2009 HUMMER H3 sensor

Tire Pressure Monitor
Operation
This vehicle may have a Tire
Pressure Monitor System (TPMS).
The TPMS is designed to warn
the driver when a low tire pressure
condition exists. TPMS sensors
are mounted onto each tire and
wheel assembly on the vehicle,
excluding the spare tire. The TPMS
sensors monitor the air pressure
in the vehicle’s tires and transmit the
tire pressure readings to a receiver
located in the vehicle.
When a low tire pressure condition
is detected, the TPMS illuminates
the low tire pressure warning light
located on the instrument panel
cluster.At the same time, a Driver
Information Center (DIC) message
is displayed on the DIC display
screen. The low tire pressure
warning light and the DIC warning
message come on at each
ignition cycle until the tires are
inated to the correct ination
pressure. For additional information
and details about the DIC operation
and displays seeDIC Operation and
Displays on page 3-34andDIC
Warnings and Messages on
page 3-37.
The low tire pressure warning light
may come on in cool weather
when the vehicle is rst started, and
then turn off as you start to drive.
This could be an early indicator that
the air pressure in the tire(s) are
getting low and need to be inated
to the proper pressure.A Tire and Loading Information
label, attached to the vehicle, shows
the size of the vehicle’s original
equipment tires and the correct
ination pressure for the vehicle’s
tires when they are cold. See
Loading the Vehicle on page 4-35,
for an example of the Tire and
Loading Information label and its
location on the vehicle. Also see
Inflation - Tire Pressure on
page 5-51.
The vehicle’s TPMS can warn you
about a low tire pressure condition
but it does not replace normal
tire maintenance. SeeTire
Inspection and Rotation on
page 5-57andTires on page 5-44.
Notice:Liquid tire sealants
could damage the Tire Pressure
Monitor System (TPMS) sensors.
Sensor damage caused by using
a tire sealant is not covered
by your warranty. Do not use
liquid tire sealants.
5-54 Service and Appearance Care

TPMS Malfunction Light
and Message
The TPMS will not function properly
if one or more of the TPMS
sensors are missing or inoperable.
When the system detects a
malfunction, the low tire warning
light ashes for about one minute
and then stays on for the remainder
of the ignition cycle. A DIC warning
message is also displayed. The low
tire warning light and DIC warning
message come on at each ignition
cycle until the problem is corrected.
Some of the conditions that can
cause the malfunction light and
DIC message to come on are:
One of the road tires has been
replaced with the spare tire.
The spare tire does not have a
TPMS sensor. The TPMS
malfunction light and DIC
message should go off once you
re-install the road tire containing
the TPMS sensor.
The TPMS sensor matching
process was started but not
completed or not completed
successfully after rotating the
vehicle’s tires. The DIC message
and TPMS malfunction light
should go off once the TPMS
sensor matching process is
performed successfully.
See “TPMS Sensor Matching
Process” later in this section.
One or more TPMS sensors are
missing or damaged. The DIC
message and the TPMS
malfunction light should go off
when the TPMS sensors are
installed and the sensor
matching process is performed
successfully. See your
dealer/retailer for service.
Replacement tires or wheels do
not match the vehicle’s original
equipment tires or wheels. Tires
and wheels other than those
recommended for the vehicle
could prevent the TPMS from
functioning properly. SeeBuying
New Tires on page 5-59.
Operating electronic devices or
being near facilities using radio
wave frequencies similar to the
TPMS could cause the TPMS
sensors to malfunction.
If the TPMS is not functioning it
cannot detect or signal a low
tire condition. See your
dealer/retailer for service if the
TPMS malfunction light and
DIC message comes on and
stays on.
Service and Appearance Care 5-55

