2009 HUMMER H3 check engine

Additional Required Services (cont’d)
Service and Miles (Kilometers)25,000
(40 000) 50,000
(80 000) 75,000
(120 000) 100,000
(160 000) 125,000
(200 000) 150,000
(240 000)
Engine cooling system service (or every
ve years, whichever occurs rst).
An Emission Control Service.
See footnote (i). •
Inspect engine accessory drive belt.
An Emission Control Service.
See footnote (k). •
Maintenance Footnotes
#
Lubricate the front suspension,
steering linkage, and parking brake
cable guides. Control arm ball
joints require lubrication but should
not be lubricated unless their
temperature is 10°F (-12°C) or
higher, or they could be damaged.
(a) Visually inspect brake lines
and hoses for proper hook-up,
binding, leaks, cracks, chafing, etc.
Inspect disc brake pads for wear
and rotors for surface condition.
Inspect other brake parts, including
calipers, parking brake, etc. (b)
Visually inspect front and rear
suspension and steering system
for damaged, loose, or missing
parts, signs of wear or lack
of lubrication. Inspect power steering
lines and hoses for proper hook-up,
binding, leaks, cracks, chafing,
etc. Visually check constant velocity
joints, rubber boots and axle
seals for leaks. Rotate and inspect
U-joints, retainers, and bolts on
rear drive shaft for seizing or
loosening. (c)
Visually inspect hoses and have
them replaced if they are cracked,
swollen, or deteriorated. Inspect
all pipes, fittings, and clamps;
replace with genuine parts as
needed. To help ensure proper
operation, a pressure test of
the cooling system and pressure
cap and cleaning the outside of
the radiator and air conditioning
condenser is recommended at least
once a year.
Maintenance Schedule 6-7

(d)Inspect wiper blades for wear,
cracking, or contamination.
Clean the windshield and wiper
blades, if contaminated. Replace
wiper blades that are worn or
damaged. See Windshield Wiper
Blade Replacement on page 5-44
and Windshield, Backglass,
and Wiper Blades on page 5-87
for more information.
(e)Make sure the safety belt
reminder light and safety belt
assemblies are working properly.
Look for any other loose or
damaged safety belt system parts.
If you see anything that might
keep a safety belt system from doing
its job, have it repaired. Have any
torn or frayed safety belts replaced.
Also see Checking the Restraint
Systems on page 1-60.
(f)Lubricate all key lock cylinders,
hood latch assembly, secondary
latch, pivots, spring anchor, release
pawl, rear compartment hinges,
outer endgate handle pivot points,
rear door detent link, rollermechanism, endgate handle pivot
points, latch bolt, fuel door hinge,
locks, and folding seat hardware.
More frequent lubrication may
be required when exposed to a
corrosive environment. Applying
silicone grease on weatherstrips
with a clean cloth will make
them last longer, seal better, and
not stick or squeak.
(g)Check vent hose at transfer
case for kinks and proper
installation.
(h)Change automatic transmission
fluid and filter if the vehicle is
mainly driven under one or more of
these conditions:
In heavy city traffic where the
outside temperature regularly
reaches 90°F (32°C) or higher.
In hilly or mountainous terrain.
When doing frequent trailer
towing.
Uses such as found in taxi,
police, or delivery service.(i)Drain, flush, and refill cooling
system. This service can be
complex; you should have your
dealer/retailer perform this service.
See Engine Coolant on page 5-23
for what to use. Inspect hoses.
Clean radiator, condenser,
pressure cap, and filler neck.
Pressure test the cooling system
and pressure cap.
(j)A fluid loss in any vehicle system
could indicate a problem. Have the
system inspected and repaired
and the fluid level checked. Add fluid
if needed.
(k)Visually inspect belt for fraying,
excessive cracks, or obvious
damage. Replace belt if necessary.
6-8 Maintenance Schedule

Owner Checks and
Services
These owner checks and services
should be performed at the
intervals specied to help ensure
vehicle safety, dependability,
and emission control performance.
Your dealer/retailer can assist
with these checks and services.
Be sure any necessary repairs are
completed at once. Whenever
any uids or lubricants are added
to the vehicle, make sure they
are the proper ones, as shown
inRecommended Fluids and
Lubricants on page 6-12.
At Each Fuel Fill
It is important to perform these
underhood checks at each fuel fill.
Engine Oil Level Check
Notice:It is important to check
the engine oil regularly and
keep it at the proper level.
Failure to keep the engine oil
at the proper level can cause
damage to the engine not covered
by the vehicle warranty.
Check the engine oil level and
add the proper oil if necessary.
SeeEngine Oil on page 5-13.
Engine Coolant Level Check
Check the engine coolant level
and add DEX-COOL®coolant
mixture if necessary. SeeEngine
Coolant on page 5-23.
Windshield Washer Fluid
Level Check
Check the windshield washer uid
level in the windshield washer
uid reservoir and add the proper
uid if necessary.
At Least Once a Month
Tire Ination Check
Inspect the vehicle’s tires and make
sure they are inated to the correct
pressures. Do not forget to check
the spare tire. SeeInflation - Tire
Pressure on page 5-51. Check to
make sure the spare tire is stored
securely. SeeChanging a Flat Tire
on page 5-66.
Tire Wear Inspection
Tire rotation may be required for
high mileage highway drivers prior to
the Engine Oil Life System service
notication. Check the tires for
wear and, if necessary, rotate the
tires. SeeTire Inspection and
Rotation on page 5-57.
Maintenance Schedule 6-9

