2009 INFINITI QX56 wheel

ADP-24
< FUNCTION DIAGNOSIS >
AUTOMATIC DRIVE POSITIONER SYSTEM
EXIT ASSIST FUNCTION : Component Description
INFOID:0000000003775509
CONTROL UNITS
INPUT PARTS
Switches
Sensors
OUTPUT PARTS
ENTRY ASSIST FUNCTION
1. A. Automatic drive positioner control unit M33, M34
B. Pedal adjustin g motor assembly
E109, E110 2. A. Steering column
B. Key switch and ignition knob
switch M12
C. BCM M18, M19, M20 (view with
instrument panel removed) 3. A. Door mirror remo
te control switch
D10
B. Seat memory switch D5
4. Pedal adjusting switch M96 5 . A. Door mirrror LH D4, RH D107
B. Front door switch LH B 6. A. A/T selector lever
B. A/T shift selector (park position
switch) M203
7. A. Sliding motor LH B204 (driver seat
view), reclining motor LH B205, lift-
ing motor (front) B2 06, lifting motor
(rear) B207
B. Driver seat control unit B202,
B203
C. Power seat switch LH B208 8. A. ADP steering switch M16
B. Tilt sensor M85 and tilt motor M86
Item Function
Driver seat control unit  Operates the seat sliding motor for a constant amount.
 Driver seat control unit requests the operation of the tilt motor to the automatic
drive positioner control unit via UART communication.
Automatic drive positioner control unit Operates the tilt motor for a constant amount.
BCM Recognizes the following status and transmits it to the driver seat control unit via
CAN communication.
 Front door LH: OPEN/CLOSE
Item Function
Front door switch LH Detect front door LH open/close status.
Item Function
Sliding sensor Detect the front/rear position of seat.
Tilt sensor Detect the up/down position of steering wheel.
Item Function
Sliding motor Slide the seat forward/backward.
Tilt motor Moves the steering wheel upward/downward.
Revision: December 20092009 QX56

AUTOMATIC DRIVE POSITIONER SYSTEMADP-25
< FUNCTION DIAGNOSIS >
C
DE
F
G H
I
K L
M A
B
ADP
N
O P
ENTRY ASSIST FUNCTION : System DiagramINFOID:0000000003775510
ENTRY ASSIST FUNCTION : System DescriptionINFOID:0000000003775511
OUTLINE
The seat and steering wheel are in the exiting position when either following condition (A or B) is satisfied, the
seat and steering wheel return from exiting position to the previous driving position.
NOTE:
 This function is set to OFF before delivery (initial setting).
 Further information for the system setting procedure. Refer to Owner’s Manual.
OPERATION PROCEDURE
1. A: Turn the ignition switch ON. B: Turn the ignition switch from OFF to ACC after closing the driver door.
2. Front seat LH and steering wheel will return from the exiting position to entry position.
OPERATION CONDITION
Satisfy all of the following items. The entry assist f unction is not performed if these items are not satisfied.
DETAIL FLOW
ALJIA0238GB
Item Request status
Seat, steering wheel The vehicle is not moved after performing the
exit assist function.
Switch inputs
 Power seat switch
 Pedal adjusting switch
 ADP steering switch
 Door mirror control switch
 Set switch
 Memory switch OFF
(Not operated)
A/T selector lever P position
Revision: December 20092009 QX56