TPMS Sensor Matching
Process
Each TPMS sensor has a unique
identication code. Any time
you replace one or more of the
TPMS sensors or rotate the
vehicle’s tires, the identication
codes need to be matched to the
new tire/wheel position. The sensors
are matched to the tire/wheel
positions in the following order:
driver side front tire, passenger side
front tire, passenger side rear
tire, and driver side rear tire using a
TPMS diagnostic tool. See your
dealer/retailer for service.
The TPMS sensors can also be
matched to each tire/wheel position
by increasing or decreasing the
tire’s air pressure. If increasing the
tire’s air pressure, do not exceed
the maximum ination pressure
indicated on the tire’s sidewall.
To let air-pressure out of a tire you
can use the pointed end of the
valve cap, a pencil-style air pressure
gage, or a key.You have one minute to match
the rst tire/wheel position,
and ve minutes overall, to match
all four tire/wheel positions. If it
takes longer than one minute, to
match the rst tire and wheel,
or more than ve minutes to match
all four tire and wheel positions,
the matching process stops and you
need to start over.
The TPMS sensor matching
procedure is outlined below:
1. Set the parking brake.
2. Turn the ignition switch to
ON/RUN with the engine off.
3. Turn the exterior lamp switch
from AUTO to OFF four times
within three seconds. A double
horn chirp will sound and
the TPMS low tire warning light
starts ashing. The double
horn chirp and ashing TPMS
warning light indicates the
TPMS matching process has
started. The TPMS warning
light should continue ashingthroughout the matching
procedure. The LOW TIRE
message displays on the Driver
Information Center (DIC).
4. Start with the driver side front tire.
5. Remove the valve cap from the
valve cap stem. Activate the
TPMS sensor by increasing or
decreasing the tire’s air pressure
for 10 seconds, then stop and
listen for a single horn chirp.
The single horn chirp should
sound within 15 seconds,
conrming that the sensor
identication code has been
matched to this tire and wheel
position. If you do not hear
the conrming single horn chirp,
turn the ignition switch to
LOCK and start over beginning
with Step 2.
6. Proceed to the passenger side
front tire, and repeat the
procedure in Step 5.
7. Proceed to the passenger side
rear tire, and repeat the
procedure in Step 5.
5-56 Service and Appearance Care

8. Proceed to the driver side rear
tire, and repeat the procedure
in Step 5.
9. After hearing the conrming horn
chirp for the driver side rear tire,
check to see if the TPMS low tire
warning light and the DIC LOW
TIRE messages have turned off.
If yes, the TPMS sensors have
been relearned. Turn the ignition
switch to LOCK/OFF.
If the low tire warning light and
the SERV TPM message on the
DIC are on after completing
Step 5 for the driver side rear tire,
the sensor relearn process has
not been successful. Turn the
ignition switch to LOCK/OFF and
repeat the matching process
beginning with Step 2.
10. Set all four tires to the
recommended air pressure level
as indicated on the Tire and
Loading Information label.
11. Put the valve caps back on the
valve stems.Tire Inspection and
Rotation
We recommend that you
regularly inspect the vehicle’s
tires, including the spare tire,
for signs of wear or damage.
SeeWhen It Is Time for
New Tires on page 5-58for
more information.
Tires should be rotated
every 5,000 to 8,000 miles
(8 000 to 13 000 km).
SeeScheduled Maintenance
on page 6-4.
The purpose of a regular tire
rotation is to achieve a uniform
wear for all tires on the vehicle.
This will ensure that the
vehicle continues to perform
most like it did when the
tires were new.Any time you notice unusual
wear, rotate the tires as soon
as possible and check wheel
alignment. Also check for
damaged tires or wheels.
SeeWhen It Is Time for
New Tires on page 5-58and
Wheel Replacement on
page 5-64.
Make sure the spare tire is
stored securely. Push, pull and
then try to rotate or turn the
tire. If it moves, use the wheel
wrench/hoist shaft to tighten
the cable. SeeChanging a
Flat Tire on page 5-66.
Service and Appearance Care 5-57