At Least Once a Year
Starter Switch Check
{CAUTION
When you are doing this
inspection, the vehicle could move
suddenly. If the vehicle moves,
you or others could be injured.
1. Before starting this check, be
sure there is enough room
around the vehicle.
2. Firmly apply both the parking
brake and the regular brake.
SeeParking Brake on page 2-28.
Do not use the accelerator
pedal, and be ready to turn off
the engine immediately if it starts.3. For automatic transmission
vehicles, try to start the engine
in each gear. The vehicle
should start only in P (Park) or
N (Neutral). If the vehicle starts
in any other position, contact
your dealer/retailer for service.
For manual transmission
vehicles, put the shift lever in
Neutral, push the clutch
pedal down halfway, and try to
start the engine. The vehicle
should start only when the clutch
pedal is pushed down all the
way to the oor. If the vehicle
starts when the clutch pedal
is not pushed all the way down,
contact your dealer/retailer
for service.
Automatic Transmission Shift
Lock Control System Check
{CAUTION
When you are doing this
inspection, the vehicle could move
suddenly. If the vehicle moves,
you or others could be injured.
1. Before starting this check, be
sure there is enough room
around the vehicle. It should be
parked on a level surface.
2. Firmly apply the parking brake.
SeeParking Brake on page 2-28.
Be ready to apply the regular
brake immediately if the vehicle
begins to move.
3. With the engine off, turn the
ignition to ON/RUN, but do not
start the engine. Without applying
the regular brake, try to move
the shift lever out of P (Park) with
normal effort. If the shift lever
moves out of P (Park), contact
your dealer/retailer for service.
6-10 Maintenance Schedule

Ignition Transmission Lock
Check
While parked, and with the parking
brake set, try to turn the ignition
to LOCK/OFF in each shift lever
position.
For automatic transmission
vehicles, the ignition should turn
to LOCK/OFF only when the
shift lever is in P (Park).
The ignition key should
come out only in LOCK/OFF.
For manual transmission
vehicles, the ignition key should
come out only in LOCK/OFF.
Contact your dealer/retailer if service
is required.
Parking Brake and Automatic
Transmission P (Park)
Mechanism Check
{CAUTION
When you are doing this check,
the vehicle could begin to move.
You or others could be injured
and property could be damaged.
Make sure there is room in front
of the vehicle in case it begins to
roll. Be ready to apply the regular
brake at once should the vehicle
begin to move.
Park on a fairly steep hill, with the
vehicle facing downhill. Keeping
your foot on the regular brake, set
the parking brake.
To check the parking brake’s
holding ability: With the engine
running and transmission in
N (Neutral), slowly remove footpressure from the regular brake
pedal. Do this until the vehicle
is held by the parking brake only.
To check the P (Park)
mechanism’s holding ability:
With the engine running, shift to
P (Park). Then release the
parking brake followed by the
regular brake.
Contact your dealer/retailer if
service is required.
Underbody Flushing Service
At least every spring, use plain
water to ush any corrosive
materials from the underbody.
Take care to clean thoroughly
any areas where mud and other
debris can collect.
Maintenance Schedule 6-11

ORDER TOLL FREE:
1-800-551-4123 Monday-Friday
8:00 AM - 6:00 PM Eastern Time
For Credit Card Orders Only
(VISA-MasterCard-Discover), visit
Helm, Inc. on the World Wide
Web at: helminc.com
Or you can write to:
Helm, Incorporated
P.O. Box 07130
Detroit, MI 48207
Prices are subject to change without
notice and without incurring
obligation. Allow ample time for
delivery.
Note to Canadian Customers: All
listed prices are quoted in U.S.
funds. Canadian residents are to
make checks payable in U.S. funds.Vehicle Data
Recording and
Privacy
Your GM vehicle has a number of
sophisticated computers that record
information about the vehicle’s
performance and how it is driven. For
example, your vehicle uses computer
modules to monitor and control
engine and transmission
performance, to monitor the
conditions for airbag deployment and
deploy airbags in a crash and, if so
equipped, to provide antilock braking
to help the driver control the vehicle.
These modules may store data to
help your dealer/retailer technician
service your vehicle. Some modules
may also store data about how you
operate the vehicle, such as rate of
fuel consumption or average speed.
These modules may also retain the
owner’s personal preferences, such
as radio pre-sets, seat positions, and
temperature settings.
Event Data Recorders
This vehicle has an Event
Data Recorder (EDR). The main
purpose of an EDR is to record, in
certain crash or near crash-like
situations, such as an airbag
deployment or hitting a road
obstacle, data that will assist in
understanding how a vehicle’s
systems performed. The EDR is
designed to record data related to
vehicle dynamics and safety
systems for a short period of time,
typically 30 seconds or less.
The EDR in this vehicle is designed
to record such data as:
How various systems in your
vehicle were operating
Whether or not the driver and
passenger safety belts were
buckled/fastened
How far, if at all, the driver was
pressing the accelerator and/or
brake pedal
How fast the vehicle was
traveling
7-16 Customer Assistance Information

