing the rear positive cable to the starter ( 1 ) L J )
Page 1349 of 1659
L714 09 72 05
G )
) L J
) L J
) L J
'
(
%
A
C
® Automobili Lamborghini S.p.A. 7 K H L Q I R U P D W L R Q D Q G S U R F H G X U H V S X E O L V K H G E H O R Z D U H V W U L F W O \ F R Q ¿ G H Q W L D O D Q G H [ F O X V L Y H O \ I R U W K H / D P E R U J K L Q L ' H D O H U 1 H W Z R U N D Q G $ X W K R U L ] H G 6 H U Y L F H 3 R L Q W V $ O O F R S \ U L J K W V D U H S U R S H U W \ R I $ X W R P R E L O L
/ D P E R U J K L Q L 6 S $ E D V H G R Q F R S \ U L J K W O D Z $ O O R I W K H 3 ' ) F K D S W H U V L Q W K H : ( % Z R U N V K R S P D Q X D O V G H V F U L E H G E H O R Z D U H E D V H G R Q L Q I R U P D W L R Q D Y D L O D E O H D W W K H W L P H R I S X E O L F D W L R Q 7 K H F R P S D Q \ U H V H U Y H V
W K H U L J K W W R P D N H X S G D W H V D Q G P R G L ¿ F D W L R Q V 7 K H I R O O R Z L Q J D U H S U R K L E L W H G U H S U L Q W L Q J U H S U R G X F W L R Q I R U Z D U G L Q J W R X Q D X W K R U L ] H G S H R S O H D Q G R U W K L U G S D U W L H V D Q G W U D Q V O D W L R Q L Q F O X G L Q J S D U W L D O Z L W K R X W
Z U L W W H Q D X W K R U L ] D W L R Q I U R P $ X W R P R E L O L / D P E R U J K L Q L 6 S $
% $ V V H P E O L Q J W K H S R V L W L Y H E D W W H U \ F D E O H U H D U S D U W $ V V H P E O L Q J W K H S R V L W L Y H E D W W H U \ F D E O H U H D U S D U W1.
Tighten the nut ( B-Fig.7) securing the rear positive cable to the starter ( C-Fig.7).
2. Connect the connector ( A-Fig.7) to the starter ( C-Fig.7).
3 . Insert 3 clamps ( ' ) L J 8) to secure the cable to the wiring harness on the gearbox assembly ( ( ) L J 8).
4 . Connect the positive rear battery cable to the alternator ( ) ) L J 9) and tighten the nut ( * ) L J 9).
Page 1354 of 1659
2
L714 09 73 00
Fig.2
® Automobili Lamborghini S.p.A. 7 K H L Q I R U P D W L R Q D Q G S U R F H G X U H V S X E O L V K H G E H O R Z D U H V W U L F W O \ F R Q ¿ G H Q W L D O D Q G H [ F O X V L Y H O \ I R U W K H / D P E R U J K L Q L ' H D O H U 1 H W Z R U N D Q G $ X W K R U L ] H G 6 H U Y L F H 3 R L Q W V $ O O F R S \ U L J K W V D U H S U R S H U W \ R I $ X W R P R E L O L
/ D P E R U J K L Q L 6 S $ E D V H G R Q F R S \ U L J K W O D Z $ O O R I W K H 3 ' ) F K D S W H U V L Q W K H : ( % Z R U N V K R S P D Q X D O V G H V F U L E H G E H O R Z D U H E D V H G R Q L Q I R U P D W L R Q D Y D L O D E O H D W W K H W L P H R I S X E O L F D W L R Q 7 K H F R P S D Q \ U H V H U Y H V
W K H U L J K W W R P D N H X S G D W H V D Q G P R G L ¿ F D W L R Q V 7 K H I R O O R Z L Q J D U H S U R K L E L W H G U H S U L Q W L Q J U H S U R G X F W L R Q I R U Z D U G L Q J W R X Q D X W K R U L ] H G S H R S O H D Q G R U W K L U G S D U W L H V D Q G W U D Q V O D W L R Q L Q F O X G L Q J S D U W L D O Z L W K R X W
Z U L W W H Q D X W K R U L ] D W L R Q I U R P $ X W R P R E L O L / D P E R U J K L Q L 6 S $
0 $ ; , ) 8 6 ( % 2 ;
3 R V Value Function 3 R Z H U
1.200 A Maxi fuse box 30
2. 50 A A/C Fan – Seat Heating 30
3. 80 A Water Radiator Fans 30
4. 50 A Key, ILM(Lights), +75 30
5. 6. 7. 50 A Main fuse box 30
8. 60 A ESP 30
9. 100 A Engine/Gearbox 30