Wheel Replacement
Replace any wheel that is bent,
cracked, or badly rusted or corroded.
If wheel nuts keep coming loose, the
wheel, wheel bolts, and wheel nuts
should be replaced. If the wheel
leaks air, replace it (except some
aluminum wheels, which can
sometimes be repaired). See your
dealer/retailer if any of these
conditions exist.
Your dealer/retailer will know the
kind of wheel you need.
Each new wheel should have the
same load-carrying capacity,
diameter, width, offset, and be
mounted the same way as the one
it replaces.If you need to replace any of your
wheels, wheel bolts, wheel nuts,
or Tire Pressure Monitor System
(TPMS) sensors, replace them only
with new GM original equipment
parts. This way, you will be sure
to have the right wheel, wheel bolts,
wheel nuts, and TPMS sensors
for your vehicle.
{CAUTION
Using the wrong replacement
wheels, wheel bolts, or wheel nuts
on your vehicle can be dangerous.
It could affect the braking and
handling of your vehicle, make
your tires lose air and make you
lose control. You could have a
collision in which you or others
could be injured. Always use the
correct wheel, wheel bolts, and
wheel nuts for replacement.Notice:The wrong wheel can
also cause problems with bearing
life, brake cooling, speedometer
or odometer calibration, headlamp
aim, bumper height, vehicle
ground clearance, and tire or tire
chain clearance to the body and
chassis.
SeeChanging a Flat Tire on
page 5-66for more information.
Used Replacement Wheels
{CAUTION
Putting a used wheel on the
vehicle is dangerous. You cannot
know how it has been used or how
far it has been driven. It could fail
suddenly and cause a crash. If you
have to replace a wheel, use a
new GM original equipment wheel.
5-64 Service and Appearance Care

To store the jack tool bag and jack:
1. Return the tools to the jack
tool bag.
2. Secure the tool bag to the jack
by securely wrapping the straps
around the jack. Then, slide
the straps through the rings on
the bag and secure.
3. Reinstall the wing nut retainer to
fasten the jack and tool bag
under the rear seat.
Make sure that the wing nut
passes through the tool bag and
the jack before tightening it.
4. Turn the wing nut retainer
clockwise to secure.Spare Tire
The vehicle, when new, had a
fully-inated spare tire. A spare tire
may lose air over time, so check
its ination pressure regularly.
SeeInflation - Tire Pressure on
page 5-51andLoading the Vehicle
on page 4-35for information
regarding proper tire ination and
loading your vehicle. For instruction
on how to remove, install or store
a spare tire, seeRemoving the Flat
Tire and Installing the Spare Tire
on page 5-72andStoring a Flat or
Spare Tire and Tools (H3) on
page 5-78orStoring a Flat or Spare
Tire and Tools (H3T) on page 5-80.
After installing the spare tire on
your vehicle, you should stop
as soon as possible and make sure
the spare is correctly inated.The spare tire does not have a Tire
Pressure Monitor System sensor.
You may get a low pressure warning
light. SeeTire Pressure Monitor
Operation on page 5-54. Have the
damaged or at road tire repaired or
replaced as soon as you can.
Do not mix tires and wheels of
different sizes, because they will not
t. Keep your spare tire and its
wheel together.
5-82 Service and Appearance Care

Fuse Usage
11 Not Used
12Transfer Case Control
Module
13 Radio
14 Body Control Module
15Rear Wiper Motor
(H3 Only)
16Rear Wiper Pump
Switch (H3 Only)
17Air Injection Reactor
(AIR) Pump Relay/
Transmission Control
Module (TCM)
(V8 Only)
18 Rear Vision Camera
19 Cluster
20Rear Turn Lamp,
Hazard Lamp
21Powertrain Control
Module 1
22Mass Air Flow Sensor,
Canister Vent Purge
SolenoidFuse Usage
23 Injector/V8 Coil
24 Fog Lamp
25Powertrain Control
Module B
26Transmission Control
Module (TCM)
27 Airbags
28 Not Used
29Antilock Brakes,
StabiliTrak
®
30 Rear Window Defogger
31 Canister Vent
32Regulated Voltage
Control Sensor
33 Ignition 1 (V8 Only)
34 Transmission
35Cruise Control,
Miscellaneous
36 Horn
37Driver Side Rear
Park Lamp
Fuse Usage
38 Amplier
39Daytime Running
Lamps
40Passenger Side
Headlamp
41 Driver Side Headlamp
42 Trailer Back-Up Lamp
43 Front Park Lamps
44Air Injection Reactor
(AIR) Solenoid
45Auxiliary Power 2/
Cigarette Lighter
46Electronic Throttle
Control
47 Oxygen Sensor
48 Air Conditioning Clutch
49 Rear Park Lamp
50 Stop Lamp
51Auxiliary Power 1/
Cigarette Lighter
52StabiliTrak
®, Antilock
Brakes
5-94 Service and Appearance Care