ADP-26
< FUNCTION DIAGNOSIS >
AUTOMATIC DRIVE POSITIONER SYSTEM
ENTRY ASSIST FUNCTION : Component Parts Location
INFOID:0000000004055688
Order Input Output Control unit condition 1 Door switch/Ignition
switch —
Driver seat control unit receives the signals of ignition switch signal
and front door switch from BCM via CAN communication.
2 — Motors (sliding, tilt) Driver seat control unit operates the sliding motor when the operating
conditions are satisfied. Driver seat control unit then requests the op-
eration of the tilt motor to the automatic drive positioner control unit
via UART communication. The automatic drive positioner control unit
operates the motor for a constant amount.
Sensors (sliding, tilt) — Sensors monitor the operating positions of seat and steering wheel
and then stops the operation of each motor when each part reaches
the recorded address.
ALJIA0347ZZ
1. A. Automatic drive positioner control
unit M33, M34
B. Pedal adjustin g motor assembly
E109, E110 2. A. Steering column
B. Key switch and ignition knob
switch M12
C. BCM M18, M19, M20 (view with
instrument panel removed) 3. A. Door mirror remo
te control switch
D10
B. Seat memory switch D5
4. Pedal adjusting switch M96 5 . A. Door mirrror LH D4, RH D107
B. Front door switch LH B 6. A. A/T selector lever
B. A/T shift selector (park position
switch) M203
7. A. Sliding motor LH B204 (driver seat
view), reclining motor LH B205, lift-
ing motor (front) B2 06, lifting motor
(rear) B207
B. Driver seat control unit B202,
B203
C. Power seat switch LH B208 8. A. ADP steering switch M16
B. Tilt sensor M85 and tilt motor M86
Revision: December 20092009 QX56

AUTOMATIC DRIVE POSITIONER SYSTEMADP-27
< FUNCTION DIAGNOSIS >
C
DE
F
G H
I
K L
M A
B
ADP
N
O P
ENTRY ASSIST FUNCTION : Component DescriptionINFOID:0000000003775513
CONTROL UNITS
INPUT PARTS
Switches
Sensors
OUTPUT PARTS
Item Function
Driver seat control unit According to the ignition signal and front door switch LH signal from BCM,
 Operates the seat sliding motor for a constant amount.
 Driver seat control unit then requests the operation of the tilt motor to the auto-
matic drive positioner control unit via UART communication.
Automatic drive positioner control unit Operates the tilt motor for a constant amount.
BCM Recognizes the following status and transmits it to the driver seat control unit via
CAN communication.
 Front door LH: OPEN/CLOSE
 Ignition switch position: ACC/ON
Item Function
Front door switch LH Detect front door LH open/close status.
Item Function
Sliding sensor Detect the front/rear position of seat.
Tilt sensor Detect the up/down position of steering wheel.
Item Function
Sliding motor Slide the seat forward/backward.
Tilt motor Moves the steering wheel upward/downward.
Revision: December 20092009 QX56

ADP-58
< COMPONENT DIAGNOSIS >
TILT SWITCH
Is the inspection result normal?
YES >> GO TO 3
NO >> Repair or replace harness.
3. CHECK ADP STEERING SWITCH GROUND CIRCUIT
Check continuity between ADP steering switch connector M16 termi-
nal 1 and ground.
Is the inspection result normal?
YES >> Check the condition of the harness and connector.
NO >> Replace or replace harness.
4. CHECK TILT SWITCH
Refer to ADP-58, "Component Inspection"
.
Is the inspection result normal?
YES >> GO TO 5
NO >> Replace ADP steering switch. Refer to ADP-170, "Removal and Installation"
.
5. CHECK INTERMITTENT INCIDENT
Refer to GI-38, "Intermittent Incident"
.
Is the inspection result normal?
YES >> Replace automatic drive posit ioner control unit. Refer to ADP-166, "Removal and Installation".
NO >> Repair or replace the malfunctioning part.
Component InspectionINFOID:0000000003775572
1. CHECK ADP STEERING WHEEL TILT SWITCH
Check continuity between ADP steering switch terminals as follows.
Is the inspection result normal?
YES >> Inspection End.
NO >> Replace ADP steering switch. Refer to ADP-170,
"Removal and Installation".
1 - Ground : Continuity should not exist.
17 - Ground : Continuity should not exist.
1 - Ground : Continuity should exist.
LIIA0490E
Terminals Condition Continuity
2 1ADP steering switch ON (UP operation) Yes
Other than above No
3 ADP steering switch ON (DOWN operation) Yes
Other than above No
LIIA1435E
Revision: December 20092009 QX56

