2009 HUMMER H3 maintenance schedule

Engine Air Cleaner/Filter
The engine air cleaner/lter is
located in the engine compartment
on the passenger side of the
vehicle. SeeEngine Compartment
Overview on page 5-10for more
information on location.
When to Inspect the Engine
Air Cleaner/Filter
Inspect the air cleaner/lter at the
MaintenanceIIintervals and replace
it at the rst oil change after each
50,000 mile (80 000 km) interval.SeeScheduled Maintenance on
page 6-4for more information. If you
are driving in dusty/dirty conditions,
inspect the lter at each engine
oil change.
How to Inspect the Engine Air
Cleaner/Filter
To inspect or replace the engine air
cleaner/lter:
1. Unfasten the clips that hold the
cover on and remove the cover.
2. Lift out the engine air
cleaner/lter.
3. Inspect or replace the air lter.
SeeMaintenance Replacement
Parts on page 6-14to
determine which lter to use.
4. Reinstall the engine air
cleaner/lter cover. Fasten the
clips to hold the cover in place.
{CAUTION
Operating the engine with the
air cleaner/lter off can cause you
or others to be burned. The air
cleaner not only cleans the air;
it helps to stop ames if the
engine backres. If it is not there
and the engine backres, you
could be burned. Do not drive
with it off, and be careful
working on the engine with the
air cleaner/lter off.
Notice:If the air cleaner/lter
is off, a backre can cause a
damaging engine re. And, dirt
can easily get into the engine,
which will damage it. Always have
the air cleaner/lter in place when
you are driving. 3.7 L shown (5.3 L similar)
Service and Appearance Care 5-17

Checking the Fluid Level
To prepare the vehicle:
1. Park the vehicle on a level place.
Keep the engine running.
2. With the parking brake applied,
place the shift lever in P (Park).
3. With your foot on the brake
pedal, move the shift lever
through each gear range,
pausing for about three seconds
in each range. Then, position
the shift lever in P (Park).
4. Let the engine run at idle for
three minutes or more.
Then, without shutting off the
engine:
1. Flip the handle up and then pull
out the dipstick and wipe it with
a clean rag or paper towel.The automatic transmission
dipstick handle with this symbol
on it is located in the engine
compartment on the passenger
side of the vehicle.
SeeEngine Compartment
Overview on page 5-10for more
information on location.
2. Push it back in all the way, wait
three seconds, and pull it back
out again.
3. Check both sides of the dipstick,
and read the lower level.
The uid level must be in
the COLD area, below thecross-hatched area, for a
cold check or in the HOT or
cross-hatched area for a
hot check. Be sure to keep the
dipstick pointed down to get
an accurate reading.
4. If the uid level is in the
acceptable range, push
the dipstick back in all the way;
then ip the handle down to
lock the dipstick in place.
How to Add Automatic
Transmission Fluid
Refer to the Maintenance
Schedule to determine what kind
of transmission uid to use.
SeeRecommended Fluids and
Lubricants on page 6-12.
Add uid only after checking the
transmission uid while it is hot.
A cold check is used only as
a reference. If the uid level is low,
add only enough of the proper
uid to bring the level up to the
HOT area for a hot check.
Service and Appearance Care 5-19

3. Check that the lubricant level
is up to the bottom of the ller
plug hole.
4. If the uid level is good, install
the plug and be sure it is fully
seated. If the uid level is low,
add more uid as described
in the next steps.
How to Add Fluid
Refer to the Maintenance Schedule
to determine what kind of uid to
use. SeeRecommended Fluids and
Lubricants on page 6-12.
1. Remove the ller plug.
2. Add uid at the ller plug hole.
Add only enough uid to bring
the uid level up to the bottom of
the ller plug hole.
3. Install the ller plug. Be sure the
plug is fully seated.
Hydraulic Clutch
The hydraulic clutch linkage in
the vehicle is self-adjusting.
The clutch master cylinder reservoir
is lled with hydraulic clutch uid.
The hydraulic clutch uid reservoir
cap has this symbol on it. See
Engine Compartment Overview on
page 5-10for reservoir location.
It is not necessary to regularly check
clutch uid unless a leak in the
system is suspected. Adding uid
will not correct a leak.
A uid loss in this system could
indicate a problem. Have the system
inspected and repaired.
When to Check and What
to Use
Refer to the Maintenance Schedule
to determine how often to check
the uid level in the clutch master
cylinder reservoir and for the proper
uid. SeeRecommended Fluids
and Lubricants on page 6-12.
How to Check and Add Fluid
The proper uid should be added
if the level does not reach the
bottom of the diaphragm when it is
in place in the reservoir. See the
instructions on the reservoir cap.
Service and Appearance Care 5-21