10. - Power windows, seats, lifting 30
Page 1379 of 1659
2
L714 09 81 00
Fig.2
LO 1
,H
,
H
O
1
L
M
3
MQ
Q
® Automobili Lamborghini S.p.A. 7 K H L Q I R U P D W L R Q D Q G S U R F H G X U H V S X E O L V K H G E H O R Z D U H V W U L F W O \ F R Q ¿ G H Q W L D O D Q G H [ F O X V L Y H O \ I R U W K H / D P E R U J K L Q L ' H D O H U 1 H W Z R U N D Q G $ X W K R U L ] H G 6 H U Y L F H 3 R L Q W V $ O O F R S \ U L J K W V D U H S U R S H U W \ R I $ X W R P R E L O L
/ D P E R U J K L Q L 6 S $ E D V H G R Q F R S \ U L J K W O D Z $ O O R I W K H 3 ' ) F K D S W H U V L Q W K H : ( % Z R U N V K R S P D Q X D O V G H V F U L E H G E H O R Z D U H E D V H G R Q L Q I R U P D W L R Q D Y D L O D E O H D W W K H W L P H R I S X E O L F D W L R Q 7 K H F R P S D Q \ U H V H U Y H V
W K H U L J K W W R P D N H X S G D W H V D Q G P R G L ¿ F D W L R Q V 7 K H I R O O R Z L Q J D U H S U R K L E L W H G U H S U L Q W L Q J U H S U R G X F W L R Q I R U Z D U G L Q J W R X Q D X W K R U L ] H G S H R S O H D Q G R U W K L U G S D U W L H V D Q G W U D Q V O D W L R Q L Q F O X G L Q J S D U W L D O Z L W K R X W
Z U L W W H Q D X W K R U L ] D W L R Q I U R P $ X W R P R E L O L / D P E R U J K L Q L 6 S $
Location of rear control units (Fig.2)
H.Cylinder bank 1-5 engine injection control unit(MASTER)
, Cylinder bank 6-10 engine injection control unit(SLAVE)
L.E-gear control unit
M. Fuse box
1 Yaw sensor control unit
O.
Bluetoothcontrol unit
3 Fuel pump control unit
Q. CD loader
Page 1444 of 1659
8
L714 10 90 00
Fig.9
A
B
® Automobili Lamborghini S.p.A. 7 K H L Q I R U P D W L R Q D Q G S U R F H G X U H V S X E O L V K H G E H O R Z D U H V W U L F W O \ F R Q ¿ G H Q W L D O D Q G H [ F O X V L Y H O \ I R U W K H / D P E R U J K L Q L ' H D O H U 1 H W Z R U N D Q G $ X W K R U L ] H G 6 H U Y L F H 3 R L Q W V $ O O F R S \ U L J K W V D U H S U R S H U W \ R I $ X W R P R E L O L
/ D P E R U J K L Q L 6 S $ E D V H G R Q F R S \ U L J K W O D Z $ O O R I W K H 3 ' ) F K D S W H U V L Q W K H : ( % Z R U N V K R S P D Q X D O V G H V F U L E H G E H O R Z D U H E D V H G R Q L Q I R U P D W L R Q D Y D L O D E O H D W W K H W L P H R I S X E O L F D W L R Q 7 K H F R P S D Q \ U H V H U Y H V
W K H U L J K W W R P D N H X S G D W H V D Q G P R G L ¿ F D W L R Q V 7 K H I R O O R Z L Q J D U H S U R K L E L W H G U H S U L Q W L Q J U H S U R G X F W L R Q I R U Z D U G L Q J W R X Q D X W K R U L ] H G S H R S O H D Q G R U W K L U G S D U W L H V D Q G W U D Q V O D W L R Q L Q F O X G L Q J S D U W L D O Z L W K R X W
Z U L W W H Q D X W K R U L ] D W L R Q I U R P $ X W R P R E L O L / D P E R U J K L Q L 6 S $
% D V L F V H W W L Q J S H U F H Q W U D O L Q D ( * ( $ 5
The “Basic setting” function allows you to make the initial settings on the selected control unit (E-GEAR).
The settings are divided into 7 different block numbers (Routines). Clutch Kiss Point Self tuning (Routine 1)
1 R W H
Routine 1 is performed when: • the clutch is replaced
• the E-gear control unit is replaced
• the gearbox is removed and reassembled
• Turn the ignition key to ON.
• Connect the computer to the diagnosis outlet OBDII
• Select routine 1 inside the block number ( A-Fig.9).