ADP SYSTEM SYMPTOMSADP-159
< SYMPTOM DIAGNOSIS >
C
DE
F
G H
I
K L
M A
B
ADP
N
O P
SYMPTOM DIAGNOSIS
ADP SYSTEM SYMPTOMS
Symptom TableINFOID:0000000003775657
NOTE:
Always perform the “Basic Inspection” before perfo rming diagnosis in the following table. Refer to ADP-5,
"Work Flow".
SYMPTOM 1
SYMPTOM 2
SYMPTOM 3
Symptom Diagnosis procedure Reference
page
Manual functions (for specific part) do
not operate Sliding operation Check sliding switch.
ADP-49
Reclining operation Check reclining switch.ADP-51
Lifting operation (front) Check lifting switch (front).ADP-53
Lifting operation (rear) Check lifting switch (rear).ADP-55
Pedal operation1. Check pedal adjusting switch.
ADP-592. Check pedal adjusting sensor.ADP-84
Steering wheel tilt operation Check ADP steering switch ADP-57
Door mirror operation1. Changeover switch.
ADP-642. Mirror switchADP-66
All parts of seatCheck power seat switch ground cir-
cuit. ADP-69
Symptom Diagnosis procedure Reference
page
Memory functions (for specific part) do
not operate Sliding operation Check sliding sensor.
ADP-74
Reclining operation Check reclining sensor.ADP-76
Lifting operation (front) Check lifting sensor (front).ADP-78
Lifting operation (rear) Check lifting sensor (rear).ADP-80
Pedal operation Check pedal adjusting sensor.ADP-84
Steering wheel tilt operation Check tilt sensorADP-82
Door mirror operation Check door mirror sensor. Driver side:
ADP-86Passenger side:
ADP-88
Symptom Diagnosis procedure Reference
page
Memory functions and manual func-
tions (for specific part) do not operate Sliding operation Check sliding motor.
ADP-90
Reclining operation Check reclining motor.ADP-92
Lifting operation (front) Check lifting motor (front).ADP-94
Lifting operation (rear) Check lifting motor (rear).ADP-96
Pedal operation Check pedal adjusting motor.ADP-100
Steering wheel operation Check tilt motor ADP-98
Door mirror operation Check door mirror motor.ADP-102
Revision: December 20092009 QX56

ADP-162
< PRECAUTION >
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000005848468
The Supplemental Restraint System such as “A IR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severi ty of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and w hether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SR and SB section of this Service Man-
ual.
WARNING:
• To avoid rendering the SRS inopera tive, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISS AN/INFINITI dealer.
 Improper maintenance, including in correct removal and installation of the SRS, can lead to personal
injury caused by unintent ional activation of the system. For re moval of Spiral Cable and Air Bag
Module, see the SR section.
 Do not use electrical test equipmen t on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identi fied by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
 When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electri c power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor( s) and deploy the air bag(s), possibly causing
serious injury.
 When using air or electric power tools or hammers , always switch the Ignition OFF, disconnect the
battery, and wait at least 3 minu tes before performing any service.
Precaution Necessary for Steering W heel Rotation After Battery Disconnect
INFOID:0000000005851835
NOTE:
 This Procedure is applied only to models with Intelli gent Key system and NATS (NISSAN ANTI-THEFT SYS-
TEM).
 Remove and install all control units after disconnecting both battery cables with the ignition knob in the
″LOCK ″ position.
 Always use CONSULT-III to perform self-diagnosis as a part of each function inspection after finishing work.
If DTC is detected, perform trouble diagnosis according to self-diagnostic results.
For models equipped with the Intelligent Key system and NATS, an electrically controlled steering lock mech-
anism is adopted on the key cylinder.
For this reason, if the battery is disconnected or if the battery is discharged, the steering wheel will lock and
steering wheel rotation will become impossible.
If steering wheel rotation is required when battery pow er is interrupted, follow the procedure below before
starting the repair operation.
OPERATION PROCEDURE
1. Connect both battery cables. NOTE:
Supply power using jumper cables if battery is discharged.
2. Use the Intelligent Key or mechanical key to turn the ignition switch to the ″ACC ″ position. At this time, the
steering lock will be released.
3. Disconnect both battery cables. The steering lock will remain released and the steering wheel can be
rotated.
4. Perform the necessary repair operation.
Revision: December 20092009 QX56