Do not top off the brake uid. Adding
uid does not correct a leak. If uid is
added when the linings are worn,
there will be too much uid when new
brake linings are installed. Add or
remove brake uid, as necessary,
only when work is done on the brake
hydraulic system.
{CAUTION
If too much brake uid is added,
it can spill on the engine and
burn, if the engine is hot enough.
You or others could be burned,
and the vehicle could be
damaged. Add brake uid only
when work is done on the brake
hydraulic system. See “Checking
Brake Fluid” in this section.
Refer to the Maintenance Schedule
to determine when to check the
brake uid. SeeScheduled
Maintenance on page 6-4.
Checking Brake Fluid
Check brake uid by looking at the
brake uid reservoir. SeeEngine
Compartment Overview on
page 5-10.
The uid level should be above
MIN. If it is not, have the brake
hydraulic system checked to see
if there is a leak.
After work is done on the brake
hydraulic system, make sure the
level is above the MIN but not over
the MAX mark.
What to Add
Use only new DOT-3 brake uid
from a sealed container. See
Recommended Fluids and
Lubricants on page 6-12.
Always clean the brake uid
reservoir cap and the area around
the cap before removing it. This
helps keep dirt from entering
the reservoir.{CAUTION
With the wrong kind of uid in the
brake hydraulic system, the brakes
might not work well. This could
cause a crash. Always use the
proper brake uid.
Notice:
Using the wrong uid can badly
damage brake hydraulic system
parts. For example, just a few
drops of mineral-based oil,
such as engine oil, in the brake
hydraulic system can damage
brake hydraulic system parts so
badly that they will have to be
replaced. Do not let someone
put in the wrong kind of uid.
If brake uid is spilled on the
vehicle’s painted surfaces, the
paint nish can be damaged.
Be careful not to spill brake uid
on the vehicle. If you do, wash it
off immediately. SeeWashing
Your Vehicle on page 5-86.
Service and Appearance Care 5-31

Windshield Wiper
Blade Replacement
Windshield wiper blades should be
inspected for wear and cracking.
SeeScheduled Maintenance
on page 6-4for more information.
Replacement blades come in
different types and are removed in
different ways. For proper type
and length, seeMaintenance
Replacement Parts on page 6-14.
To replace the windshield wiper
blade:
1. Lift the wiper arm away from the
windshield.2. Push the release lever (B) to
disengage the hook and push
the wiper arm (A) out of the
blade (C).
3. Push the new wiper blade
securely on the wiper arm
until you hear the release lever
click into place.
To replace the rear wiper blade,
lift the rear wiper arm from the
window and pull the blade.
Tires
Your new vehicle comes with
high-quality tires made by
a leading tire manufacturer.
If you ever have questions about
your tire warranty and where
to obtain service, see your
vehicle Warranty booklet
for details. For additional
information refer to the tire
manufacturer.
{CAUTION
Poorly maintained and
improperly used tires are
dangerous.
Overloading your
vehicle’s tires can
cause overheating as a
result of too much exing.
You could have an air-out
and a serious accident.
SeeLoading the Vehicle
on page 4-35.
(Continued)
5-44 Service and Appearance Care