• Start the engine and bring water temperature to > 60°C.
• Start the connection (
) and press the start push-button ( B-Fig.9).
Routine 1 readapts the position of the clutch and calculates the correct Kiss Point value.
line 1 displays the operation result:
0 = positive result (Kiss Point successfully calculated)
255 = non-compliant result
line 2 displays the Kiss Point value at the end of the procedure
line 3 displays the engine speed, expressed in rpm
line 4 displays the clutch speed, expressed in rpm (the value ranges between 0 and 130); the speed at the time
when the clutch starts to transmit the engine’s motion.
The system performs the approach operation 10 times in order to properly calibrate the Kiss Point
value.
In order to store the Kiss Point value that has just been calculated in the system, turn the ignition key to OFF and
wait about one minute to allow the control unit to turn itself off (check this value in MWB 10).
: K H Q W K H S U R F H G X U H L V ¿ Q L V K H G W K H V \ V W H P D O Z D \ V D X W R P D W L F D O O \ U H V W R U H V W K H . L V V 3 R L Q W Y D O X H H Y H U \ W L P H W K H Y H K L F O H is started (when certain temperature and operating conditions are reached) to keep the pickup of the vehicle in
optimum condition according to clutch wear.
Page 1445 of 1659
9
L714 10 90 00
Fig.10
A
B
® Automobili Lamborghini S.p.A. 7 K H L Q I R U P D W L R Q D Q G S U R F H G X U H V S X E O L V K H G E H O R Z D U H V W U L F W O \ F R Q ¿ G H Q W L D O D Q G H [ F O X V L Y H O \ I R U W K H / D P E R U J K L Q L ' H D O H U 1 H W Z R U N D Q G $ X W K R U L ] H G 6 H U Y L F H 3 R L Q W V $ O O F R S \ U L J K W V D U H S U R S H U W \ R I $ X W R P R E L O L
/ D P E R U J K L Q L 6 S $ E D V H G R Q F R S \ U L J K W O D Z $ O O R I W K H 3 ' ) F K D S W H U V L Q W K H : ( % Z R U N V K R S P D Q X D O V G H V F U L E H G E H O R Z D U H E D V H G R Q L Q I R U P D W L R Q D Y D L O D E O H D W W K H W L P H R I S X E O L F D W L R Q 7 K H F R P S D Q \ U H V H U Y H V
W K H U L J K W W R P D N H X S G D W H V D Q G P R G L ¿ F D W L R Q V 7 K H I R O O R Z L Q J D U H S U R K L E L W H G U H S U L Q W L Q J U H S U R G X F W L R Q I R U Z D U G L Q J W R X Q D X W K R U L ] H G S H R S O H D Q G R U W K L U G S D U W L H V D Q G W U D Q V O D W L R Q L Q F O X G L Q J S D U W L D O Z L W K R X W
Z U L W W H Q D X W K R U L ] D W L R Q I U R P $ X W R P R E L O L / D P E R U J K L Q L 6 S $
Grid Self tuning (Routine 2)
1 R W H
Routine 2 is performed when: • the clutch is replaced
• the E-gear control unit is replaced
• the gearbox is removed and reassembled
• Turn the ignition key to ON.
• Connect the computer to the diagnosis outlet OBDII
• Select routine 2 inside the block number ( A-Fig.10).
• Start the connection (
) and press the start push-button ( B-Fig.10).
Routine 2 lets you set the engagement /selection grid regarding the gears.
line 1 the values “1” and “2” indicating the odd and even gears, respectively, that are engaged are displayed
intermittently during operation.
it displays the following values at the end of the operation:
14 = positive result (engagement /selection grid performed)
8 = non-compliant result (grid not performed due to electrical problems)
9 = non-compliant result (grid not performed because idle gears are not found)
line 2 displays the operation result:
0 = unacceptable grid
1 = acceptable grid
In order to store the grid value, turn the ignition key to OFF and wait for approx. 1 minute to allow the control unit to
turn off (check this value in MWB 64).