Audio System(s)..................3-42
Automatic Headlamp
System...........................3-14
Automatic Transmission
Fluid...............................5-18
Operation........................2-19
B
Battery...............................5-33
Electric Power
Management.................3-17
Run-Down Protection.........3-17
Bench Seat,
Split (60/40)................1-7, 1-9
Bluetooth
®..........................3-52
Brake
Emergencies...................... 4-6
Brake Fluid.........................5-30
Brakes...............................5-30
System Warning Light.......3-27
Braking................................ 4-3
Braking in Emergencies.......... 4-6
Break-In, New Vehicle..........2-15
Bulb Replacement................5-41
Halogen Bulbs..................5-41
Headlamp Aiming..............5-39
Headlamps......................5-41Bulb Replacement (cont.)
License Plate Lamps.........5-43
Replacement Bulbs...........5-43
Taillamps, Turn Signal,
Stoplamps and Back-up
Lamps .........................5-42
Buying New Tires.................5-59
C
Calibration..........................2-34
California Fuel....................... 5-5
California Perchlorate
Materials Requirements....... 5-4
California Proposition
65 Warning........................ 5-4
Canadian Owners..................... ii
Capacities and
Specications...................5-96
Carbon Monoxide....2-7, 2-9, 2-31
Care of
Safety Belts.....................5-85
Cargo Cover.......................2-49
Cargo Management System . . . 2-49
Cargo Tie Downs.................2-49
Center Console
Storage Area....................2-47
Chains, Tire........................5-65
Charging System Light..........3-27Check
Engine Lamp...................3-30
Checking Things Under
the Hood ........................... 5-9
Chemical Paint Spotting........5-90
Child Restraints
Child Restraint Systems.....1-31
Infants and Young
Children.......................1-28
Lower Anchors and Tethers
for Children..................1-34
Older Children..................1-25
Securing a Child Restraint
in a Rear Outside Seat
Position.......................1-41
Securing a Child Restraint
in the Center Rear Seat
Position.......................1-43
Securing a Child Restraint
in the Right Front Seat
Position.......................1-43
Where to Put the
Restraint......................1-32
Cigarette Lighter..................3-18
Cleaning
Aluminum or
Chrome-Plated Wheels . . . 5-88
Exterior Lamps/Lenses......5-86
Fabric/Carpet...................5-84
i-2 INDEX

Driving (cont.)
Hill and Mountain Roads....4-30
In Rain and on
Wet Roads...................4-29
Off-Road .........................4-13
Recovery Loops...............4-34
Rocking Your Vehicle to
Get it Out ....................4-34
Winter.............................4-31
Driving for Better Fuel
Economy........................... 4-1
E
EDR ..................................7-16
Electrical System
Add-On Equipment............5-91
Engine Compartment Fuse
Block...........................5-92
Fuses and Circuit
Breakers......................5-91
Power Windows and Other
Power Options..............5-91
Windshield Wiper Fuses....5-91
Electronic Immobilizer
PASS-Key
®III+................2-13Electronic Immobilizer
Operation
PASS-Key
®III+................2-14
Engine
Air Cleaner/Filter...............5-17
Check and Service Engine
Soon Lamp..................3-30
Coolant...........................5-23
Coolant Heater.................2-19
Coolant
Temperature Gage.........3-29
Drive Belt Routing.............6-15
Engine Compartment
Overview......................5-10
Exhaust...........................2-31
Fan Noise.......................5-28
Oil ..................................5-13
Oil Life System.................5-15
Overheating.....................5-27
Starting...........................2-17
Event Data Recorders..........7-16
Exit Lighting........................3-16
Extender, Safety Belt............1-25
Exterior Lamps....................3-11
F
Filter
Engine Air Cleaner............5-17
Finish Damage....................5-89
Fixed Mast Antenna.............3-63
Flashers, Hazard Warning....... 3-5
Flash-to-Pass........................ 3-7
Flat Tire..............................5-66
Flat Tire, Changing...............5-66
Flat Tire, Storing..........5-78, 5-80
Fluid
Automatic Transmission.....5-18
Power Steering.................5-29
Windshield Washer...........5-30
Fog Lamp
Fog ................................3-15
Four-Wheel Drive.................5-38
Four-Wheel Drive,
Full-Time.........................2-24
Front Axle...........................5-39
Front Seat Storage Net.........2-47
Fuel..................................... 5-5
Additives........................... 5-6
California Fuel................... 5-5
Driving for Better
Economy....................... 4-1
i-4 INDEX