8. Proceed to the driver side rear
tire, and repeat the procedure
in Step 5.
9. After hearing the conrming horn
chirp for the driver side rear tire,
check to see if the TPMS low tire
warning light and the DIC LOW
TIRE messages have turned off.
If yes, the TPMS sensors have
been relearned. Turn the ignition
switch to LOCK/OFF.
If the low tire warning light and
the SERV TPM message on the
DIC are on after completing
Step 5 for the driver side rear tire,
the sensor relearn process has
not been successful. Turn the
ignition switch to LOCK/OFF and
repeat the matching process
beginning with Step 2.
10. Set all four tires to the
recommended air pressure level
as indicated on the Tire and
Loading Information label.
11. Put the valve caps back on the
valve stems.Tire Inspection and
Rotation
We recommend that you
regularly inspect the vehicle’s
tires, including the spare tire,
for signs of wear or damage.
SeeWhen It Is Time for
New Tires on page 5-58for
more information.
Tires should be rotated
every 5,000 to 8,000 miles
(8 000 to 13 000 km).
SeeScheduled Maintenance
on page 6-4.
The purpose of a regular tire
rotation is to achieve a uniform
wear for all tires on the vehicle.
This will ensure that the
vehicle continues to perform
most like it did when the
tires were new.Any time you notice unusual
wear, rotate the tires as soon
as possible and check wheel
alignment. Also check for
damaged tires or wheels.
SeeWhen It Is Time for
New Tires on page 5-58and
Wheel Replacement on
page 5-64.
Make sure the spare tire is
stored securely. Push, pull and
then try to rotate or turn the
tire. If it moves, use the wheel
wrench/hoist shaft to tighten
the cable. SeeChanging a
Flat Tire on page 5-66.
Service and Appearance Care 5-57

Maintenance
Schedule
Maintenance Schedule
Introduction.........................6-1
Maintenance
Requirements....................6-2
Your Vehicle and the
Environment......................6-2
Using the Maintenance
Schedule...........................6-2
Scheduled Maintenance......6-4
Additional Required
Services............................6-6
Maintenance Footnotes.......6-7
Owner Checks and
Services............................6-9
At Each Fuel Fill................6-9
At Least Once a Month......6-9
At Least Once a Year.......6-10
Recommended Fluids and
Lubricants.......................6-12
Maintenance
Replacement Parts..........6-14
Engine Drive Belt Routing. . .6-15
Maintenance Record.........6-16
Maintenance
Schedule
Introduction
Important: Keep engine oil at
the proper level and change as
recommended.
Have you purchased the
GM Protection Plan? The Plan
supplements the vehicle warranties.
See the Warranty and Owner
Assistance booklet or your
dealer/retailer for details.
Maintenance Schedule 6-1

Maintenance
Requirements
Notice:Maintenance intervals,
checks, inspections, replacement
parts, and recommended uids
and lubricants as prescribed
in this manual are necessary to
keep this vehicle in good working
condition. Any damage caused
by failure to follow scheduled
maintenance might not be
covered by the vehicle warranty.
Your Vehicle and the
Environment
Proper vehicle maintenance not only
helps to keep the vehicle in good
working condition, but also helps the
environment. All recommended
maintenance is important. Improper
vehicle maintenance can even
affect the quality of the air webreathe. Improper uid levels or the
wrong tire ination can increase
the level of emissions from the
vehicle. To help protect the
environment, and to keep the
vehicle in good condition, be sure to
maintain the vehicle properly.
Using the Maintenance
Schedule
We want to help keep this vehicle in
good working condition. But we
do not know exactly how you
will drive it. You might drive very
short distances only a few times a
week. Or you might drive long
distances all the time in very hot,
dusty weather. You might use
the vehicle in making deliveries.
Or you might drive it to work, to do
errands, or in many other ways.Because of all the different ways
people use their vehicles,
maintenance needs vary. You might
need more frequent checks and
replacements. So please read the
following and note how you drive.
If you have any questions on how to
keep the vehicle in good condition,
see your dealer/retailer.
This schedule is for vehicles that:carry passengers and cargo
within recommended limits on the
Tire and Loading Information
label. SeeLoading the Vehicle
on page 4-35.
are driven on reasonable road
surfaces within legal driving limits.
are driven off-road in the
recommended manner. See
Off-Road Driving on page 4-13.
use the recommended fuel.
SeeGasoline Octane on
page 5-5.
6-2 Maintenance Schedule