Inst Panel/TPMS/Cruise/Compass
Temperature
GaugeMessage in the Information Display
Check Fuel Cap: Fuel cap is missing or not
properly tightened. Check that the fuel cap
is installed and tightened at least one click.
Temperature Gauge: If the pointer is in the
red zone, turn off the engine immediately, or
as soon as safely possible*.
Instrument Panel Indicators
Indicators should go out shortly after
starting the engine. If an indicator stays on
or comes on while driving, follow the
instructions in the description.
• Red indicators are critical and require immediate attention.
• Amber indicators are urgent and require attention as soon as possible.
• Blue and green indicators are used for general information.
Charging system indicator:
Battery is not being charged; see
dealer as soon as possible.
Low oil pressure indicator: Low
oil pressure; turn the engine off as
soon as safely possible.
Security system indicator: Blinks
when the security system is armed.
Supplemental restraint system (SRS) indicator:
SRS malfunction; see dealer as soon as
possible.*
Seat belt reminder light: Fasten seat belts.
Parking brake and brake system indicator:
Parking brake on, low brake fluid level.
Door and trunk open monitor: Comes on if the
trunk lid is left open. Will go out after about 3
minutes, even if the lid is not closed.
Malfunction indicator lamp (CHECK engine
light): Engine or emissions system malfunction;
have dealer inspect the vehicle.
Maintenance minder indicator: A scheduled
maintenance is due; stays on if maintenance is
past due.
Fuel gauge/low fuel indicator
Note: It is important to see the Instruments and Controls section in the\
owner’s manual.
09 AccordCoupe:09 Accord Coupe.qxd 6/16/2008 1:41 PM Page 3
* Check the owner’s manual for additional information and instructions. HFL/
HomeLink
®
Press and hold the button on the
remote and the HomeLink button at
the same time. Then, while
continuing to hold the HomeLink
button, press and release the button
on the remote every 2 seconds.
Does the LED blink at a faster rate within 20
seconds?
Press and hold the
HomeLink button
again. Training
complete
YES
NO
HomeLink indicator
flashes for 2 seconds,
then remains on. HomeLink LED
remains on.
YES
NO YES
NO
Position the remote transmitter you
wish to link 1–3 inches from the
HomeLink button you want to program.1
Press and hold the desired HomeLink
button and the button on the remote
transmitter you wish to link.
Does the HomeLink indicator (LED) blink at a
faster rate after about 10 seconds?
2
aThe remote has a rolling code.
Press the “learn” button on the
remotely controlled device (e.g.,
garage door opener).
Press the programmed HomeLink
button again; the remotely
controlled device should operate. Within 30 seconds, press and hold
the programmed HomeLink button
for 2 seconds.a
Press and hold the programmed
HomeLink button for about a
second.
Does the device (garage door opener) work?
3
b
4
5
Training a Button
Indicator remains
on for about 25
seconds (standard
transmitter). Indicator flashes rapidly
for 2 seconds, then
remains on for about 23
seconds (rolling code
transmitter).
Press and hold the desired
HomeLink button until the HomeLink
indicator begins to flash slowly.
When the indicator begins to flash
slowly, continue to hold the HomeLink
button and follow steps 1– 4 under
Training a Button.1
2
Retraining a Button
Erasing CodesTo erase codes stored in all buttons,
press and hold the two outer buttons until
the HomeLink indicator begins to flash
(about 10 to 20 seconds), then release
the buttons.
You should erase all three codes before
selling the vehicle.
If you have any problems programming
HomeLink, see the owner's manual included with
the device you are trying to program, or call
HomeLink at 1-800-355-3515 or go online to
www.homelink.com .
HomeLink®(if equipped)The HomeLink® Universal Transceiver built into your vehicle can be programmed to operate up to th\
ree remote
controlled devices around your home, such as garage doors, lighting, or \
home security systems.
09 AccordCoupe:09 Accord Coupe.qxd 6/16/2008 1:41 PM Page 16