Page 1447 of 1659
11
L714 10 90 00
Abb.12
A
B
® Automobili Lamborghini S.p.A. 7 K H L Q I R U P D W L R Q D Q G S U R F H G X U H V S X E O L V K H G E H O R Z D U H V W U L F W O \ F R Q ¿ G H Q W L D O D Q G H [ F O X V L Y H O \ I R U W K H / D P E R U J K L Q L ' H D O H U 1 H W Z R U N D Q G $ X W K R U L ] H G 6 H U Y L F H 3 R L Q W V $ O O F R S \ U L J K W V D U H S U R S H U W \ R I $ X W R P R E L O L
/ D P E R U J K L Q L 6 S $ E D V H G R Q F R S \ U L J K W O D Z $ O O R I W K H 3 ' ) F K D S W H U V L Q W K H : ( % Z R U N V K R S P D Q X D O V G H V F U L E H G E H O R Z D U H E D V H G R Q L Q I R U P D W L R Q D Y D L O D E O H D W W K H W L P H R I S X E O L F D W L R Q 7 K H F R P S D Q \ U H V H U Y H V
W K H U L J K W W R P D N H X S G D W H V D Q G P R G L ¿ F D W L R Q V 7 K H I R O O R Z L Q J D U H S U R K L E L W H G U H S U L Q W L Q J U H S U R G X F W L R Q I R U Z D U G L Q J W R X Q D X W K R U L ] H G S H R S O H D Q G R U W K L U G S D U W L H V D Q G W U D Q V O D W L R Q L Q F O X G L Q J S D U W L D O Z L W K R X W
Z U L W W H Q D X W K R U L ] D W L R Q I U R P $ X W R P R E L O L / D P E R U J K L Q L 6 S $
Neutral Engagement (Routine 4)
1 R W H
Routine 4 is performed when: • the clutch is replaced
• the gearbox is removed and reassembled
• Turn the ignition key to OFF and wait about one minute to allow the control unit to turn itself off, then turn the
key back to ON.
• Connect the computer to the diagnosis outlet OBDII
• Select routine 4 inside the block number ( A-Fig.12).
• Start the connection (
) and press the start push-button ( B-Fig.12).
Routine 4 checks if the position of the idle gear is correct (the condition is checked only if a correct gear engagement
grid has been created – Routine 2 -).
riga 1 displays the operation result:
3 / 14 = gear in neutral
9 = idle gear not found
Page 1448 of 1659
12
L714 10 90 00
Fig.13
A
B
® Automobili Lamborghini S.p.A. 7 K H L Q I R U P D W L R Q D Q G S U R F H G X U H V S X E O L V K H G E H O R Z D U H V W U L F W O \ F R Q ¿ G H Q W L D O D Q G H [ F O X V L Y H O \ I R U W K H / D P E R U J K L Q L ' H D O H U 1 H W Z R U N D Q G $ X W K R U L ] H G 6 H U Y L F H 3 R L Q W V $ O O F R S \ U L J K W V D U H S U R S H U W \ R I $ X W R P R E L O L
/ D P E R U J K L Q L 6 S $ E D V H G R Q F R S \ U L J K W O D Z $ O O R I W K H 3 ' ) F K D S W H U V L Q W K H : ( % Z R U N V K R S P D Q X D O V G H V F U L E H G E H O R Z D U H E D V H G R Q L Q I R U P D W L R Q D Y D L O D E O H D W W K H W L P H R I S X E O L F D W L R Q 7 K H F R P S D Q \ U H V H U Y H V
W K H U L J K W W R P D N H X S G D W H V D Q G P R G L ¿ F D W L R Q V 7 K H I R O O R Z L Q J D U H S U R K L E L W H G U H S U L Q W L Q J U H S U R G X F W L R Q I R U Z D U G L Q J W R X Q D X W K R U L ] H G S H R S O H D Q G R U W K L U G S D U W L H V D Q G W U D Q V O D W L R Q L Q F O X G L Q J S D U W L D O Z L W K R X W
Z U L W W H Q D X W K R U L ] D W L R Q I U R P $ X W R P R E L O L / D P E R U J K L Q L 6 S $
Hydraulic circuit discharge (Routine 5)
1 R W H
Routine 5 is performed when:
• the E-gear oil level is checked
• gearbox is replaced
• the E-gear kit is replaced
• Turn the ignition key to OFF and wait about one minute to allow the control unit to turn itself off, then turn the
key back to ON.
• Connect the computer to the diagnosis outlet OBDII
• Select routine 5 inside the block number ( A-Fig.13).
• Start the connection (
) and press the start push-button ( B-Fig.13).
Routine 5 empties the pressure inside the E-gear circuit.
line 1 displays activation of the solenoid valve:
0 = not activated
1 = activated
line 2 displays the pressure value (during the pressure release phase, it continuously drops until it reaches
value 0)
line 3 displays the clutch status:
1 = activated
0 = not activated
line 4 displays the status of the hydraulic circuit:
1 = activated
0 = not activated
When the pressure reaches 0 bar, you can work on the circuit without risking pressure leaks.
1 R W H
Work on the circuit with the key OFF. If you turn the ignition key to ON, the system automatically brings pressure back inside the circuit.