AV
AV-3
C
DE
F
G H
I
J
K L
M B
A
O P
Description ..........................................................
....
80
Diagnosis Procedure ...............................................80
RGB AREA (YS) SIGNAL CIRCUIT ..................81
Description .......................................................... ....81
Diagnosis Procedure ...............................................81
HORIZONTAL SYNCHRONIZING (HP) SIG-
NAL CIRCUIT ................................................. ....
82
Description .......................................................... ....82
Diagnosis Procedure ...............................................82
VERTICAL SYNCHRONIZING (VP) SIGNAL
CIRCUIT ......................................................... ....
83
Description .......................................................... ....83
Diagnosis Procedure ...............................................83
FRONT DOOR SPEAKER .................................84
Description .......................................................... ....84
Diagnosis Procedure ...............................................84
FRONT TWEETER .............................................87
Description .......................................................... ....87
Diagnosis Procedure ...............................................87
CENTER SPEAKER ...........................................90
Description .......................................................... ....90
Diagnosis Procedure ...............................................90
REAR DOOR SPEAKER ....................................92
Description .......................................................... ....92
Diagnosis Procedure ...............................................92
REAR DOOR TWEETER ...................................95
Description .......................................................... ....95
Diagnosis Procedure ...............................................95
BACK DOOR SPEAKER ...................................98
Description .......................................................... ....98
Diagnosis Procedure ...............................................98
SUBWOOFER ..................................................101
Description .......................................................... ..101
Diagnosis Procedure .............................................101
AMP ON SIGNAL CIRCUIT .............................104
Description .......................................................... ..104
Diagnosis Procedure .............................................104
STEERING SWITCH ........................................105
Description .......................................................... ..105
Diagnosis Procedure .............................................105
MICROPHONE SIGNAL CIRCUIT ...................107
Description .......................................................... ..107
Diagnosis Procedure .............................................107
ECU DIAGNOSIS .......................................109
AV CONTROL UNIT ....................................... ..109
Reference Value ................................................. ..109
Wiring Diagram .....................................................115
DTC Index ........................................................... ..143
DISPLAY UNIT ................................................145
Reference Value ....................................................145
BOSE SPEAKER AMP ...................................148
Reference Value ....................................................148
REAR VIEW CAMERA CONTROL UNIT .......151
Reference Value ....................................................151
DVD PLAYER ..................................................153
Reference Value ....................................................153
SYMPTOM DIAGNOSIS ............................155
MULTI AV SYSTEM ........................................155
Symptom Table ................................................... ..155
NORMAL OPERATING CONDITION .............157
Description .............................................................157
PRECAUTION ............................................165
PRECAUTIONS ...............................................165
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ............................................................. ..
165
Precaution Necessary for Steering Wheel Rota-
tion After Battery Disconnect .................................
165
PREPARATION .........................................167
PREPARATION ...............................................167
Commercial Service Tools ................................... ..167
ON-VEHICLE REPAIR ...............................168
AV CONTROL UNIT ........................................168
Removal and Installation ..................................... ..168
DISPLAY UNIT ................................................170
Removal and Installation .......................................170
FRONT TWEETER ..........................................171
Removal and Installation .......................................171
CENTER SPEAKER ........................................172
Removal and Installation .......................................172
FRONT DOOR SPEAKER ..............................173
Removal and Installation .......................................173
REAR DOOR SPEAKER ................................174
Removal and Installation .......................................174
BACK DOOR SPEAKER ................................175
Removal and Installation .......................................175
SUBWOOFER .................................................176
Removal and Installation .......................................176
DVD PLAYER ..................................................177
Removal and Installation .......................................177
Revision: December 20092009 QX56